Gebruiksaanwijzing /service van het product Corsa (2009) van de fabrikant Vauxhall
Ga naar pagina of 211
0 - 1 VAUXHALL Corsa VAUXHALL Corsa Owner’s Manual Model Year 2009.5 Edition: January 2009 TS 1651-B-09.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 33 Storage ........................................ 50 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available under the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Turn the key in the driver's door lock to the front or press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, pull the button underneath the tailgate moulding.
In brief 7 Seat backrests Turn handwheel. Do not lean on seat backrest when adjusting. Seat adjustment 3 35, Seat position 3 34, Folding front passenger seat backrest 3 36. Seat height Lever pumping motion up = higher down = lower Seats 3 35, Seat position 3 34.
8 In brief Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle.
In brief 9 Setting with four-way switch in version with electronic window operation First select the relevant exterior mirror then use the control to adjust. Electric adjustment 3 27, Convex exterior mirrors 3 27, Folding exterior mirrors 3 27, Heated exterior mirrors 3 28.
10 In brief Instrument panel overview.
In brief 11 1 Side air vents ...................... 109 2 Light switch .......................... 93 Instrument illumination ......... 98 Rear fog light ......................... 97 Front fog lights ..................... 97 Headlight range adjustment .
12 In brief.
In brief 13 Exterior lighting Turn light switch: 7 = Off 8 = Side lights 9 = Headlights Press > = Front fog lights r = Rear fog lights Lighting 3 93. Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = push or pull lever High beam 3 94, Headlight flash 3 94, Automatic light control 3 93.
14 In brief Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 96. Horn Press j . Washer and wiper systems Windscreen wiper & = fast % = slow $ = timed interval wipe or automatic wiping with rain sensor § = off For a single swipe when the windscreen wiper is off, press the lever down.
In brief 15 Windscreen and headlight washer systems Pull lever. Windscreen and headlight washer system 3 68, Washer fluid 3 139. Rear window wiper and washer system Wiper on = push lever Wiper off = push lever again Wash = push lever and hold Rear window wiper and washer system 3 69, Wiper blade replacement 3 140, Washer fluid 3 139.
16 In brief Demisting and defrosting the windows Air distribution to l . Set temperature control to warmest level. Set fan speed to highest level. Cooling n on.
In brief 17 Automatic transmission P = park R = reverse N = neutral D = drive The selector lever can only be moved out of P or N when the ignition is on and the foot brake is depressed (selector lever lock). To engage P or R , push button on selector lever.
18 In brief Parking ■ Always apply parking brake. Manual parking brake without pressing release button. Apply as firmly as possible on a downhill slope or uphill slope. Operate foot brake at the same time to reduce operating force. ■ Switch off the engine and ignition.
Keys, doors and windows 19 Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 27 Interior mirrors .
20 Keys, doors and windows Radio remote control Used to operate: ■ Central locking system, ■ Anti-theft locking system, ■ Anti-theft alarm system, ■ Power windows. The radio remote control has a range of approx. 5 metres (16 ft). This range can be affected by outside influences.
Keys, doors and windows 21 Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock.
22 Keys, doors and windows Central locking system with key activation Turn the key in the driver's door lock rearwards. Central locking system with radio remote control Press button p . Central locking button Press button m : the doors are locked or unlocked.
Keys, doors and windows 23 Fault in radio remote control Unlocking Turn key in the driver's door lock to the front, as far as it will go. The entire vehicle is unlocked when the driver's door is opened. To open the other doors, switch on the ignition and press the central locking button.
24 Keys, doors and windows 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn button on rear door lock to the horizontal position: door cannot be opened from inside. Doors Load compartment Opening Pull the button underneath the moulding.
Keys, doors and windows 25 Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed or the system cannot be activated.
26 Keys, doors and windows Seek the assistance of a workshop in the event of faults. Alarm When triggered, the alarm gives off an acoustic signal (horn) and a visual signal (hazard warning flashers). The number and duration of which are stipulated by legislation.
Keys, doors and windows 27 Exterior mirrors Convex shape The convex exterior mirror reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the abilty to estimate distances.
28 Keys, doors and windows Corsa VXR: For pedestrian safety, the exterior mirrors of the Corsa VXR are released from the holder if they are bumped. Fit mirror housing to holder with latching lugs and engage by striking gently. Manual The exterior mirrors can be folded in by pressing gently on the outer edge of the housing.
Keys, doors and windows 29 Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced. Windows Manual windows The door windows can be opened or closed with the window winders.
30 Keys, doors and windows Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Keep a close watch on the windows when closing them.
Keys, doors and windows 31 Fault If the windows cannot be opened or closed automatically, activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Close the window completely and operate the button for a further 5 seconds.
32 Keys, doors and windows Operated via a rocker switch in the roof console. Press the button briefly for activation in steps. Hold down the button for longer for automatic opening. Raise With the sunroof closed, press ü . The sunroof is raised at the rear.
Seats, restraints 33 Seats, restraints Head restraints ............................ 33 Front seats ................................... 34 Seat belts ..................................... 37 Airbag system .............................. 39 Child restraints .
34 Seats, restraints Head restraints on rear seats The height of the head restraints can be set in two positions. To set in the first position, pull the head restraint upwards, in the second position press the spring marked in the illustration and push the head restraint right up to the top.
Seats, restraints 35 Seat adjustment 9 Danger Do not sit nearer than 25 cm (10 inches) from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull handle, slide seat, release handle.
36 Seats, restraints Seat folding Lift release lever and tilt backrest forwards. Lower release lever and backrest engages in lowered position. Slide seat forwards. To return the backrest to its original upright position: First slide seat back and it will engage in its original position.
Seats, restraints 37 Seat belts The belts are locked during heavy acceleration or deceleration of the vehicle for the safety of the occupants. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves.
38 Seats, restraints Triggered belt tensioners must be replaced by a workshop. Belt tensioners can only be triggered once. Notice Do not affix or install accessories or other objects that may interfere with the operation of the belt tensioners.
Seats, restraints 39 Removing To release belt, press red button on belt buckle. Seat belts on the rear outer seats When not in use or to fold forward the rear backrests, feed seat belts through belt mount.
40 Seats, restraints Notice The airbag systems and belt tensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not stick anything on the airbag covers and do not cover them with other materials.
Seats, restraints 41 The front airbag system is triggered in the event of an accident of a certain severity in the depicted area. The ignition must be on. The forward movement of the front seat occupants is decelerated, thereby considerably reducing the risk of injury to the upper body and head.
42 Seats, restraints The risk of injury to the upper body and pelvis in the event of a side-on collision is considerably reduced. 9 Warning Keep the area in which the airbag inflates clear of obstructions. Notice Only use protective seat covers that have been approved for the vehicle.
Seats, restraints 43 The risk of injury to the head in the event of a side impact is considerably reduced. 9 Warning Keep the area in which the airbag inflates clear of obstructions. The hooks on the handles in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers.
44 Seats, restraints Deactivation: ■ switch on ignition, control indicator W flashes, ■ press button W within 15 seconds and hold down, ■ after about 2 seconds, you will hear a confirmation buzzer. Release button W after another 4 seconds at the latest.
Seats, restraints 45 Selecting the right system Children should travel facing backwards in the vehicle, until as old as possible. It is appropriate to change the system when the child's head can no longer be properly supported at eye height.
46 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat active airbag deactivated airbag Group 0: up to 10 kg or approx.
Seats, restraints 47 Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to .
48 Seats, restraints ISOFIX size class and seat device A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints 49 Isofix child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the mounting brackets. When using ISOFIX mounting brackets for seat mounting, universally approved child restraint systems for ISOFIX may be used.
50 Storage Storage Storage compartments ................ 50 Load compartment ....................... 59 Roof rack system ......................... 64 Loading information ..................... 64 Storage compartments Glovebox The glovebox features: ■ card holder in cheque card format ■ pen holder ■ pocket torch holder.
Storage 51 Underseat storage Lift at recessed edge and pull out. Maximum load: 1.5 kg. To close, push in and engage. Rear carrier system The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor.
52 Storage Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again. 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged.
Storage 53 Push the clamping lever down and push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located.
54 Storage Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5).
Storage 55 Press the release lever and withdraw the wheel recesses. Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Rotate the left pedal (opposite the chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal.
56 Storage Insert pedal crank mount into outer rail of each pedal crank recess from above and slide downwards as far as it will go. Attach the pedal crank by rotating the attachment screw on the pedal crank mount. Place the wheel recesses such that the bicycle is more or less horizontal.
Storage 57 Tighten the attachment screw for the pedal bearing mount to its maximum point. Secure both bicycle wheels to wheel recesses using strap retainers. Check the bicycle to make sure it is secure. The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle.
58 Storage Insert the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down.
Storage 59 Push the clamping lever down and pull both bulb holders out of their recesses. Fold in the bulb holders on the backs of the tail lamps. First place the front tail lamp ( 1 ), then the rear tail lamp ( 2 ) in their recesses and push down as far as possible.
60 Storage If the backrest is split, unlock the relevant side, and unlock at both sides if it is a single unit. Folding down rear backrests Remove load compartment cover as necessary. Push head restraints down by pressing the catch. Guide the seat belts through belt mounts to protect them against damage.
Storage 61 5-door Hatchback Lift the cover rearwards, until it unlatches, then remove. Fit in reverse order. 3-door Hatchback Lift the cover rearwards until it unlatches, set at an angle, then remove.
62 Storage To remove the three other segments (order 2 to 4) lift at the rear, disengage, twist and remove. Install the segments in the order 4 to 1. Engage segments in recesses at the side. The segments overlap at the connecting points when they are closed.
Storage 63 Lashing eyes The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or luggage net. Warning triangle Store warning triangle in rear load compartment wall: first fit warning triangle into recess on left and then insert in guide on right.
64 Storage Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Follow the installation instructions and remove the roof rack when not in use.
Storage 65 ■ When transporting objects in the load compartment, the backrests of the rear seats must not be folded forward. ■ Do not allow the load to protrude above the upper edge of the backrests. ■ Do not place any objects on the load compartment cover or the instrument panel, and do not cover the sensor on top of the instrument panel.
66 Instruments and controls Instruments and controls Controls ....................................... 66 Warning lights, gauges and indicators ..................................... 72 Information displays ..................... 81 Vehicle messages ....
Instruments and controls 67 Heated steering wheel Activate steering wheel heating in combination with the seat heating by pressing the ß * button with the ignition on until the desired setting is reached. LED ß on: driver seat heating on. LED ß and * on: driver seat heating and steering wheel heating on.
68 Instruments and controls Windscreen wiper/washer Windscreen wiper The lever always springs back to its original position. & = fast % = slow $ = adjustable timed interval wipe § = off For a single swipe when the windscreen wiper is off, press the lever down.
Instruments and controls 69 Keep the sensor free from dust, dirt and ice. Windscreen washer Pull lever. Washer fluid is sprayed onto the windscreen and the wiper swipes for a few strokes. Rear window wiper/washer Push lever forwards. The rear window wiper swipes in interval mode.
70 Instruments and controls In vehicles with Graphic-Info-Display or Color-Info-Display, a warning message appears in the display as a warning for icy road conditions. There is no message below -5 °C. 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C.
Instruments and controls 71 Power outlets The power outlet is located in the centre console. Caution Do not damage the outlet by using unsuitable plugs. Connecting electrical accessories while the engine is off will discharge the battery. Do not exceed the maximum power consumption of 120 watts.
72 Instruments and controls Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on.
Instruments and controls 73 Fuel gauge Displays the fuel level in the tank. If the fuel level is too low, Y illuminates. When the control indicator flashes, refuel immediately. Never run the tank dry. Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity.
74 Instruments and controls Control indicators The control indicators described are not present in all vehicles. The description applies to all instrument versions. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
Instruments and controls 75 Control indicators in the instrument cluster.
76 Instruments and controls Turn signal O illuminates or flashes green. Illuminates The control indicator illuminates briefly when the parking lights are switched on 3 97. Flashes The control indicator flashes if a turn signal or the hazard warning flashers are activated.
Instruments and controls 77 Flashes during or after engine start Battery voltage too low. Have electrical system tested by a workshop. Malfunction indicator light Z illuminates or flashes yellow. Illuminates when the ignition is switched on and goes out shortly after the engine starts.
78 Instruments and controls Illuminates for a few seconds after the ignition is turned on. The system is ready for operation when the control indicator goes out. If the control indicator does not go out after a few seconds, or if it illuminates while driving, there is a fault in the ABS.
Instruments and controls 79 Check coolant level 3 138. If there is sufficient coolant, consult a workshop. Preheating and diesel particle filter ! illuminates or flashes yellow. Illuminates Preheating activated. Only activates when outside temperature is low.
80 Instruments and controls 9 Warning When the engine is off, considerably more force is needed to brake and steer. Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Seek the assistance of a workshop.
Instruments and controls 81 Illuminated when the rear fog light is on 3 97. Cruise control m illuminates or flashes green. Illuminates Illuminates when the system is on 3 125. Flashes Cruise control was enabled without depressing the brake pedal beforehand.
82 Instruments and controls Selecting functions Functions and settings of the Infotainment system and electronic climate control system are accessed via the display. Selections are made via the menus and buttons, the multifunction control of the Infotainment system or the left adjuster wheel of the steering wheel.
Instruments and controls 83 Function areas For each function area there is a main page (Main), which is selected at the top edge of the display (not with the Infotainment system CD 30 or the handsfree mobile phone system): ■ Audio, ■ Navigation, ■ Telephone, ■ Trip computer.
84 Instruments and controls On Infotainment systems with navigation, time and date are also harmonised upon receipt of a GPS satellite signal. The function is activated by highlighting the field in front of Synchron. clock automatical. in the Time, Date menu.
Instruments and controls 85 Adjusting contrast ( Graphic-Info-Display) Select menu item Contrast from the Settings menu. Confirm the required setting. Setting display mode Display brightness is dependent on vehicle lighting. Additional settings can be made as follows: Select menu item Day / Night from the Settings menu.
86 Instruments and controls engine is running, a gear is engaged and the foot brake is not depressed. ■ Warning signal sounds three times if the rear carrier system is extended and reverse gear is selected. When the vehicle is parked and the driver's door is opened ■ When the key is in the ignition switch.
Instruments and controls 87 Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically.
88 Instruments and controls Average consumption Display of average consumption. Stop watch Measurement of the time from activation to deactivation. Press the 7 button to start and stop the measurement.
Instruments and controls 89 Instantaneous consumption Displays the instantaneous consumption. At low speeds, consumption per hour is displayed. Distance Display of distance travelled. Average speed Display of average speed. Stoppages in the journey with the ignition off are not included in the calculations.
90 Instruments and controls Stop watch Select menu item Stop Watch from the Board Computer menu. To start, select menu item Start . To stop, select menu item Stop . To reset, select menu item Reset . The relevant stop watch display can be selected in the Options menu: Driving Time excl.
Instruments and controls 91 ■ Pull turn signal lever and wiper lever simultaneously to the steering wheel until you hear a confirmation signal (approx. 3 seconds). ■ The odometer display shows P1 . ■ Push the turn signal lever (left) up or down and select the desired function P1 - P7 .
92 Instruments and controls P4 : Automatic locking 3 23. P5 : Selective unlocking 3 21. P6 : Speed warning 3 72. P7 : Volume of the acoustic turn signal 3 96.
Lighting 93 Lighting Exterior lighting ............................ 93 Interior lighting ............................. 98 Lighting features .......................... 99 Exterior lighting Light switch Turn light switch: 7 = Off 8 = Side lights 9 = Headlights Control indicator 8 3 80.
94 Lighting High beam To switch from low to high beam, push lever. To switch to low beam, push lever again or pull. Headlight flash To activate the headlight flash, pull lever.
Lighting 95 Vehicles with adaptive forward lighting Adapting the aim of the headlight beam: 1. Pull turn signal lever and hold until control indicator f starts flashing. 2. Switch on ignition. 3. An acoustic signal sounds after approx. 3 seconds. Control indicator f 3 80.
96 Lighting Hazard warning flashers Operated with the ¨ button. The hazard warning flashers activate automatically if the airbags deploy. Turn and lane-change signals Lever up = right turn signal Lever down = left turn signal The lever always springs back to its original position.
Lighting 97 Front fog lights The front fog lights can only be switched on when both the ignition and headlights are on. Operated with the > button. Rear fog lights The rear fog light can only be switched on when both the ignition and headlights or side lights (with front fog lights) are on.
98 Lighting Interior lighting Instrument panel illumination control Brightness can be adjusted when the exterior lights are on: Brighter = Push button < Darker = Push button ] Hold down the button until the required brightness is achieved.
Lighting 99 Rear courtesy lights Operated with switch (I = on, 0 = off, centre = automatic). Load compartment lighting The lighting switches on when opened. Reading lights Operated with a buttons with ignition on. Lighting features Centre console lighting Spotlight in interior mirror housing.
100 Lighting Activating 1. Switch off ignition. 2. Remove ignition key. 3. Open driver's door. 4. Pull turn signal lever. 5. Close driver's door.
Infotainment system 101 Infotainment system Introduction ................................ 101 Radio ......................................... 101 Audio players .
102 Infotainment system Audio players Auxiliary devices The AUX input is located in the centre console in front of the gearshift lever. Always keep the AUX input clean and dry. Further information is available in the Infotainment system manual. AUX input An external audio source such as a portable CD player can be connected using a 3.
Infotainment system 103 Caution Mobile telephones and radio equipment may lead to malfunctions in the vehicle electronics when operated inside the vehicle with no exterior antenna, unless the above mentioned regulations are observed.
104 Climate control Climate control Climate control systems ............. 104 Air vents ..................................... 109 Maintenance .............................. 109 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 31.
Climate control 105 ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J .
106 Climate control Demisting and defrosting the windows ■ Cooling n on. ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to l . ■ Switch on heated rear window Ü . ■ Open side air vents as required and direct them towards the door windows.
Climate control 107 The electronic climate control system is only fully operational when the engine is running. For correct operation do not cover the sensor on the instrument panel. Automatic mode Basic setting for maximum comfort: ■ Press AUTO button.
108 Climate control Cooling In the Climate menu, select menu item AC and activate or deactivate cooling. The air conditioning system cools and dehumidifies (dries) when outside temperature is above a specific level. Therefore condensation may form and drip from under the vehicle.
Climate control 109 Air vents Adjustable air vents At least one air vent must be open while cooling is on in order to prevent the evaporator from icing up due to lack of air movement. Set the direction of the air flow by turning the adjuster wheel from right to left and raise or lower the horizontal slats.
110 Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
Driving and operating 111 Driving and operating Driving hints ............................... 111 Starting and operating ............... 111 Engine exhaust .......................... 113 Automatic transmission .............. 115 Manual transmission ..
112 Driving and operating Ignition switch positions 0 = Ignition off 1 = Steering wheel lock released, ignition off 2 = Ignition on, for diesel engine: preheating 3 = Starting Starting the engine Oper.
Driving and operating 113 switching off the ignition. On an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear or set the selector lever to P before switching off the ignition. Turn the front wheels towards the kerb.
114 Driving and operating Stopping the journey or switching off the engine during cleaning is not recommended. Caution If the cleaning process is interrupted more than once, there is a great risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads.
Driving and operating 115 Automatic transmission The automatic transmission permits automatic gearshifting. Transmission display The mode or selected gear is shown in the transmission display.
116 Driving and operating Rocking the vehicle Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud or snow. Move the selector lever between D and R in a repeat pattern. Do not race the engine and avoid sudden acceleration. Parking Apply the parking brake and engage P .
Driving and operating 117 Kickdown If the accelerator pedal is pressed past the pressure point, the transmission shifts to a lower gear depending on engine speed. Fault In the event of a fault, A illuminates. The transmission no longer shifts automatically.
118 Driving and operating 3. Push the yellow catch forward with a screwdriver and move the selector lever out of P . If P is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop.
Driving and operating 119 Manual transmission automated This transmission permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.
120 Driving and operating If neither the accelerator nor the brake pedal are depressed, no gear is engaged and A or R flashes for a brief time in the display. Stopping the vehicle In A , first gear is engaged and the clutch is released when the vehicle is stopped.
Driving and operating 121 Sport mode Shift times are reduced when the Sport mode is enabled, and the gears are shifted at higher engine speeds, although not when cruise control is activated.
122 Driving and operating Fault To prevent damage to the manual transmission automated, the clutch is engaged automatically at high clutch temperatures. A illuminates in the event of a fault. Continued driving is possible. Manual mode cannot be used for shifting.
Driving and operating 123 Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when you depress the brake pedal firmly.
124 Driving and operating Parking brake Always apply parking brake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope. To release the parking brake, pull the lever up slightly, press the release button and fully lower the lever.
Driving and operating 125 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Control indicator v 3 78. Deactivation ESP® Plus can be deactivated by pressing the v button. When ESP® Plus is deactivated the control indicator v illuminates.
126 Driving and operating With automatic transmission or manual transmission automated, only activate cruise control in automatic mode. Control indicator m 3 81. Activation Turn switch m up and release: the current speed is stored and maintained. Vehicle speed can be increased by depressing the accelerator pedal.
Driving and operating 127 Activation When reverse gear is engaged, the system switches itself on automatically. The system can also be activated at low speed by pressing the r button. An obstacle is indicated by buzzers. The interval between the buzzers becomes shorter as the vehicle gets closer to the obstacle.
128 Driving and operating a biodiesel (= FAME according to EN14214) content of max. 7 % by volume (like DIN 51628 or equivalent standards) may be used. Do not use marine diesel oils, heating oils or entirely or partially plant-based diesel fuels, such as rape seed oil or bio diesel, Aquazole and similar diesel-water emulsions.
Driving and operating 129 Unlock the fuel filler cap with the ignition key, unscrew and remove. The fuel filler cap can be retained in the bracket on the fuel filler flap. Caution Wipe off any overflowing fuel immediately. Fuel filler cap Only a genuine fuel filler cap provides full functionality.
130 Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment.
Driving and operating 131 the case of heavy trailers. The vertical coupling load should never fall below 25 kg. Rear axle load When the trailer is coupled and the towing vehicle fully loaded, the perm.
132 Driving and operating Disengage and fold down the socket. Remove the sealing plug from the opening for the coupling ball bar and stow it. Checking the tensioning of the coupling ball bar ■ The rotary knob rests on the coupling ball bar. ■ Green marking on the rotary knob is not visible.
Driving and operating 133 Inserting the coupling ball bar Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary knob snaps back into its original position resting against the coupling ball bar without a gap.
134 Driving and operating Dismounting the coupling ball bar Insert the key in the lock and unlock the coupling ball bar. Push the rotary knob onto the coupling ball bar and rotate right while pressed down until it engages. Pull out the ball bar downwards.
Vehicle care 135 Vehicle care General Information ................... 135 Vehicle checks ........................... 136 Bulb replacement ....................... 141 Electrical system ........................ 154 Vehicle tools ........................
136 Vehicle care ■ Check the engine oil level. ■ Check the coolant level. ■ Fit the number plate if necessary. End-of-life vehicle recovery Information on end-of-life vehicle recovery centres and the recycling of end-of-life vehicles is available on our website.
Vehicle care 137 Pull the release lever and return it to its original position. Lift the safety catch upwards and open the bonnet. Air intake 3 109. Secure the bonnet support. Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch.
138 Vehicle care When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend to use the same engine oil that is filled in. The engine oil level must not exceed the MAX mark on the dipstick. Caution Overfilled engine oil must be drained or suctioned out.
Vehicle care 139 concentration checked and have the cause of the coolant loss remedied by a workshop. Washer fluid Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. Brakes A squealing noise indicates that the brake lining is at its minimum thickness.
140 Vehicle care Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point. Laying up the vehicle for more than 4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery.
Vehicle care 141 Wiper blades on the windscreen Lift the wiper arm, tilt wiper blade at a 90° angle to the wiper arm and remove to the side. Wiper blade on the rear window Lift wiper arm. Disengage wiper blade as shown in illustration and remove. Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors.
142 Vehicle care system reservoir filler neck from above. Washer fluid may escape if the reservoir is full to the top. Halogen headlights Headlights have separate systems for low beam 1 (outer bulbs) and high beam 2 (inner bulbs). Low beam 1. Disengage wire clip and remove protective cover 1 .
Vehicle care 143 High beam 1. Rotate protective cover 2 anticlockwise and remove. 2. Detach wiring plug from bulb. 3. Disengage spring clip from retainer by moving and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses.
144 Vehicle care 2. Withdraw side light bulb holder from reflector. 3. Remove bulb from socket and renew bulb. 4. Insert holder in reflector. Install the protective cover. Adaptive forward lighting Headlights have separate systems for low beam 1 (outer bulbs) and high beam 2 (inner bulbs).
Vehicle care 145 2. Press base upwards and remove from reflector. 3. Detach plug connector from bulb. 4. Insert new bulb in reflector so that the locating tab of the bulb holder aligns with the reflector recess. Attach the bulb holder so that the locating tab is on the side.
146 Vehicle care 3. Disengage spring clip from retainer by moving and swivelling to the side. 4. Remove bulb from reflector housing. 5. When installing the new bulb, insert lugs in the reflector recesses. 6. Install spring clip, plug connector onto bulb.
Vehicle care 147 Side lights 1. Rotate protective cover 2 anticlockwise and remove. 2. Withdraw side light bulb holder from reflector. 3. Remove bulb from socket and renew bulb. 4. Insert holder in reflector. Install the protective cover. Fog lights Have bulbs replaced by a workshop.
148 Vehicle care 2. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. 3. Insert bulb holder in reflector, rotate clockwise to engage. Tail lights 5-door Hatchback 1. Open side cover. 2. Remove plug connector by pressing on bulb holder tab.
Vehicle care 149 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder. 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. Tail light ( 1 ) Reverse light ( 2 ) Turn signal light ( 3 ) Tail light/brake light ( 4 ) Rear fog light, may be only on one side ( 5 ) 7.
150 Vehicle care 3-door Hatchback, van 1. Open side cover. 2. Remove plug connector by pressing on bulb holder tab. 3. Hold bulb housing from the outside; unscrew two retaining nuts. 4. Remove tail light assembly. 5. Gently press the three locking lugs on the outside of the bulb holder outwards and remove bulb holder.
Vehicle care 151 6. Push bulb into socket slightly, rotate anti-clockwise, remove and renew bulb. Reverse light (right side), rear fog light (left side) ( 1 ) Tail light ( 2 ) Turn signal light ( 3 ) Tail light/brake light ( 4 ) Tail light ( 5 ) 7. Engage bulb holder in bulb housing, ensuring that it properly engages.
152 Vehicle care 2. Remove bulb housing downwards, taking care not to pull on the cable. 3. Lift flap and disconnect wiring plug from bulb holder. 4. Rotate bulb holder anti-clockwise to disengage. 5. Remove bulb from holder and renew bulb. 6. Insert bulb holder in bulb housing and rotate clockwise.
Vehicle care 153 Front courtesy light, reading lights 1. Disengage lens, press it downward slightly and remove at a downward angle. 2. Remove bulb and renew. 3. Engage lens. Rear courtesy light and reading lights Have bulbs replaced by a workshop. Glovebox light, foot well light 1.
154 Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are three fuse boxes in the vehicle: ■ in the front left of the engine compartm.
Vehicle care 155 No. Circuit 1 Starter 2 Air conditioning system 3 Diesel fuel filter heater 4 Horn 5 Manual transmission automated, automatic transmission 6 Engine control unit 7 Fog lights 8 Engine .
156 Vehicle care No. Circuit 30 Air conditioning system 31 Power window (left) 32 Power window (right) 33 Heated exterior mirrors 34 – 35 – Instrument panel fuse box The fuse box is behind the the light switch. Pull the top edge of the panel and fold down.
Vehicle care 157 No. Circuit 10 Electrical power steering 11 Light switch, brake light 12 ABS, brake light 13 Heated steering wheel 14 Parking assist, rain sensor, interior mirror Load compartment fuse box The fuse box is on the left side of the load compartment behind a cover.
158 Vehicle care Vehicle tools Tools To open the compartment, disengage the cover and open it. Vehicles with spare wheel The jack and the vehicle tools are in the right-hand compartment in the load compartment.
Vehicle care 159 Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
160 Vehicle care Driving with a damaged tyre A loss in tyre pressure is indicated by the deflation detection system. If a tyre has no pressure, continued driving is possible ■ at a speed of max. 80 km/h (50 mph) ■ up to a distance of 80 km (50 miles) 9 Warning The vehicle will be more difficult to steer and handle.
Vehicle care 161 9 Warning If the pressure is too low, this can result in considerable tyre warm- up and internal damage, leading to tread separation and even to tyre blow-out at high speeds. Tyre deflation detection system The tyre deflation detection system continually checks the rotation speed of all four tyres.
162 Vehicle care Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogram the speedometer and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
Vehicle care 163 Tyre damage exceeding 4 mm or that is at tyre's sidewall near the rim cannot be repaired with the tyre repair kit. 9 Warning Do not drive faster than 80 km/h (50 mph). Do not use for a lengthy period. Steering and handling may be affected.
164 Vehicle care 3. Position the sealant bottle on the bracket. Make sure that the bottle does not fall. 4. Unscrew valve cap from defective tyre. 5. Screw tyre inflation hose to valve. 6. Screw air hose onto compressor connection. 7. Switch on ignition.
Vehicle care 165 12. Push catch on bracket to remove sealant bottle from bracket. Screw tyre inflation hose to free connection of sealant bottle. This prevents sealant from escaping. Stow tyre repair kit in load compartment. 13. Remove any excess sealant using a cloth.
166 Vehicle care Wheel changing Some vehicles are equipped with a tyre repair kit instead of a spare wheel 3 162. Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position.
Vehicle care 167 3. Ensure the jack is positioned correctly with the vehicle jacking points. With versions of the Corsa VXR with sill panelling or retrofitted sill panelling no jack must be used.
168 Vehicle care Spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel. The spare wheel can be classified as a temporary spare wheel depending on the size compared to the other mounted wheels and country regulations. The spare wheel has a steel rim.
Vehicle care 169 Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle.
170 Vehicle care 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible. Route the leads so that they cannot catch on rotating parts in the engine compartment.
Vehicle care 171 The towing eye is stowed with the vehicle tools 3 158. The towing eye is located in a recess. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye.
172 Vehicle care Disengage cap at bottom and remove downwards. The towing eye is stowed with the vehicle tools 3 158. Screw in the towing eye as far as it will go until it stops in a horizontal position. The lashing eye at the rear underneath the vehicle must never be used as a towing eye.
Vehicle care 173 window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover.
174 Vehicle care Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating.
Service and maintenance 175 Service and maintenance General information ................... 175 Scheduled maintenance ............ 177 Recommended fluids, lubricants and parts .
176 Service and maintenance Display of remaining distance: 1. Switch off ignition. 2. Briefly press the trip odometer reset button. The odometer reading is shown. 3. Press and hold the reset button for approx. 2 seconds. InSP and the remaining distance are displayed.
Service and maintenance 177 Scheduled maintenance Service schedules Service schedule Service operations by year 1) km (x 1000) 1) miles (x 1000) 1) 1 30 20 2 60 40 3 90 60 4 120 80 5 150 100 Check vis.
178 Service and maintenance Service operations by year 1) km (x 1000) 1) miles (x 1000) 1) 1 30 20 2 60 40 3 90 60 4 120 80 5 150 100 Replace air cleaner insert Every 4 years / 60,000 km / 40,000 mls .
Service and maintenance 179 Service operations by year 1) km (x 1000) 1) miles (x 1000) 1) 1 30 20 2 60 40 3 90 60 4 120 80 5 150 100 Check exterior of body/underbody corrosion protection and note any.
180 Service and maintenance Service operations by year 1) km (x 1000) 1) miles (x 1000) 1) 1 30 20 2 60 40 3 90 60 4 120 80 5 150 100 Undo wheel fastening (take care if tyre pressure monitoring system is present) and tighten to torque: 110 Nm. The wheel bolt taper should be greased or oiled lightly during assembly.
Service and maintenance 181 + : Additional operations. o : Under extreme operating conditions and if required by country-specific conditions, the intervals are reduced.
182 Service and maintenance Additional servicing Additional operations + Additional operations are not required every service but can be performed in conjunction with a regular service. Time allowances for such work are not included in the scope of regular services and will be charged for additionally.
Service and maintenance 183 GM = General Motors Europe LL = Longlife A or B = Engine oil quality specification 025 = Validity index Engine oil meets classifications GM-LL-A-025 and GM-LL-B-025 and is therefore suitable for both petrol and diesel engines.
184 Technical data Technical data Vehicle identification .................. 184 Vehicle data ............................... 186 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data 185 Information on identification plate: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating 5 = Permissible gross tr.
186 Technical data Vehicle data Engine data Sales designation 1.0 1.2 1.4 1.6 1.6 VXR Engine identifier code Z10XEP Z12XEP Z14XEP Z16LEL Z16LER Number of cylinders 3 4 4 4 4 Piston displacement [cm 3 .
Technical data 187 Sales designation 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.7 CDTI Engine identifier code Z13DTJ Z13DTI Z13DTH Z13DTR Z17DTR Number of cylinders 4 4 4 4 4 Piston displacement [cm 3 ] 12.
188 Technical data Performance 5-door Hatchback Engine Z10XEP Z12XEP Z14XEP Z16LEL Z13DTJ Maximum speed 3) [km/h] ([mph]) Manual transmission 150 (93) 168 (104) 173 (107) 210 (130) 163 (101) Manual tr.
Technical data 189 3-door Hatchback Engine Z10XEP Z12XEP Z14XEP Z16LEL Z16LER Z13DTJ Maximum speed 3) [km/h] ([mph]) Manual transmission 150 (93) 168 (104) 173 (107) 210 (130) 225 (140) 163 (101) Manu.
190 Technical data Van Engine Z10XEP Z12XEP Z13DTJ Z13DTI Z13DTR Z13DTH Maximum speed 3) [km/h] ([mph]) Manual transmission 150 (93) 168 (104) 163 (101) 4) 4) 172 (107) Manual transmission automated .
Technical data 191 Engine Z13DTJ ECO Z13DTI Z13DTR Z13DTH Z17DTR urban [l/100 km] 5.3/–/–/– 5) 5) 6.3/–/6.1/– 6.3/–/–/–/ extra-urban [l/100 km] 3.4/–/–/– 5) 5) 4.1/–/4.1/– 4.1/–/–/–/ total [l/100 km] 4.1/–/–/– 5) 5) 4.
192 Technical data Engine Z13DTJ Z13DTJ ECO Z13DTI Z13DTR Z13DTH Z17DTR urban [l/100 km] 5.7/–/–/– 5.3/–/–/– 5) 5) 6.3/–/6.1/– 6.2/–/–/–/ extra-urban [l/100 km] 3.8/–/–/– 3.4/–/–/– 5) 5) 4.1/–/4.1/– 4.0/–/–/–/ total [l/100 km] 4.
Technical data 193 Vehicle weight Kerb weight, 5-door Hatchback, basic model Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning/climate.
194 Technical data Kerb weight, 3-door Hatchback, basic model Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning/climate control [kg] Z.
Technical data 195 Kerb weight, van, basic model Corsa Engine Manual transmission Manual transmission automated Automatic transmission without/with air conditioning/climate control [kg] Z10XEP 1125/11.
196 Technical data Vehicle dimensions 5-door Hatchback 3-door Hatchback VXR Van Length [mm] 3999 3999 4040 3999 Width without exterior mirrors [mm] 1737 1713 1713 1713 Width with two exterior mirrors .
Technical data 197 Capacities Engine oil Engine Z10XEP Z12XEP, Z14XEP Z16LEL, Z16LER Z13DTJ, Z13DTH Z13DTI, Z13DTR Z13DTJ ECO Z17DTR including Filter [l] 3.
198 Technical data Tyre pressures Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) Z10XEP 185/70 R14, 200/2.
Technical data 199 Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) Z12XEP, Z14XEP 185/70 R14, 200/2.
200 Technical data Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) Z16LEL, Z16LER 195/55 R16 9) , 240/2.
Technical data 201 Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) Z13DTJ 185/70 R14 11) , 200/2.
202 Technical data Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) Z13DTI, Z13DTR, Z13DTH 185/65 R 15, 220/2.
Technical data 203 Comfort with up to 3 people ECO with up to 3 people 6) With full load Engine Tyres front rear front rear front rear [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) [ kPa/bar] (psi) 185/60 R15 7) 260/2.
204 Technical data Towing hitch installation dimensions.
Customer information 205 Customer information Vehicle data recording and privacy ....................................... 205 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
206 Index A Accessories and vehicle modifications .......................... 135 Adaptive forward lighting .......... .................................... 80, 95, 144 Additional servicing .................... 182 Adjustable air vents .................
207 D Danger, Warnings and Cautions ... 3 Daytime running lights ................. 95 Deflation detection system ........... 79 Diesel fuel system bleeding ....... 140 Diesel particle filter .................... 113 Drain diesel fuel filter ..........
208 J Jump starting ............................. 169 K Keys ............................................. 19 L Lashing eyes ............................... 63 Light switch .................................. 93 Lighting ...............................
209 Starting the engine ............ 112, 119 Steering wheel adjustment ...... 9, 66 Steering wheel controls ............... 66 Stop watch ................................... 90 Sun visors .................................... 31 Sunroof ..............
210.
Een belangrijk punt na aankoop van elk apparaat Vauxhall Corsa (2009) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vauxhall Corsa (2009) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vauxhall Corsa (2009) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vauxhall Corsa (2009) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vauxhall Corsa (2009) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vauxhall Corsa (2009) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vauxhall Corsa (2009) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vauxhall Corsa (2009) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
