Gebruiksaanwijzing /service van het product VEC049C van de fabrikant Vector
Ga naar pagina of 21
4140 S.W . 28TH W A Y • FT . LAUDERDALE, FL 33312 TEL 954.584.4446 • F AX 954.584.5556 TOLL-FREE: (866) 584-5504 OWNER’S MANUAL THIS MANUAL CONT AINS IMPORT ANT INFORMATION REGARDING SAFETY , OPERA TION, MAINTENANCE AND STORAGE OF THIS PRODUCT .
IMPORT ANT SAFETY INFORMA TION To ensure reliable ser vice, your power inverter must be installed and used properly . Please read the installation and operating instructions thoroughly prior to installation and use. Pay particular attention to the W ARNING and CAUTION statements in this manual.
CONTENTS 1.0 INTRODUCTION 1.0 Basic T our of Inver ter . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2 Back Panel . . . . . . . . . . . . . . . . . . . .
1.0 INTRODUCTION Y our new V ector MAXX SST inver ter is one in a series of the most advanced DC to AC inverters available. With proper care and appropriate usage, it will provide years of dependable ser vice in your car , truck, RV or boat.
FIGURE 1 – FRONT P ANEL FIGURE 2 – BACK P ANEL 5 1 3 2 1 3 4 2 5 1) THREE NORTH AMERICAN ST ANDARD OUTLETS 2) GREEN LED SHOWS UNIT IS OPERA TING 3) RED LED SHOWS UNIT IS SHUT DOWN 4) ON/OFF SWITCH 4 1.
MAXX SST™ inverters are ideal for powering: • TV/VCR combinations • Refrigerator/freezers • Lights • Radio receivers/transceivers •H eavy duty power tools & chargers • Stereo systems.
2.0 INVERTER APPLICA TIONS Aside from issues of supplying power to higher wattage appliances, inverters must be supplied with a constant source of high current 12VDC from a bank of batteries. At full watt load, the DC input requirements are up to 15 amps at 12VDC.
3.0 THEOR Y OF OPERA TION MAXX SST™ inverters change 12VDC into 110/120V AC RMS, electrical power . This is accomplished in two steps. (See FIGURE 4 ).
NOTE: Because of wave-shape differences, using standard digital or analog voltmeters may not correctly read the inverter output voltage. Unless a true RMS voltmeter such as a "Fluke 87" , "Fluke 8060A" , "Beckman 4410" or "T riplet 4200" is used, the reading will be from 2 to 20 volts low .
APPLIANCE AMPS@ W A TTS@ 110/120V AC 110/120V AC COMPUTER AND MONITOR 4 440 PORT ABLE V ACUUM 4.6 506 8-CUP COFFEE MAKER 5.5 605 ELECTRIC TRIMMER 5.5 605 1/2" HAMMER-DRILL 5.5 605 RECIPROCA TING SA W 6 660 V ACUUM CLEANER 7.2 792 1-1/8" ROT ARY HAMMER 7.
Inductive loads, such as TVs and stereos, require more current to operate than do resistive loads with the same wattage rating. Induction motors, as well as some TVs, may require two to six times their rated wattage to start up. Because the MAXX SST™ inverters have a peak watt power rating, many such appliances and tools may be safely operated.
Figure 6 – Batter y Operating Time For example, as shown in FIGURE 6 , using a 400 amp hour batter y (batteries), if the average power usage will be 1000 watts, the operating time will be about 150 minutes. A larger capacity batter y will deliver more operating time between recharges.
5.0 INST ALLA TION MAXX SST™ inverters will provide you with various watts of continuous, electrical power (See Models Specification Chart Page 18) when powered by a 12VDC source such as is found in a vehicle or multiple batter y configuration as shown in FIGURE 7 .
In all marine applications, DO NOT install the inverter below or near the waterline, and keep the inverter away from moisture and water . Use ONL Y non-corrosive marine fasteners and fittings for installation.
5.4 QUICK OPERA TIONAL CHECKOUT OR EMERGENCY USE YOU WILL NEED: • One heavy-duty jumper cable set with specified A WD wire rating (See Page 18) • One fully-charged automobile batter y • A common, slip joint pliers for loosening and tightening terminal nuts TEST PROCEDURE: 1.
PRELIMINARY INST ALLA TION NOTES: The inverter has four slots in its mounting bracket that allow the unit to be fastened against a bulkhead, floor , wall or other flat sur face.
9. Crimp or clamp on a heavy-duty , batter y-connection terminal to the other end of the negative (–) and positive (+) cable. Connect the negative (–) bat- ter y terminal cable to the negative (–) batter y terminal connector . 10. Ensure the inverter power switch is in the off position ( see FIGURE 1 ).
18 Maximum Continuous Power 1000 W atts 1200 W atts 1500 W atts 2000 W atts 2500 W att Surge Capacity (Peak Power) 2000 W atts 2400 W atts 3000 W atts 4000 W atts 5000 W atts No Load Current Draw (switch on) 0.6 amps 1.3 amps 1.3 amps 1.3 amps 1.8 amps Max.
7.0 SER VICE & P ARTS For ser vice on the inverters, contact the T echnical Support Depar tment at: VECTOR MANUF ACTURING, L TD 4140 S.W . 28th W ay • Ft. Lauderdale, Florida 33312 T el. (954) 584-4446 • Fax (954) 584-5556 • T oll-free: (866) 584-5504 8.
8.2 TROUBLESHOOTING GUIDE TROUBLE/ INDICA TION POSSIBLE CAUSE SUGGESTED REMEDY No AC output – DC input below Recharge or replace red LED lit 10 volts batter y No AC output – Excessive appliance Reduce load-wait for red LED lit load-thermal shutdown inverter to cool.
10. W ARRANTY VECTOR 2 YEAR LIMITED W ARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of V ector Manufacturing, Ltd., regarding this product. There is no other warranty other than those described herein.
Een belangrijk punt na aankoop van elk apparaat Vector VEC049C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vector VEC049C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vector VEC049C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vector VEC049C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vector VEC049C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vector VEC049C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vector VEC049C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vector VEC049C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
