Gebruiksaanwijzing /service van het product SC-IW van de fabrikant Velodyne Acoustics
Ga naar pagina of 60
SC- IW (In-W all) Sub w oofer SubContr actor TM Series INST ALLA TION MANUAL.
Caution! i . www .velodyne.com SC-IW Installation Manual.
A ttention! ii . www .velodyne.com SC-IW Installation Manual.
V orsic ht! iii . www .velodyne.com SC-IW Installation Manual.
A ttenzione! iv . www .velodyne.com SC-IW Installation Manual.
T able of Contents V . www .velodyne.com SC-IW Installation Manual P roduct Over view .................................................................................................1 - Driver T echnology .............................................
Product Over view 1 . www .velodyne.com SC-IW Installation Manual T he SC-IW (In-W all) subwoofer can be installed in a variety of locations and positions in any given installation.
2 . www .velodyne.com SC-IW Installation Manual T he SC-IW consists of two cabinets — the “driver module” and the “back box.” (a.k.a. the “Enclosure”). Unlike other in-wall products where a back box may be optional, the SC-IW r equires both enclosures, unaltered, for ever y installation.
T he SC-IW comes in two completely separate car tons — the SC-IWBB (Back Box) and the SC-IWDVR (Driver). Parts included with the SC-IWBB r ough install kit: • In-wall back box - Qty 1 • Mudring .
4 . www .velodyne.com SC-IW Installation Manual N ote: T his installation process assumes that the installer has access to the open framed 2x4 studded wall with 16 inch spacing. In the event that the stud spacing is larger , an additional 2x4 or other spacer can be used to fill the space between the SC-IW back box and the neighboring stud.
5 . www .velodyne.com SC-IW Installation Manual S tep 2 - Install Back Box O nce the mudring is stapled into place, the back box should be installed using eight of the phillips drive flat head screws included in the package. When installing the back box, the mudring should be aligned to the white line on the cabinet.
6 . www .velodyne.com SC-IW Installation Manual S tep 3 - Route W ire R oute the wire from the location where the electronics gear is located to where the SC-IW will be. There is "extra space" between the studs and the back box in the event that the wire has to pass along the side of the back box to the driver module.
7 . www .velodyne.com SC-IW Installation Manual S tep 5 - Finish Wall T he wall can now be finished in a traditional fashion utilizing the appropriate dr ywall thickness, standard texturing and finishing methods.
8 . www .velodyne.com SC-IW Installation Manual S tep 7 - Remove Mudring A t this point, the mudring can be removed. It should be easily removed by "pulling it through" the dr ywall opening.
9 . www .velodyne.com SC-IW Installation Manual S tep 8 - Place Clamp Rings on Driver Module R emove the two clamp rings from the packaging and place a clamp ring onto each of the bottom edges of the tubes. Note: The position of the clamp ring is critical.
10 . www .velodyne.com SC-IW Installation Manual S tep 9 - Install Driver Module I nser t the driver module assembly through the opening left in the wall by the mudring and slide the plastic tubes onto the two connection tubes The connection tubes should slide all the way down onto the surface of the driver module assembly .
11 . www .velodyne.com SC-IW Installation Manual S tep 10 - Remove Metal Grille O btain the standard grille with integrated scoop and remove the metal grille inser t, as shown, in the picture below . Note: The grille can be painted to match the de´ cor .
12 . www .velodyne.com SC-IW Installation Manual S tep 11 - Install Grille Frame I nstall the plastic grille onto the driver module using the four included machine screws. The grille hardware should easily be installed into the side of the cabinet. Tighten using the supplied allen wrench.
13 . www .velodyne.com SC-IW Installation Manual S tep 12 - Secure Grille I nstall two pan head phillips screws (provided) into standard grille into bottom left and bottom right holes.
14 . www .velodyne.com SC-IW Installation Manual S tep 13 - Install Metal Grille Insert Step 14 - Installation Complete The installation is complete. T est the installation with bass audio material and check for buzzes, rattles, and air leaks and address accordingly .
New Cons tr uction Inst allation — Designer Grille 15 . www .velodyne.com SC-IW Installation Manual N ote: T his installation process assumes that the installer has access to the open framed 2x4 studded wall with 16 inch spacing.
16 . www .velodyne.com SC-IW Installation Manual S tep 2 - Mark Installation Location M easure from the bottom (or top if the SC-IW is to fire upwards) of the designer grille’ s lowest (or highest) position 6 3/8” up along the stud and mark the stud in this location.
17 . www .velodyne.com SC-IW Installation Manual S tep 3 - Route W ire R oute the wire from the location where the electronics gear is located to where the SC-IW will be. There is "extra space" between the studs and the back box in the event that the wire has to pass along the side of the back box to the driver module.
18 . www .velodyne.com SC-IW Installation Manual S tep 4 - Secure Subwoofer to Wall A fter the location has been determined, securely fasten the subwoofer to the studs.
19 . www .velodyne.com SC-IW Installation Manual S tep 5 - Connect Speaker W ire to Subwoofer C onnect the previously routed speaker wire to the subwoofer taking care to match the positive wire to the red terminal and the negative wire to the black terminal.
20 . www .velodyne.com SC-IW Installation Manual S tep 6 - Install Filler Panel V elodyne provides an MDF filler panel to fill the distance between the driver module and the dr ywall. This filler panel also acts as a guide for the standard grille. The filler panel easily installs using the four flat head screws and included allen wrench.
21 . www .velodyne.com SC-IW Installation Manual S tep 7 - Install T emplate Place Holder C ut out the par t of the installation template that outlines the designer grille.
22 . www .velodyne.com SC-IW Installation Manual S tep 8 - Finish Wall T he wall can now be finished in a traditional fashion utilizing the appropriate dr ywall thickness, standard texturing and finishing methods.
23 . www .velodyne.com SC-IW Installation Manual S tep 10 - Install Designer Grille R emove metal grille inser t from the plastic grille and inser t into opening into the wall. The grille should then be affixed to the studs using the four included phillips drive pan head screws.
24 . www .velodyne.com SC-IW Installation Manual S tep 11 - Install Metal Insert into Plastic Grille Frame Step 12 - Finished Grille Figur e 22: Metal Inser t Installation Figur e 23: Finished Grille .
Retro-Fit Inst allation with Designer Grille 25 . www .velodyne.com SC-IW Installation Manual S tep 1 - Decide on Subwoofer Orientation and Grille Location The first decision for a retrofit installation is which way the subwoofer will face (up or down), and therefore where the designer grille will be located on the wall (near the floor or ceiling).
26 . www .velodyne.com SC-IW Installation Manual S tep 2 - Cut Out Drywall Per T emplate O nce the studs have been located, place the supplied designer grille template on the wall. After the template is secured to the wall with either staples or tape, score the dr ywall along the lines as detailed on the template.
27 . www .velodyne.com SC-IW Installation Manual S tep 3 - Remove Drywall After it is Scor ed A fter the dr ywall is scored, remove the template and the dr ywall as indicated.
28 . www .velodyne.com SC-IW Installation Manual S tep 4 - Run Speaker W ire fr om Amplifier Location to In-Wall Subwoofer R oute the wire from the location where the electronics gear is located to where the SC-IW will be.
29 . www .velodyne.com SC-IW Installation Manual S tep 5 - Assemble Cabinet and Driver Modules T ogether R emove both the back box and driver modules from the packaging and place them on a clean surface. Place the back box with the two silicon rubber tubes facing upward.
30 . www .velodyne.com SC-IW Installation Manual S tep 6 - Mark Installation Location M easure from the bottom of the cutout 6 3/8” up along the stud and mark the stud in this location. This location will determine the bottom edge of the bracket on the driver module.
31 . www .velodyne.com SC-IW Installation Manual S tep 7 - Install Subwoofer into Opening A fter the in-wall subwoofer assembly is complete, and the mounting position marked, orient the assembly inside the wall. In this installation example we have decided to face the unit downward.
32 . www .velodyne.com SC-IW Installation Manual S tep 8 - Secure Subwoofer to Wall A fter the location has been determined, securely fasten the subwoofer to the studs.
33 . www .velodyne.com SC-IW Installation Manual S tep 9 - Connect Speaker W ire to Subwoofer C onnect the previously routed speaker wire to the subwoofer taking care to match the positive wire to the red terminal and the negative wire to the black terminal.
34 . www .velodyne.com SC-IW Installation Manual S tep 10 - Install Filler Panel V elodyne provides an MDF filler panel to fill the distance between the driver module and the dr ywall. This filler panel also acts as a guide for the designer grille. The filler panel easily installs using the four flat head screws and included allen wrench.
35 . www .velodyne.com SC-IW Installation Manual S tep 11 - Install Drywall Above Filler Plate A fter the filler plate is secured to the driver module, install a replacement piece of dr ywall above the filler plate in the opening. This dr ywall should be securely fastened to the studs using dr ywall screws.
36 . www .velodyne.com SC-IW Installation Manual S tep 13 - Install Designer Grille R emove metal grille inser t from the plastic grille and inser t into opening into the wall. The grille should then be affixed to the studs using the four included phillips drive pan head screws.
37 . www .velodyne.com SC-IW Installation Manual S tep 14 - Install Metal Insert into Plastic Grille Frame Step 15 - Finished Grille Figure 36: Metal Inser t Installation Figure 37: Finished Grille In.
38 . www .velodyne.com SC-IW Installation Manual S tep 1 - Decide on Subwoofer Orientation and Grille Location The first decision for a retrofit installation is which way the subwoofer will face (up or down), and therefore where the standard grille will be located on the wall (near the floor or ceiling).
39 . www .velodyne.com SC-IW Installation Manual S tep 2 - Cut Out Drywall Per T emplate O nce the studs have been located, place the supplied standard grille template on the wall. After the template is secured to the wall with either staples or tape, score the dr ywall along the lines as detailed on the template.
40 . www .velodyne.com SC-IW Installation Manual S tep 3 - Remove Drywall After it is Scor ed A fter the dr ywall is scored, remove the template and the dr ywall as indicated.
41 . www .velodyne.com SC-IW Installation Manual S tep 4 - Run Speaker W ire fr om Amplifier Location to In-Wall Subwoofer R oute the wire from the location where the electronics gear is located to where the SC-IW will be.
42 . www .velodyne.com SC-IW Installation Manual S tep 5 - Assemble Cabinet and Driver Modules T ogether R emove both the back box and driver modules from the packaging and place them on a clean surface. Place the back box with the two silicon rubber tubes facing upward.
43 . www .velodyne.com SC-IW Installation Manual S tep 6 - Mark Installation Location M easure from the bottom of the cutout 5 3/8” up along the stud and mark the stud in this location. This location will determine the bottom edge of the bracket on the driver module.
44 . www .velodyne.com SC-IW Installation Manual S tep 7 - Install Subwoofer into Opening A fter the in-wall subwoofer assembly is complete, orientate the assembly inside the wall. In this installation example we have decided to face the unit downward.
45 . www .velodyne.com SC-IW Installation Manual S tep 8 - Secure Subwoofer to Wall A fter the location has been determined, securely fasten the subwoofer to the studs.
46 . www .velodyne.com SC-IW Installation Manual S tep 9 - Connect Speaker W ire to Subwoofer C onnect the previously routed speaker wire to the subwoofer taking care to match the positive wire to the red terminal and the negative wire to the black terminal.
47 . www .velodyne.com SC-IW Installation Manual S tep 10 - Install Filler Panel V elodyne provides an MDF filler panel to fill the distance between the driver module and the dr ywall. This filler panel also acts as a guide for the standard grille. The filler panel easily installs using the four flat head screws and included allen wrench.
48 . www .velodyne.com SC-IW Installation Manual S tep 11 - Install Drywall Above Filler Plate A fter the filler plate is secured to the driver module, install a replacement piece of dr ywall above the filler plate in the opening. This dr ywall should be securely fastened to the studs using dr ywall screws.
49 . www .velodyne.com SC-IW Installation Manual S tep 13 - Remove Metal Grille R emove the filler plate. Obtain the standard grille with integrated scoop and remove metal grille inser t, as shown, in the picture below .
50 . www .velodyne.com SC-IW Installation Manual S tep 14 - Install Grille Frame I nstall the plastic grille onto the driver module using the four included machine screws. The grille hardware should easily be installed into the side of the cabinet. Tighten using the supplied allen wrench.
51 . www .velodyne.com SC-IW Installation Manual S tep 15 - Secure Grille I nstall two pan head phillips screws (provided) into standard grille into bottom left and bottom right holes.
52 . www .velodyne.com SC-IW Installation Manual S tep 16 - Install Metal Grille Insert Step 17 - Installation Complete The installation is complete. T est the installation with bass audio material and check for buzzes, rattles, and air leaks and address accordingly .
53 . www .velodyne.com SC-IW Installation Manual Other V elodyne Subw oofer Products DD Series DD-10 DD-12 DD-15 DD-18 Digital Drive 18 12 Signature Edition DLS-R Series DLS - 3500R DLS - 3750R DLS - .
54 . www .velodyne.com SC-IW Installation Manual V elodyne Acoustics, Inc. 345 Digital Drive Morgan Hill, CA 95037 408.465.2800 voice 408.779.9227 fax 408.779.9208 ser vice fax www .velodyne.com Ser vice E - mail: ser vice@velodyne.com Product E - mail: help@velodyne.
Een belangrijk punt na aankoop van elk apparaat Velodyne Acoustics SC-IW (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Velodyne Acoustics SC-IW heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Velodyne Acoustics SC-IW vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Velodyne Acoustics SC-IW leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Velodyne Acoustics SC-IW krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Velodyne Acoustics SC-IW bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Velodyne Acoustics SC-IW kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Velodyne Acoustics SC-IW . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
