Gebruiksaanwijzing /service van het product IRHEDV32 van de fabrikant Vermont Casting
Ga naar pagina of 27
1 10003929 10003929 01/02 Rev. 0 * Installation and service must be performed by a qualified installer, service agency or your gas supplier. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
2 10003929 T ABLE OF CONTENTS Please read the Installation & Operating Instructions before using this appliance. Thank you and congratulations on your purchase of a Irving Oil fireplace. IMPORTANT - READ ALL INSTRUCTIONS AND WARNINGS CAREFULLY BEFORE STARTING INSTALLATION.
3 10003929 When the unit is installed into a woodburning fireplace, the minimum distance the mantel can be placed above the fireplace is governed by local building codes applicable to woodburning fireplaces. Consult local authorities having jurisdiction for these clearances.
4 10003929 FIREPLACE & TRIM DIMENSIONS R T Q U S V R - Fireplace opening width Q - Fireplace opening height S - Depth of insert T - Firebox width at insert depth(S) U - Firebox depth at insert bac.
5 10003929 Do not use this appliance if any part of it has been under water. Immediately call a quali- fied service technician to inspect the unit and replace any part of the control which has been under water. When purging the gas line, the front glass must be removed.
6 10003929 INSTALLATION OF TRIM SWITCH FOR RP GAS VALVES 1. Thread wire through openings on the right side of fireplace. Do not cut wire or insulation on metal edges. 2. Slide switch assembly from the back, between subframe and trim, then fasten the screw.
7 10003929 Under no circumstances should insulation be put between the damper and the top of the unit. This may cause condensation and overheating of the unit.
8 10003929 FLUE COLLAR PLATE MOVE BACK CABINET TOP FIG .4 FASTENER PLATE MAKE SURE THE FLUE COLLAR PLATE IS IN CONTACT WITH THE BACK EDGE OF THE CABINET TOP PLATE FLUE COLLAR CABINET TOP FIG.5 FASTENER PLATE MACHINE SCREW AFTER FASTENED Fig. 8 Fig. 9 Fig.
9 10003929 GLASS FRAME W OPERA TING INSTRUCTIONS GENERAL GLASS INFORMATION Only ceramic glass approved by Vermont Castings Majestic Products Company may be used for replacement on this unit. 1. The use of substitute glass will void all product warranties.
10 10003929 CERAMIC REFRACTORY INSTALLATION 1. Remove front glass. 2. Remove logs from unit. 3. Remove refractory from package Refractory are fragile and must be han- dled with care. Where at all possible, two hands should be used when handling. 4. Take centre refractory and tilt so bottom edge slides into support angle in back of fireplace.
11 10003929 L O H I Turn counterclockwise to decrease flame height. Turn clockwise to increase flame height. Fig. 18 FLAME ADJUSTMENT Flame adjustment is accomplished by rotating the Hi/Lo adjustment knob located near the centre of the gas control. (Fig.
12 10003929 1. STOP! Read the safety information above on this label. 2. Turn off all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONLY, go on to Step 4. For RN/RP appliances turn the On/Off switch to off position or set thermostat to lowest level.
13 10003929 SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 1. Spark ignitor will not light A. Defective or misaligned Using a match, light pilot. If pilot lights, turn off pilot and electrode at pilot. push the red button again. If pilot will not light - check gap at electrode and pilot-should be 1/8" to have a strong spark.
14 10003929 • GAS SUPPLY ON • SUPPLY LINE HOOKED UP • SHUTOFF VALVE OPEN NO NO NO NO • LOCKOUT HAS ENGAGED. WAIT 60 SECONDS AND TRY AGAIN. • FOR SPARK AT ELECTRODE WHILE DEPRESSING PIEZO — 1/8" GAP TO PILOT HOOD NEEDED.
15 10003929 REPLACEMENT P ARTS IRHEDV32 35 30 31 32 27 29 28 25 26 3 2 33 34 22 24 15 L O H I PILOT ADJ PILOT ON OFF 23 a/b 21 20 19 14 12 16 8 a/b 9 a/b 13 18 17 11 a/b 18 10a/b.
16 10003929 REPLACEMENT P ARTS LIST Description IRHEDV32 1 Log Set Complete 57896 1a Log Ember Front KR1 1b Log Front Left KR2 1c Log Front Right KR3 1d Log Rear KR4 1e Log Top Left KR5 1f Log Top Right KR6 2 Lava Rock (Package) 10001454 3 Burner Lava Rock (Package) 57897 4a Burner Complete With Tiles (Nat.
10003929 A-TRIM OPTIONS FOR RHEDV32 17 FRAME ASSEMBLY 1. Lay Trim Top Facing and Trim Side Facings, face down on to an even surface such as a table or floor.
10003929 Fit Decorative Frame to the fireplace and fasten (Fig. 25). Plastic on the trim must be removed before mounting onto the fireplace. Glass must be tightly pressed against the front of the frame in order to prevent screws from damaging glass edges.
10003929 KEY DESCRIPTION RHESS (2) RHESL (3) RHESSD (3) RHESLD (3) RHESXL (4) 1 Trim Frame Top, Flat Black 57929 57932 57929 57932 57935 2 Trim Frame Left, Flat Black 57927 57930 57927 57930 57933 3 T.
10003929 TRIM ASSEMBLY 1. Install trim channels (left and right sides). Use two screws to assemble each piece. 2. Slide on the trim top channel and fasten it from the back side. 3. Install the trim top deflector and use two screws to fasten it. (Fig. 26) 4.
10003929 A3) RHEF A and RHEFP TRIMS Glass Frame Louvre Note: Position brass trim top as shown (small end up) to prevent heat discolouration Fig. 27 Fig. 28 1. Remove the front glass (see "Glass Frame Re- moval" section). 2. Install support window trim channel, top and bottom brass trim by using the shortest black screw.
10003929 A4) HEBTKP , HESBTKP , HECBTK, HECBTKMB & HEBT A TRIMS HECBTK - Cast bay window and grills in classic black trim kit HECBKMB - Cast bay window and grills in midnight black porcelain ename.
10003929 1) Reposition controls. a) Remove the Fan Speed Control Box (Fig. 33). b) Attach the Fan Speed Control Box to the Bracket (Fig. 34) and install the Bracket into the Cabinet. Only for RN/RP VALVE units. c) Install the Control Knobs Extensions onto the appropriate Control Valve Knobs (Fig.
10003929 Fig. 39. Attach magnets and brass trim to the steel frame. Fig. 40. Bracket for HEBTKP. Fig. 37. Hang the Window Grille or the Steel Frame onto the lower tabs of the Hanging Brackets. Fig. 38. Engage the slots in the Upper Grille Top Louvre with the upper tabs of the Hang- ing Brackets.
10003929 (1) With magnets. IMPORTANT: Only Trim Panel Assemblies Approved by Vermont Castings Majestic Products Company Can Be Used on These Products. ALL repair parts will be available from your local dealer.
10003929 26 1. Install the unit according to Homeowner’s Manual. 2. Install the trim according to Installation Instructions. 3. Remove the two (2) screws at the bottom of the trim. 4. Install the riser at the bottom of the trim (Fig. 58). 5. Fasten the trim with the same two (2) screws removed on step 3.
10003929 8" x 12" VENT TERMINATION KIT Model: HEDVT (8" x 12") (Fit Typical 8" x 12" and 9" x 13" flue Tile) Kit Includes: A - 8" x 12" Vent Termination (x1) B - Stainless Steel Clamps 3"-3.
Een belangrijk punt na aankoop van elk apparaat Vermont Casting IRHEDV32 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vermont Casting IRHEDV32 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vermont Casting IRHEDV32 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vermont Casting IRHEDV32 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vermont Casting IRHEDV32 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vermont Casting IRHEDV32 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vermont Casting IRHEDV32 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vermont Casting IRHEDV32 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
