Gebruiksaanwijzing /service van het product VCWB300 van de fabrikant Viking
Ga naar pagina of 24
SERVICE NOTEBOOK VCWB300 PROFESSONAL MODEL BUILT-IN FULL HEIGHT WINE COOLER.
Table of Contents Technical Information--------- ----------------- --------------------------------- ---------- 4 Sealed System------------------- ----------------- --------------------------------- -.
VCWB300 DDWB300 DESIGNER – DFWB300 FULL OVERLAY BUILT-IN FULL HEIGHT WINE COOLER VIKING TECHNICAL INFORMATION * DUE TO POSSIBLITY OF PERSONAL INJURY OR PROPERTY DAMA GE, ALWAYS CONTACT AN AUTHORIZED TECHNICIAN FOR SERVICING OR REPAI R OF THIS WINE COOLER.
SEALED SYSTEM The sealed system consists of the following components (listed in order of refrigerant flow): 1 condenser coil 1 dryer assembly 3 solenoid valves 3 heat exchangers 3 evaporators 1 compressor 1 discharge tube 1 drain pan heater 1 pre-condenser loop Refrigerant Type – HFC 134a Refrigerant Charge – 7.
CONTROL PANEL ASSEMBLY The wine cooler is equipped with a control panel conveniently located in the top front of the top compartment of the wine cooler. From this point the user can operate all functions of the wine cooler’s temperature management and various electronic features.
and appropriate zone valve based upon the temp erature at the evaporator thermistor and will turn off the zone valve based up on the temperature at the cham ber thermistor. Temperature readout and setting: Pressing the zone button w ill change which ch amber is selected for adjustments.
Showroom mode: This mode, selected by closing the s howroom switch is intended to simul ate normal operation in all ways except the cooling and temperature alarm functions.
GLASS MULLION SHELF Each compartment is separated be a fixed glass shelf (“Mullion” – two per wine cooler). These glass shelves are uniquely designed such that they act not only as an insulated .
DISPLAY PANEL KEYBOARD ELECTRONIC FUNCTION DESCRIPTION Power Disconnect Switch: The power on/off switch is used to tu rn the pow er off to the wine cooler when cleaning it or changing the light tubes. The wine cooler is shipped with the power on/off switch in the on position.
DISPLAY PANEL OPERATION Keyboard Entry Tone Indicates a pad was pressed, command read and accept. Zone Pad 1. Toggle between zones for set point temperature adjustment. Pressing immediately toggles from Top to mid to bottom , respectively that order. Entry tone will sound at each depression of pad.
Display Pad 1. Activates control panel. Pressing button for 2 seconds toggles the display on/off. Entry tone will sound at after 2 seconds of pad depression. 2. Activates Holiday Mode. Pr essing button for 15 seconds toggles the holiday mode on/off. 3.
LEVELING ADJUSTMENTS DOOR STOP ADJUSTMENT 1. Using a 3/16” allen wrench, remove door stop pin located in bottom hinge. 2. The pin is factory set 110 ° . For 120 ° swing, move the pin to the utmost forward stop hole. For 90 ° swing, move the pin to the utmost rear stop hole.
DIAGNOSTIC CHECK POINTS (Rfer to Wiring Schematic on Page 19) Number DescriptionA E1 Display Board Send 1 +5Vdc 2 data signals 3 ground E2 Touch switch inputs (with switches connected), typical 1 +5VDC 2 Ground Common for measurements on E2 3 Not connected 4 When button is touched +4Vdc to +5Vdc, otherwise less than +1Vdc.
DIAGNOSTIC CHECK POINTS (con’t) E4 Thermister inputs (measured wi th thermisters disconnected). 1 to 8 3 to 4.5 VDC – TE2 (Evaporator Thermister #2) 2 to 9 3 to 4.5 VDC – TC1 (Compartment Thermister #1) 3 to 10 3 to 4.5 VDC – TE1 (Evaporator Thermister #1) 4 to 11 3 to 4.
General Information: Approved Board Certification CSA – UL Suction 0.256” + 0.005” / - 0.003” Discharge 0.194” + 0.003” / - 0.003” Process 0.256” + 0.005” / - 0.003” Mechanical Data: Low Starting Torque (LST) Lubricant Charge 6.76 fl.
THERMISTER RESISTANCE READING Using a Cup of Water (full of ice) at 32 ° F , place the Thermister in the water and you should read approximately 7353 Ω ’s.
Solenoid Valve / Evaporator Fan FEATURES: Direct acting solenoid valve, designed to shut off refrigerating medi a. MOUNTING: Vertical with coil upwards preferred. During welding the central part of the body must not exceed 100 ° C. VALVE: Medium temperature from 10 ° C to + 90 ° C.
VCWB300 WIRING SCHEMATIC 19.
VCWB300 WIRING DIAGRAM 20.
TROUBLESHOOTING GUIDE PROBLEM PO SSIBLE CAUSE CORRECTION A. Warm temperature 1. Control set too warm Check set-points. Adjust set- in all Wine storage points colder. compartments. 2. Unit in Showroom Adjust set-points and listen Mode for compressor and condenser fan operation.
TROUBLESHOOTING GUIDE (con’t) PROBLEM PO SSIBLE CAUSE CORRECTION A. Warm temperature b2 Check for continuity across In all Wine Storage the motor windings of the Compartments. inoperative fan motor (See pages 14 and 19). 8. Condenser Air / Flow Condenser Fan Fault a.
TROUBLESHOOTING GUIDE (con’t) PROBLEM PO SSIBLE CAUSE CORRECTION 5. Door Ajar a. (See page 21) 6. Evaporator Thermistor Fault. a. (See page 17) 7. Condenser Air / Con- denser Fan Fault. a. (See page 22) 8. Check Thermistors a. (See E4 checks, page 15) 9.
TROUBLESHOOTING GUIDE (con’t) PROBLEM PO SSIBLE CAUSE CORRECTION 2. Refrigerant Valve a. Initiate manual valve activation Solenoid Fault, mode on opposite valve as that Stuck Open suspected. Toggle to evaporator temp readings associated with suspected valve to verify it is closed.
TROUBLESHOOTING GUIDE (con’t) PROBLEM PO SSIBLE CAUSE CORRECTION 4. No Power from 4. Check E15 to ground (See Control Board page 14). I. Control Panel 1.
Een belangrijk punt na aankoop van elk apparaat Viking VCWB300 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Viking VCWB300 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Viking VCWB300 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Viking VCWB300 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Viking VCWB300 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Viking VCWB300 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Viking VCWB300 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Viking VCWB300 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
