Gebruiksaanwijzing /service van het product Q7 Plus van de fabrikant Vivitek
Ga naar pagina of 65
.
ii Preface Copyright ©2014 Vivitek Corporation. is a trademark of Vivitek Corporation. Other trademarks are the properties of their respective owners. V alues, weights and dimensions are approximate. Specications are subject to change without prior notice.
iii Important Safety Information Important: It is strongly recommended that you read this section carefully before using the Qumi. These safety and usage instructions that will make sure you enjoy many years of safe use of the Qumi. Keep this manual for future reference.
iv Qumi Installation Notice • Allow at least a 50cm clearance around the exhaust vent. Minimum 100mm Minimum 500mm • Make sure that the intake vents do not recycle hot air from the exhaust vent.
v Power Safety • Only use the supplied power cord. • Do not place anything on the cord. Place the cord where it will not be in the way of foot trafc. • Remove the battery from the remote control when storing or not in use for a prolonged period.
vi T able of Contents Preface .................................................................................................................. ii Chapter 1 At a Glance ................................................................ 1 Overview .....
1 Chapter 1 At a Glance Overview Front/T op/Right View Keypad Keypad See Keypad - On-Screen Display (OSD) buttons Cooling Vent Do not cover Lens Projection Lens Zoom / Focus ring Zoom / Focus the proj.
2 Rear/T op/Left View Bottom View AC In Connect the supplied power cord Audio Out Connect an audio cable to speakers or headphones Audio in (L&R) Connect the Audio in (L&R) cable from an audio.
3 Standard Accessories Along with the Qumi, the following accessories are included: Remote Control (With one 3V CR2025 battery) Standard HDMI Cable VGA Cable MHL cable Regional Power Cord WA RRAN TY D.
4 Remote Control Important: 1. Be sure nothing obstructs the path between the remote control and the Qumi. If the path between the remote control and the Qumi is obstructed, the signal can bounce off certain reective surfaces.
5 Media Player Screen The media player screen is the main interface for the Qumi Q7 Plus Series. If a USB Flash Disc is plugged in when powering on the Qumi, the media player screen appears.
6 Chapter 2 Getting Started What Y ou Need Many types of external devices and peripherals can be connected to the Qumi. External or portable music players can be connected to play music. DVD, VCD and VHS players can be connected to play movies. Camcorders and digital cameras can also be used to play videos and display photos.
7 Setting Up Qumi Connecting to an HDMI Device Connect your Qumi to an HDMI device by using an HDMI cable. USB HDMI 1 / MHL HDMI 2 VG A VIDEO AU DIO OUT L - AU DIO - R K Game Console Personal Computer Smartphone Camera Blue Ray DVD player Connecting to an MHL Device Connect your Qumi to a MHL-compatible device by using an MHL cable.
8 Inserting a USB Flash Disc Connect a USB Flash Disc to the Qumi by inserting the storage device(s) into the appropriate port. USB HDMI 1 / MHL HDMI 2 VG A VIDEO AU DIO OUT L - AU DIO - R K Connecting Video Connect audio/video devices to the Qumi by using the audio/video cable.
9 Starting and Shutting down the Qumi 1. Connect the AC power cord to the Qumi. Connect the other end of the AC power cord to a wall outlet. 2. Press the POWER button to turn on the Qumi. The Qumi splash screen displays and connected devices are detected.
10 4. Press the POWER button to turn off the Qumi. 5. When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Adjusting the Image Use the Image-zoom control (on the projector) to resize the projected image and screen size (B).
11 Setting an Access Password (Security Lock) T o prevent unauthorized use of the Qumi, you can create a password. When the access password function is enabled, the password must be entered after the Qumi has been turned on. Creating a password can be done by performing the following steps: 1.
12 6. The password conrmation menu appears when you power on the Qumi when the Security Lock is enabled. Enter the password that was created in step 5. Important: Keep the password in a safe place. Without the password, you will not be able to use the Qumi.
13 Setting Up the Remote Control The remote control comes with one (1) 3V lithium battery (CR2025). The battery is pre-installed in the remote control. T o begin using the remote control, remove the plastic tab (A) from the battery compartment. A Replacing the Remote Control Batteries 1.
14 Chapter 3 Qumi Media Suite Overview The Qumi Media Suite is designed to provide easy access to your les from an inserted USB Flash Disc. Music, movies, pictures and documents can be displayed.
15 Music Supported Formats: The music player can play music les in the following formats: • MP3 (up to 256Kbps bit-rate) • WMA, MID, MIDI, MP1, MP2, OGG, AAC, AMR, W A V , AC3, M4A, A WB, APE Playing your T rack T o open the music list, perform the following: 1.
16 The music player provides controls to navigate through a song playlist. The following table provides a description the controls. ACTION DESCRIPTION / / T oggle speaker output to Left/Right/Stereo /.
17 Movies Supported Formats The following video formats are supported: • H.264 video up to 720p at 30 frames per second; Main Prole level 3.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v , .mp4, and .mov le formats • MPEG-4 video up to 2.
18 Photos Supported Formats The photo viewer can open the following types of image les: • BMP (up to 4000 x 3000 pixels) • PNG (up to 4000 x 3000 pixels) • JPG (up to 4000 x 3000 pixels) Viewing Y our Photo When a USB Flash Disc is inserted, the Flash Disc folder icon will display in the le directory .
19 Ofce V iewer Supported Formats The document viewer in the Qumi Media Suite can open the following types of documents: • Microsoft ® Word (97-2007, .doc/.docx) • Microsoft ® PowerPoint (97-2007, .ppt/.pptx) (not support Animation and slide transitions) • Microsoft ® Excel (97-2007, .
20 Wi T urning on WiFi Insert the Q7 Plus WiFi dongle in the Qumi to surf the Web through a web browser . T o turn on WiFi, perform the following: 1. Press the ◄ or ► button to select the Wi icon in the media suite menu. 2. Press to enter Network Settings.
21 WiFi Control Interface The WiFi Setting contains the following controls: ACTION DESCRIPTION Return to Main Window . / Enable/Disable WiFi. WiFi conguration.
22 WiFi Congure The WiFi Congure setting lets you setup a dynamic (Default) or static IP connection. ACTION DESCRIPTION IP Address Congure the IP address of the projector here. Netmask Congure the subnet mask here. Gateway Congure the IP address of the default gateway here.
23 W eb browser Visiting a website 1. Plug the Q7 Plus Wi-Fi Dongle into Qumi’s USB socket. 2. Press ▲ ▼ ◄ ► on the remote control to control the cursor . See Remote Control on page 4 . 3. Use the remote control for navigation control. Press the Q icon (bottom-right) to access the address bar .
24 Wi Display Set Wi Display 1. Plug the Q7 Plus Wi-Fi Dongle into Qumi’s USB socket. 2. Set Network settings > Wi to Enabled and Wi hotspot to Enabled. 3. Press the ◄ or ► button to select the Wi Display icon in the media suite menu.
25 Settings System Options The system options menu displays the system and rmware information. The Information menu provides details about the software version. Play Mode The play mode menu displays settings for both video and music player options.
26 AutoPlay Option Use the AutoPlay Option menu to congure what the Qumi automatically plays when powered on. The following settings are available when AutoPlay is ON. • AutoPlay – T urn on or off auto play . • AutoPlay T ype – Automatically play photo or video les when powered on.
27 Chapter 4 On-Screen Display (OSD) Settings OSD Menu Controls The Qumi has an On-Screen Display (OSD) settings menu that allows you to make adjustments and changes to settings, such as display settings and audio settings. There are 3 menus within the OSD menu: • Image – V arious aspects of the image quality can be adjusted in this menu.
28 Setting the OSD Language The language that is displayed in the OSD can be changed. T o change the language in the OSD, perform the following steps: 1. Enter the OSD menu. Press the ◄ or ► button to select the Setting 1 and press . 2. Press the ▲ or ▼ button to move to the Advanced 1 menu.
29 OSD Menu Overview Use the following illustration to quickly nd a setting or determine the range for a setting. MAIN MENU SUB MENU SETTINGS Image Display Mode Presentation, Bright, Game, Movie, T.
30 MAIN MENU SUB MENU SETTINGS Settings 1 Source Reference Input Source Select (IR/Keypad) Projection Normal, Real, Ceiling, Real+Ceiling Aspect Ratio Fill, 4:3, 16:9, Letter Box, Native, 2.
31 MAIN MENU SUB MENU SETTINGS Settings 2 Auto Source Off, On No Signal Power Off (min) 0~180 Auto Power On Off, On Off, On LED Mode ECO , Normal Reset All Status Active Source Video Information LED Hours(Eco.
32 Image Menu T o access the Image menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Image menu and press .
33 Computer T o access the Computer menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move to the Computer menu and press . 4. Press the ◄ or ► button to change values for each applicable setting.
34 Advanced T o access the Advanced menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move to the Advanced menu and press . 4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced menu.
35 Color Manager T o access the Color Manager menu and adjust the settings, perform the following: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Image menu. 3. Press the ▲ or ▼ button to move the cursor up or down in the Color Manager menu and press .
36 Settings 1 Menu T o access the Settings 1 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 1 menu. 3. Press the ▲ or ▼ button to move the cursor up and down in the Settings 1 menu and press .
37 Audio T o adjust the audio settings, press to enter the Audio sub menu. ITEM DESCRIPTION V olume Press the ◄ or ► button to adjust the audio volume.
38 Advanced 1 T o adjust the advanced settings, press to enter the Advanced 1 sub menu. ITEM DESCRIPTION Language Press the ◄ or ► button to select a different localization menu. Security Lock Press the ◄ or ► button to enable or disable security lock function.
39 3D Setting T o adjust the 3D settings, press to enter the 3D Setting sub menu. ITEM DESCRIPTION 3D Press the ◄ or ► button to select Off, DLP-Link or IR. 3D Sync Invert Press the ◄ or ► button to turn 3D sync Invert on or off. 3D Format Press the ◄ or ► button to select Frame Sequential, T op / Bottom, Side by Side.
40 Advanced 2 T o adjust the advanced settings, press to enter the Advanced 2 sub menu. ITEM DESCRIPTION T est Pattern Press the ◄ or ► button to select different test pattern. H Image Shift Press the ◄ or ► button to shift the horizontal position.
41 Settings 2 Menu T o access the Settings 2 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to move the cursor up and down in the Settings 2 menu and press .
42 Reset All T o reset all of the menu items to the factory default values (except Language and Security Lock), perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Reset All menu and press .
43 Status T o see the status of the Qumi, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Status menu and press . ITEM DESCRIPTION Active Source Displays the activated source.
44 Advanced 1 T o access the Advanced 1 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Advanced 1 menu and press .
45 Advanced 2 T o access the Advanced 2 menu and adjust the settings, perform the following steps: 1. Enter the OSD menu. 2. Press the ◄ or ► button to select the Settings 2 menu. 3. Press the ▲ or ▼ button to select the Advanced 2 menu and press or ►.
46 Source Filter T o adjust the source lter , press or ► to enter the Source Filter sub menu. ITEM DESCRIPTION VGA Press the ◄ or ► button to enable or disable VGA source in auto search loop. Composite Video Press the ◄ or ► button to enable or disable Composite Video source in auto search loop.
47 Chapter 5 T aking Care of Y our Qumi Cleaning the Qumi Cleaning the Qumi to remove dust and grime will help provide trouble-free operation. Warning: 1. The Qumi should be turned off and unplugged before cleaning. Failure to do so may result in injury or damage to the system.
48 T roubleshooting Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the Qumi. If the problem remains unresolved, contact your dealer for assistance. The problem sometimes can be as simple as a wire that is not completely connected.
49 LED Error Messages ERROR CODE MESSAGES POWER BLUE BLINK TEMP BLUE BLINK Over temperature error (Inlet air ) - ON LED over temperature (Red) - 1 LED over temperature (Green) - 2 Fan 1 (Power) error .
50 Problem: The image is at with no contrast Adjust the Contrast setting in the Image menu in the OSD. Problem: The color of the projected image does not match the source image Adjust the Color T emperature and Gamma settings in the Image menu in the OSD.
51 F AQs 1. Does Qumi work with a personal computer , notebook or netbook? Y es. Use the provided VGA cable or HDMI cable. The Qumi can connect to a PC, notebook or netbook if they have an appropriate HDMI or VGA port. T o play audio, a stereo audio cable is required to connect to the Qumi’s audio port.
52 10. What type of photo formats does the QUMI support? JPEG, PNG and BMP . 1 1. How long will the LED light source in the Qumi last and can it be replaced? The Qumi does not use a typical UHP lamp. It uses a set of Light Emitting Diodes (LED) to illuminate and project images.
53 Specications MODEL Qumi Q7 Plus Series RESOLUTION HD (WXGA - 1280x800) PROJECTION DIST ANCE 0.8m~3.0m PROJECTION SCREEN SIZE (DIAGONAL) 26”~107.
54 Projection Distance vs. Projection Size Projection Distance and Size T able @WIDE IMAGE DIAGONAL (CM/INCHES) IMAGE WIDTH (CM/INCHES) IMAGE HIGH (CM/INCHES) PROJECTION DIST ANCE (CM/INCHES) 72.6 / 28.6 61.5 / 24 38.5 / 15 80 / 31 101.6 / 40 86.2 / 34 53.
55 T iming Mode T able SIGNAL RESOLUTION H-SYNC (KHZ) V -SYNC (HZ) COMPOSITE / S-VIDEO COMPONENT RGB DVI/HDMI NTSC — 15.734 60.0 O — — — P AL/SECAM — 15.625 50.0 O — — — VESA 720 x 400 37.9 85.0 — — O O 640 x 480 31.5 60.0 — — O O 640 x 480 37.
56 EDTV 480p 31.469 60.0 — O — O 576p 31.25 50.0 — O — O HDTV 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.
57 3D T iming T able The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual adjustment. 3D RESOLUTION HDMI 3D FORMA T 800 x 600 @ 120Hz O Fr.
58 Qumi Dimensions 238 mm 180 mm 40 mm 238 mm 125 T ripod Hole: :#1/4-20 Max L=0.3 inch Ceiling Mount Hole: M4xP0.7 L=8 mm (Max) 70 35 88 100 170 Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 8 mm (0.
59 Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Een belangrijk punt na aankoop van elk apparaat Vivitek Q7 Plus (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vivitek Q7 Plus heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vivitek Q7 Plus vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vivitek Q7 Plus leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vivitek Q7 Plus krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vivitek Q7 Plus bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vivitek Q7 Plus kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vivitek Q7 Plus . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
