Gebruiksaanwijzing /service van het product gr-10 van de fabrikant Volkswagen
Ga naar pagina of 26
z Engine, removing and installing z Assembly mountings z Engine and gearbox mountings, aligning z Installation notes z Removal notes z Securing engine to assembly stand z Tightening torques z Vehicles with air conditi oner, additional informati on and removal instructions Volkswagen New Beetle 1.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Technical data (Page 10-1) Special tools and equipment VW 313 Support clamp VW 540 Engine an d gearbox support 2024 A Lifting tackle 3180 Retainer (for engine code AGU) V.A.G 1202 A Workshop crane V.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-2) V.A.G 1331 Torque wrench (5-50 Nm) V.A.G 1332 Torque wrench (40-200 Nm) V.A.G 1383 A Engi ne/gearbox jack V.A.G 1921 Spring - type clip pliers T10012 Engine bracket V.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-3) Removal notes - First check whether a coded radio is fitted. If this is the case obtain the anti - theft coding. The engine is removed downward together with the gearbox.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-4) - Fasten reservoir to lock carrier.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-5) - Loosen and remove intake hose (between charge air c ooler and throttle valve control unit) at throttle valve control unit.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-6) - Disconnect fuel injectors harness connector and unclip bracket rail from fuel distributor. - Unscrew Ground wire between igniti on coil - 1 - and - 2 - .
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-7) Notes: Clutch pedal must not be depressed.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-8) - Remove inter - connecting, coolant, vacuum and intake hoses on engine. - Remove secondary air pump motor and bracket. - Disconnect all electric wire s from gearbox, alternator and starter and move clear.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-9) Continued for all vehicles - Remove protective cover for right - hand inner constant ve locity joint from engine. - Remove right - hand drive shaft and disconnect left - ha nd drive shaft at gearbox.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-10) Continued for all vehicles - Fit engine bracket T 10012 onto cylinder bl ock with a securing nut and M10 X 25/ 8.8 bolt and tighten to approx.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-11) - Unbolt gearbox side of asse mbly mounting from gearbox ca rrier at top - arrows - . - Carefully lower en gine with gearbox. - When doing this guide th e power assisted st eering pressure pipe past the gearbox.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-12) Securing engine to assembly stand When working on the engi ne, it should be se cured to the assembly stand support clamp VW 313 using the engine and gearbox bra cket VW 540.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-13) Vehicles with au tomatic gearbox - Secure torque converter agai nst "falling out" after s eparating engine from gearbox.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-14) - Secure engine to support clamp VW 313 using engine and gearbox bracket VW 540.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-15) Installation notes Installation is carried out in the reverse sequence, when doing this note the following: - Check whether the dowel sleev es for centralizing engine/ge arbox are in the cylinder block, install if necessary.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-16) - Install selector cable on gearbox, adjust if necessary: Repair Manual, Automatic Transmission 01M, Repair Group 37 Continued for all vehicles - When installing the assembly, ensure sufficient clearance to drive shafts.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-17) Continued for all vehicles - Align engine and gear box mountings Page 10 - 20 .
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-18) - Install center, left a nd right insulation trays: Repair Manual, Body - Exterior, Repair Group 50 - Install secondary air pump. Filling with coolant Page 19 - 13 - Carry out a test driv e and check DTC memory: Repair Manual, 1.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-19) Tightening torques.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-20) Engine and gearbox mountings, aligning WARNING! Before loosening the bolts th e assemblies must be secured with the spe cial tool 10 - 222A.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-21) Gearbox mounting Edges - a - and - b - must be parallel with one another.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-22) Assembly mountings Tightening torques Engine mounting 1) Replace bolts.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-23) Gearbox assembly mounting 1) Replace bolts Pendulum support 1) Replace bolts.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-24) Vehicles with air conditioner, additional information and removal instructions WARNING! The air conditioner refrigerant circuit must not be ope n ed.
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical Engine, removing and installing (Page 10-25) - Secure air conditioner compressor to towing eye so that the refr igerant hoses/pipes are not under tension. Notes: To prevent damage to bumper protect with adhesive tape.
Een belangrijk punt na aankoop van elk apparaat Volkswagen gr-10 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Volkswagen gr-10 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Volkswagen gr-10 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Volkswagen gr-10 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Volkswagen gr-10 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Volkswagen gr-10 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Volkswagen gr-10 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Volkswagen gr-10 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
