Gebruiksaanwijzing /service van het product GDC72 ML-52585 van de fabrikant Vulcan-Hart
Ga naar pagina of 16
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30501 (Rev. A, 11-95) GDC SERIES GAS DUPLEX COOKERS MODELS GDC24 ML-52581 GDC36 ML-52582 GDC48 ML-52583 GDC60 ML-.
— 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
— 3 — Installation, Operation and Care of GDC SERIES GAS DUPLEX COOKERS KEEP THESE INSTRUCTIONS FOR FUTURE USE GENERAL The GDC Series Gas Duplex Cookers combine a high efficiency gas griddle with adjustable-height, thermostat-controlled electric platens to provide fast production of grilled foods.
— 4 — INSTALLATION CODES AND STANDARDS The GDC Series Gas Duplex Cookers must be installed in accordance with: In the United States: 1. State and local codes. 2. National Fuel Gas Code ANSI Z223.1 (latest edition), available from American Gas Association, 1515 Wilson Blvd.
— 5 — Stand (Fig. 1) 1. Thread leg extension into fixed nut in griddle frame. 2. Thread adjustable leg through undershelf into leg extension. 3. Tighten both leg extension and adjustable legs. 4. If casters are furnished instead of adjustable legs, the locking swivel casters must be placed in the front.
— 6 — When test pressures are 1 / 2 psig (3.45 kPa) or less, the cooker must be isolated from the gas supply piping system by closing its individual shutoff valve. ELECTRICAL CONNECTIONS Make supply connections using insulated copper wire suitable for at least 90 ° C for the rated load.
— 7 — OPERA TION WARNING: THE DUPLEX COOKER AND ITS PARTS ARE HOT. BE CAREFUL WHEN OPERATING, CLEANING, AND SERVICING THE DUPLEX COOKER. CONTROLS (Fig. 2) Each griddle zone, one foot wide, and each platen has its own separate controls. Fig. 2 Main On-Off Switch — controls power to the pilot igniters.
— 8 — BEFORE FIRST USE The griddle plate is shipped with a protective coating. Remove this coating before cooking with griddle. Clean the griddle with a damp cloth and mild detergent. Rinse with a clean damp cloth and wipe dry. The griddle must be seasoned prior to first use.
— 9 — PREHEAT GRIDDLE CAUTION: Care must be exercised not to overheat the griddle plate by setting the thermostats well above recommended temperatures. Overheating the plate may cause plate warpage, and will carbonize any grease on the plate and cause sticking.
— 10 — After Each Use Clean the griddle with a flexible spatula or griddle scraper. Take care not to contact the platen surfaces as these can be easily scratched, shortening the life of the coating and promoting sticking. During The Day Flush the hot griddle with water and scrape with griddle scraper to reduce carbonized grease build-up.
— 11 — • DO NOT - Use grill cleaners on the platen. Life of the non-stick coating of the platen will vary depending upon the product cooked and the cooking temperature, but its life can be extended by frequent cleaning and by using care not to scratch the surface.
— 12 — Tools required: 7 / 16 socket (magnetic) 1 / 4 drive 1 / 4 drive universal joint 1 / 4 drive 6" extension 1 / 4 drive ratchet 1. Remove platen cover (Fig. 3). 2. Remove all bolts from platen. Remove platen surface. (Fig. 4) Fig. 3 Fig.
— 13 — 5. Tighten all bolts and nuts firmly (do not overtighten), with 7 / 16 wrench, in numerical order as shown in the diagram (Fig. 7). CAUTION: Overtightening can deform the aluminum material of the platen. The holes in the platen surface and the heads on the special bolts are eccentric.
— 14 — TROUBLESHOOTING PROBLEM Red light won't come on when main switch is on. Red light won't go off when Main On-Off or Thermostat switch is on. Cooker fails to heat when Thermostat On-Off switch is on. Igniter stays on too long after pilot flame is established.
— 15 — PROBLEM Heat doesn't turn off; amber light is off; temperature is above thermostat setting. Heat doesn't turn off; amber light is on; temperature is above thermostat setting. Fat appears to smoke excessively. Food undercooked inside.
— 16 — FORM 30501 (Rev. A, 11-95).
Een belangrijk punt na aankoop van elk apparaat Vulcan-Hart GDC72 ML-52585 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Vulcan-Hart GDC72 ML-52585 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Vulcan-Hart GDC72 ML-52585 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Vulcan-Hart GDC72 ML-52585 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Vulcan-Hart GDC72 ML-52585 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Vulcan-Hart GDC72 ML-52585 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Vulcan-Hart GDC72 ML-52585 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Vulcan-Hart GDC72 ML-52585 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.