Gebruiksaanwijzing /service van het product 558018 van de fabrikant Wagner SprayTech
Ga naar pagina of 32
Edition 5 / 2014 0558 978L ProSpray 3.39 Model: 0558018 Original operating manual GB Operating manual ProSpray 3.39 Airless high-pressure spraying unit.
2 ProSpra y 3.39 GB Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures. Be safety conscious! 1 2 3 Never put your ngers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals.
ProSpra y 3.39 3 GB Contents Contents Page 1. Safety regulations for Airless spraying ...................................... 4 1.1 Explanation of symbols used .............................................................. 4 1.2 Electric Safety .......
4 ProSpra y 3.39 GB Safety Regulations 1. Safety regulations for Airless spraying 1.1 Explanation of symbols used This manual contains information that must be read and understood before using the equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard.
ProSpra y 3.39 5 GB Safety regulations • Followmaterialandsolventmanufacturer’swarningsand instructions.Befamiliarwiththecoatingmaterial’sMSDS sheet and technical information to ensure safe use.
6 ProSpra y 3.39 GB General view of application Description of unit 2. General view of application 2.1 Application 2.2 Coating materials Processible coating materials i Pay attention to the Airless quality of the coating materials to be processed.
ProSpra y 3.39 7 GB Description of unit 10 11 1 2 3 6 8 9 7 12 5 4 13 16 15 14 17 3.3 Legend for explanatory diagram ProSpray 3.39 1 Spray gun 2 Hose to hose whip connector (3/8” x 1/2”) 3 Whip hose to gun connector (1/4” x 3/8”) 4 High pressure hose, 13 mm x 15 m (1/2” x 50 ft) 5 High pressure whip hose, 10 mm x 2.
8 ProSpra y 3.39 GB Description of unit 3.5 Technical data Voltage: 220-240VoltAC,50/60Hz Max. current consumption: 9.5A@230VAC Power cord: 3 x 1.5 mm 2 – 6 m Acceptance capacity: 1650 Watt Max. operating pressure: 221 bar (22,1 MPa) Volume ow at 12 MPa (120 bar) with water: 5.
ProSpra y 3.39 9 GB Starting operation 4. Starting operation 4.1 High-pressure hose, spray gun and separating oil 1. Screw the 15 m high-pressure hose (2) to the coating material outlet (Fig. 4, Item 1). 2. Thread the double tting into the other end of the high- pressure hose.
10 ProSpra y 3.39 GB Starting operation Solid Green When the pressure indicator is solid green, the sprayer is operating between 12 MPa (120 bar) and 23 MPa (230 bar).
ProSpra y 3.39 11 GB Starting operation 4.7 Digital Electronic Spray Control (DESC) The Digital Electronic Spray Control (DESC) increases the functionality of the sprayer. It is installed directly below the pressure control knob on the control panel. It consists of a display and four function keys.
12 ProSpra y 3.39 GB Starting operation Spraying technique Security Code Screen SECURITY CODE CHANGE-2 MENU-1 The Security Code screen allows the user to set a four digit security code to prevent unauthorizeduseofthesprayer.
ProSpra y 3.39 13 GB Handling the high-pressure hose Cleaning the unit (shutting down) 6. Handling the high-pressure hose The unit is equipped with a high-pressure hose specially suited for piston pumps. Danger of injury through leaking high-pressure hose.
8.2 Cleaning the high-pressure lter Clean the lter cartridge regularly. A soiled or clogged high-pressure lter can cause a poor spray pattern or a clogged tip. 1. Turnthepressureregulatorknobintotheblackzoneuntilit stops (no pressure).
ProSpra y 3.39 15 GB Remedy in case of faults Digital Electronic Spray Control (DESC) Error Messages The following error message screens appear whenever the Digital Electronic Spray Control (DESC) detects a problem with the sprayer. Once a problem occurs and the error message appears, the sprayer will shut down.
16 ProSpra y 3.39 GB Servicing Repairs at the unit 10. Servicing 10.1 General servicing Servicing of the unit should be carried out once annually by the WAGNER service. 1. Check high-pressure hoses, device connecting line and plug for damage. 2. Check the inlet valve, outlet valve and lter for wear.
ProSpra y 3.39 17 GB Repairs at the unit 15. Clean all the parts with the corresponding cleaning agent. Check outlet valve housing (9), outlet valve seat (15), outlet valve ball (13) and upper ball guide (12) for wear and replace parts if necessary. If the worn outlet valve seat (15) is unused on one side, install it the other way around.
18 ProSpra y 3.39 GB Repairs at the unit 19. Insert upper packing (Fig. 17) with O-ring (1) and protruding lip (2) downward. 1 2 20. Insert upper support ring (9) on top of the upper packing (10) 21. Thread the upper seal retainer (8) into the upper housing (2).
ProSpra y 3.39 19 GB Appendix 12. Appendix 12.1 Selection of tip To achieve faultless and rational working, the selection of the tip is of the greatest importance. In many cases the correct tip can only be determined by means of a spraying test. Some rules for this: The spray jet must be even.
20 ProSpra y 3.39 GB Appendix 12.4 Airless tip table Wagner TradeTip 3 tip up to 270 bar (27 MPa) without tip Fthread(11/16-16UN) for W agner spra y guns Order no . 0289391 without tip Gthread(7/8-14UN) for Graco/T itan spray guns Order no .
ProSpra y 3.39 21 GB Appendix Application Tip marking Spray angle Bore inch / mm Spraying width mm 1) Gun lter Order no . Roof coatings 223 323 423 523 623 723 823 20° 30° 40° 50° 60° 70° 80° 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.
22 ProSpra y 3.39 GB Appendix 12.5 TempSpray The paint material is heated to the required temperature uniformly by an electric heating element, which is located inside the hose (regulated from20°Cto60°C).
ProSpra y 3.39 23 GB Appendix 12.6 Pump-Runner (Order No. 2306987) Universalaccessoriesforcleaning,cleantransportationandpreservationofthepumpunit.
24 ProSpra y 3.39 Accessories illustration ProSpray 3.39 3 1 5 8 2 4 7 9 10 6.
ProSpra y 3.39 25 Item Part No. Description 1 0296 388 Spray gun AG 08, F-thread 0296 386 Spray gun AG 08, G-thread 0502 166 Spray gun AG 14, F-thread 0502 119 Spray gun AG 14, G-thread 2 0296 441 Pol.
26 ProSpra y 3.39 Spare Parts List ProSpray 3.39 59 60 61 1 3 4 38 5 6 9 8 35 2 36 7 2 10 11 12 13 17 16 14 15 18 19 20 21 22 23 24 26 27 28 30 31 32 33 29 25 37 39 41 34 40 43 42 46 44 45 47 48 49 Ma.
ProSpra y 3.39 27 Item Part No. Description 1 0290 271 Motor shroud 2 0508 559 Screw (2) 3 0558 497 Belly pan assembly 4 9802 266 Screw (2) 5 0290 228 Door 6 0509 218 Screw (2) 7 0290 253 Grommit 8 05.
28 ProSpra y 3.39 Item Part No. Description 1 0558 419 Cylinder 2 0524 905 Stopping spacer 3 0524 906 Extension bushing 4 0558 570A Piston extension 5 0558 422 Extension slider 6 9832 126 Connecting p.
ProSpra y 3.39 29 Spare Parts List ProSpray 3.39 16 17 4 5 6 8 7 9 13 12 14 15 10 11 1 2 3 18 19 20 Drive Assembly Item Part No. Description 1 0558 572A Slider assembly 2 0507 767 Screw (4) 3 0290 272.
30 ProSpra y 3.39 15 1 2 3 4 5 7 6 8 9 17 16 18 13 14 15 12 11 10 19 20 Filter assembly Spare Parts List ProSpray 3.39 1 15 2 3 4 5 6 7 8 9 10 11 12 13 14 Item Part No.
ProSpra y 3.39 31 Important notes on product liability As a result of an EC regulation being eective as from January 1, 1990, the manufacturer shall only be liable for his product if all parts come from him or are released by him, and if the devices are properly mounted and operated.
32 ProSpra y 3.39 www.wagner-group.com A J. W agner Ges.m.b.H. Ottogasse 2/20 2333 Leopoldsdorf Österreich T el. +43/ 2235 / 44 158 T elefax +43/ 2235 / 44 163 oce@wagner-group .at DK W agner Sprayt ech Scandinavia A/S Helgeshøj Allé 28 2630 T aastrup Denmark T el.
Een belangrijk punt na aankoop van elk apparaat Wagner SprayTech 558018 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Wagner SprayTech 558018 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Wagner SprayTech 558018 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Wagner SprayTech 558018 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Wagner SprayTech 558018 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Wagner SprayTech 558018 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Wagner SprayTech 558018 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Wagner SprayTech 558018 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
