Gebruiksaanwijzing /service van het product KD-11 van de fabrikant Whirlpool
Ga naar pagina of 36
I CONSUMER SERVICES TECHNICAL EDUCA TION GROUP PRESENTS KD-11 JOB AID Part No. 4322451 L 1998 WHIRLPOOL POWER CLEAN FILTER DISHWASHERS.
II WHIRLPOOL CORPORA TION ASSUMES NO RESPONSIBILITY FOR ANY REP AIRS MADE ON OUR PRODUCTS BY ANYONE OTHER THAN AUTHORIZED SERVICE TECHNICIANS. © 1998 Whirlpool Corporation, Benton Harbor, MI 49022 CO RP O R A T IO N INTRODUCTION This Job Aid, “1998 WHIRLPOOL POWER CLEAN FILTER DISHWASHERS ,” (Part No.
III TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II TABLE OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . III SECTION ONE THEORY OF OPERATION Console Configuration .
IV.
1 Section One THEORY OF OPERATION 1998 POWER CLEAN FILTER MODELS Console Configuration Model DU910PFG Models DP920PFG, DU920PFG Model GU940SCG Model GU960SCG Model GU980SCG.
2 1. Once the tub has filled with hot water the motor begins to rotate forcing the water up through the pump chamber and out through the spray arms. Two spray jets on the underside of the lower spray arm direct water down onto the fine mesh screen of the pump housing to clear soils that may collect there during the wash cycle.
3 COMPONENT LOCATION TIMER LATCH ASSEMBLY FILL VALVE MOTOR RELAY FLOAT SWITCH OPERATING THERMOSTAT (Attached to bottom of pump housing) HI LIMIT THERMOSTAT PUMP AND MOTOR ASSEMBLY HEATER DETERGENT AND.
4 Removing Access and Outer Door Panels 1. Loosen but do not remove the two (2) toe panel screws below the access panel. Remove and set aside the two (2) screws above the access panel. (Fig. 2-1) 2. Remove the access panel assembly by sliding it upward to clear the loosened screws.
5 Removing the Heater Element From beneath the cabinet: 1. Remove the front access panel. (See Removing the Outer Door Panel) 2. Pull the spade connectors off the heater element terminals. 3. Unscrew the two (2) nuts securing the heater element to the bottom of the tub.
6 Servicing the Vertical Water Tube The vertical water tube in these models delivers water to the spray arm mounted underneath the upper dish rack and a smaller spray arm mounted at the top of the dishwasher tub.
7 Removing the Pump Motor Assembly 1. Unscrew and remove the nozzle cap and remove the nozzle bearing and spray arm. (Fig. 2-7) 2. Disconnect the wiring harness from the motor harness plug. 3. Rubber clamps secure the pump and motor assembly to the tub.
8 Servicing the Soil Sensing System The Soil Sensing System consists of a pressure sensitive switch connected to the dishwasher pump base. (Fig. 2-12) The system detects excessive amounts of food soil.
9 Fig. 2-15 Fig. 2-16 Dishwasher Dispenser Disassembly 1. Remove the drawbar spring. (Fig. 2-15) 2. Grasp the lower edge of the drawbar and pull it away from the panel stop. Slide the drawbar down until the draw bar holes align with the locking tabs, then remove the drawbar.
10 Fig. 2-17 Fig. 2-18 Fig. 2-19 Fig. 2-20.
11 TROUBLESHOOTING GUIDE Model DU910PFG PRECAUTIONS TO BE OBSERVED WHILE TROUBLESHOOTING Always check wiring harness and connectors before initiating any test procedures. Disconnect electric power from the dishwasher before touching the printed circuit boards or re-seating wire connectors.
12 PROBLEM POSSIBLE CAUSES CORRECTION/TEST Dishwasher does not run or stops during a cycle Dishwasher will not fill Dishwasher will not drain Dishwasher will not dry dishes 1. Door is not latching properly. 2. Child lock is "ON". 3. Wash Cycle not set properly.
13 COMPONENT TESTING PRECAUTIONS TO BE OBSERVED WHILE DIAGNOSING PROBLEM COMPONENTS Disconnect electric power from the dishwasher. Voltage checks should be made by inserting meter probes beside the wires in the connector blocks with the electric power source on and the connector block plugged in.
14 COMPONENT SCHEMATIC TESTING PROCEDURE RESULTS Timer Motor Timer Dispenser Mechanism 1. Disconnect the Wiring harness connector from the timer assembly. 2. Set VOM meter on the Rx1 scale. 3. Measure resistance between timer motor terminals. 1. Disconnect the wiring harness connector from the timer assembly.
15 Wiring Diagram Cycle Timing Charts Model DU910PFG Section Four TECH TIPS.
16 Strip Circuits (DU910PFG) 5 . Heat Dry 4 . Drain 3 . Wash 1. Fill 2 . Water Heat.
17 Models DP920PFG, DU920PFG, GU940SCG, GU960SCG & GU980SCG WIRING DIAGRAM.
18 Cycle Timing Chart.
19 Note 1: Pre-Wash Sense Interval Pressure switch contact closure at any time during this interval causes the cycle to jump to interval 37. Immediately. For the normal cycle, the heater is “off” during this interval. For the heavy and pots-n-pans cycles the heater is “on” during this interval.
20 1. The diagnostics test cycle starts at interval 11 and concludes at interval 2. To initiate the diagnostics test cycle, press the following sequence of keys within 10 seconds: High Temp Wash, Air .
21 Strip Circuits (DU920PFG, DP920PFG, GU940SCG, GU960DCG, GU980SCG) 5 . Heat Dry 4 . Drain 3 . Wash 2 . Water Heat 1.Fill.
22 Removing Access and Door Panels 1. Loosen but do not remove the two (2) toe panel screws below the access panel. Re- move and set aside the two (2) screws above the access panel. (Fig. 4-1) 2. Remove the access panel assembly by slid- ing it upward to clear the loosened screws.
23 4. Pull the bottom of the outer door panel out- ward and slide it down approximately ¼” to ½”. The panel will then be free for removal. (Fig. 4-1, inset) Set the door panel aside; it will be replaced with a new custom panel. 5. Remove the existing door insulation and dis- card.
24 6. Place the access panel front side down. In- stall the metal access panel extension into the slot it the access panel by pushing down firmly until the extension snaps into place. (Fig. 4-7) 7. Remove the adhesive backing from the ac- cess panel insulation and press the insula- tion firmly into place.
25 Installing Heavy Duty Door Springs Standard door springs may need to be replaced by heavy duty springs designed to compensate for the increased weight of the door resulting from the installation of custom panels. Perform the following tests to determine whether the heavy duty springs need to be installed.
26 INSTALLING THE FLOOR MOUNTING KIT KIT CONTENTS (P/N 4378968): 2 P/N 9743463 Brackets (Fig. 4-12) 1 P/N 4378974 Instruction Sheet INSTALLATION INSTRUCTIONS 1. Loosen the two (2) screws below the access panel and remove the two (2) screws above the access panel.
27 WHIRLPOOL Dishwasher Warranty LENGTH OR W ARRANTY FULL ONE-YEAR WARRANTY FROM DATE OF PURCHASE LIMITED ONE-YEAR WARRANTY SECOND YEAR FROM DATE OF PURCHASE LIMITED FOUR-YEAR WARRANTY SECOND THROUGH .
28.
29 SERIAL PLATE LOCATOR SERIAL NUMBER DESIGNATOR SERIAL NUMBER MANUFACTURING SITE F = Findlay, OH YEAR OF MANUFACTURE G = 1997 H = 1998 WEEK OF MANUFACTURE 18 = 18th Week PRODUCT SEQUENCE NUMBER F G 1.
30 CONTACT INFORMATION For Product Specifications and Warranty Information Sources: 1-800-874-4698 For Technical Assistance: 1-800-253-2870 For Service Manuals and other Service Literature: 1-800-851-.
V.
VI CO RP O R A T IO N.
Een belangrijk punt na aankoop van elk apparaat Whirlpool KD-11 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Whirlpool KD-11 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Whirlpool KD-11 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Whirlpool KD-11 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Whirlpool KD-11 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Whirlpool KD-11 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Whirlpool KD-11 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Whirlpool KD-11 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
