Gebruiksaanwijzing /service van het product 10052270 van de fabrikant Windsor
Ga naar pagina of 33
Read these instructions before using the m achine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen Leggere attentamente queste istruzioni prima di azionare la macchina Lea .
MACHINE DATA LOG/OVERVIEW CUTTER 24V (SCE) 86037 010 02/21/0 7 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ____________________________.
TABLE OF CONTENTS CUTTER 24V (SCE) 86037 010 02/21/0 7 3 Machine Data Log/Overview. ........................ 2 Table of Contents .......................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ..............................
HOW TO USE THIS MANUAL CUTTER 24V (SCE) 86037 010 02/21/0 7 1-1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
CUTTER 24V (SCE) 86037 010 02/21/0 7 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
HAZARD INTENSITY LEVEL CUTTER 24V (SCE) 86037 010 02/21/0 7 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY LABEL LOCATION CUTTER 24V (SCE) 86037 010 02/21/0 7 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels becom e illegible, promptly replace them. CIRCUIT BREAKER DECAL 86243530 PRV NO. 500565 2% GRADE WARNING SEE MANUAL SAFETY DECAL 86252530 PRV NO.
TECHNICAL SPECIFICATIONS CUTTER 24V (SCE) 86037 010 02/21/0 7 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 1450 W Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335 AH @ 20 hr rate Scrub Brush Motors 2 X .75 hp (0.56 kW) Vacuum Motor .
TECHNICAL SPECIFICATIONS CUTTER 24V (SCE) 86037 010 02/21/0 7 3-2 ITEM MEASURE Height 45 in. (114 cm) Length with 26 in. (66 cm) scrub head 64 in. (163 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 26 in. (66 cm) scrub head 35 in.
HOW THE MACHINE WORKS CUTTER 24V (SCE) 86037 010 02/21/0 7 3-3 The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank.
COMPONENTS CUTTER 24V (SCE) 86037 010 02/21/0 7 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11.
CONTROLS CUTTER 24V (SCE) 86037 010 02/21/0 7 3-5 3 5 8 6 13 9 4 1 2 15 11 14 10 7 12.
CONTROLS CUTTER 24V (SCE) 86037 010 02/21/0 7 3- 6 1. Key Switch 2. Emergency Shut Off Switch 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Brush Lift Lever 8. Solution Control Knob 9. Vacuum Switch 10. Squeegee Lift Lever 11.
CONTROLS CUTTER 24V (SCE) 8603701 0 02/21 /07 3-7 7. BRUSH PRESSURE LEVER Adjusts the amount of brush pressure to the floor by raising or lowering the scrub deck. To apply brush pressure, lower brush pressure lever to floating position. To apply additional pressure, place leve r in restri cted position.
CONTROLS CUTTER 24V (SCE) 8603701 0 02/21 /07 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged.
MACHINE OPERATION CUTTER 24V (SCE) 86037 010 02/21/0 7 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performanc e or lost time from breakdown. Follow the same procedure each time to avoid missing steps.
MACHINE OPERATION CUTTER 24V (SCE) 8603701 0 02/21 /07 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising and lowering scrub deck/squeegee.
MACHINE OPERATION CUTTER 24V (SCE) 8603701 0 02/21 /07 3-11 DOUBLE SCRUB For floors which are heavily soiled or h ave thick accumulations of floor finish may not clean sufficiently with one pass.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after cha rging; add water if necessary * Check pad wear to preve.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-2 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Recovery Tank Float Shut-Off 6. Solution Strainer 7. Brush Motor 8. Traction Motor 9. Circuit Breakers 10. Brush Shroud & Brush Skirts 11.
MAINTENANCE CUTTER 24V (SCE) 8603701 0 02/21 /07 4-3 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-4 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to chec k the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the readi ng m ay not be accurate.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-5 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machi ne. FOR SAFETY: When charging, conn ect the charger to the batteries before conne cting the charger to the AC wall outlet.
MAINTENANCE CUTTER 24V (SCE) 8603701 0 02/21 /07 4-6 2. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squee gee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4- 7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeege e and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-8 4. SCRUB BRUSHES There are four different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-9 ! WA RNI NG 6. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protect s the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-10 ! WA RNI NG 8. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pressure only . TRACTION MOTO R CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing m achine, stop on a level surface, turn off machine and remove key.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-11 11. VACUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure washer to clean around the vacuum motors. Use tap pressure onl y. Care must be taken so that water is not directed into vacuum motor air intakes.
MAINTENANCE CUTTER 24V (SCE) 86037 010 02/21/0 7 4-12 RECOMMENDED GREASIN G: 1-2 strokes of Mobiltemp®78 or compatible clay-based or calcium-based grease.
MACHINE TROUBLESHOOTING CUTTER 24V (SCE) 86037 010 02/21/0 7 4-13 PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Wor.
MACHINE TROUBLESHOOTING CUTTER 24V (SCE) 86037 010 02/21/0 7 4-14 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set .
CUTTER 24V (SCE) 86037 010 02/21/0 7 4-15 THIS PAGE LEFT BLANK INTENTIONALLY.
Een belangrijk punt na aankoop van elk apparaat Windsor 10052270 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Windsor 10052270 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Windsor 10052270 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Windsor 10052270 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Windsor 10052270 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Windsor 10052270 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Windsor 10052270 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Windsor 10052270 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
