Gebruiksaanwijzing /service van het product LB2000IA van de fabrikant Windsor
Ga naar pagina of 31
MODELS: LB2000I LB2000IA UB2000F LB2000 10090200 10090210 10090620 10090190 HIGH SPEED BURNISHER 86309600-B 01/29/09 Operating Instructions (ENG).
MACHINE DATA LOG/OVERVIEW 86309600 (2000) B URNISHER 10/0 8/0 8 2 OVERVIEW The High Speed Burnisher is a mains powered, portable floor burnisher intended for commercial use. The appliance can be fitted with a variety of pads to perform various floor care functions.
TABLE OF CONTENTS 86309600 (2000) B URNISHER 10/0 8/0 8 3 Machine Data Log/ Overview . ............................... 2 Table of Co ntents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. ............
HOW TO USE THIS MANUAL 86309600 (2000) B URNISHER 10/0 8/0 8 1-1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
SAFETY 86309600 (2000) B URNISHER 10/0 8/0 8 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To r educe the risk of fire, electric shock, or injury: Use only indoors.
SAFETY 86315410 (BU2000) B URNISHER 1 0/0 8/08 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY 86309600 (2000) B URNISHER 10/0 8/0 8 2- 3 GROUNDING INSTUCTIONS-120V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power ci rcuit. The amp, hertz, and voltage are listed on the data label found on each machine.
SAFETY 86309600 (2000) B URNISHER 10/0 8/0 8 2-4 GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMM E RCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
SAFETY 86309600 (2000) B URNISHER 10/0 8/0 8 2 - 5 SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement.
TECHNICAL SPECIFICATIONS 86309600 (2000) B URNISHER 10/0 8/0 8 3-1 ITEM DIMENSION/CAPACIT Y Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel self adjusting handle with die cast a luminum handle housing. Motor 1.
OPERATION 86309600 (2000) B URNISHER 10/0 8/0 8 3- 2 4. Slide Bolt (item 3) through, washers (item 2), Handle Mount Brackets and Han dle Assembly as shown. Tighten bolt (item 3) and nut (item 1) until the handle cannot twist in the mount bracket (45- 50 foot pounds).
OPERATION 86309600 (2000) B URNISHER 01/29/09 3-3 CONTROLS 1. Safety Lock – Prevents unintended op eration of the machine. 2. Switch Levers – Turns machi ne on/off. OPERATION For indoor use only. When using the pad, al ways keep the machine moving when in contact with the floor.
MAINTENANCE 86309600 (2000) B URNISHER 10/0 8/08 4-1 MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Tripped circuit breaker Reset Circuit breaker tripped in building. Check and reset Fuse in motor is blown Replace CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse holder.
MAINTENANCE 86309600 (2000) B URNISHER 10/0 8/0 8 4-2 SERVICE SCHEDULE MAINTENANCE DAILY MONTHLY Check p ad wear to p revent buildu p of chemicals * Check p ad driver s y stem for dama g e * Check han.
NOTES: 86309600 (2000) B URNISHER 10/0 8/0 8 4-3.
DECK 86309600 (2000) B URNISHER 10/0 8/08 5-1 16 2 3 12 13 14 15 9 8 7 6A-B 4 5 10 11 1.
DECK 86309600 (2000) B URNISHER 10/0 8/08 5-2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86216280 140449 4 BUMPER, RUBBER 2 86217520 27918 1 COVER, FILTER BAG 3 86001390 140441 1 BAG, DUST (PACKAGE OF 10 BAGS) 4 86223430 67463 1 RETAINER, CORD 5 86276810 70738 2 SCR, M5 X .
ELECTRICAL 86309600 (2000) B URNISHER 10/0 8/0 8 5-3 1 2 3 4 5 6 7 8 9 10 11 12 13 A-C 14 A-B 15.
ELECTRICAL 86309600 (2000) B URNISHER 10/0 8/08 5-4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86136780 70801 2 SCR, M 3.5 X 40 PHTF TYPE B 2 86137290 87057 2 WASHER, M4 SHAKEPROOF 3 86224750 73993 1 SPRING, COMP, .48OD X .91L 4 86007110 72123 2 SWITCH, 25A SPST 125-250V SNAP 5 86288450 70689 1 SCR, M4.
HANDLE-LOWER 86309600 (2000) B URNISHER 10/0 8/0 8 5-5 25 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 6 8 17.
HANDLE-LOWER 86309600 (2000) B URNISHER 10/0 8/0 8 5-6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. NOTES: 1 86276810 7073 8 1 SCR, M5 X .8MM X 10 MM PPHMS BLK 2 86198450 2000 5 1 CLAMP, 5/16 NYLON.
HANDLE-UPPER 86309600 (2000) B URNISHER 10/0 8/0 8 5-7 11 8 10 9 5 7 4 13 6 12 1 2 8 10 3.
HANDLE-UPPER 86309600 (2000) B URNISHER 10/0 8/08 5-8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. NOTES: 1 86136670 70686 2 SCR, M6 X 45 SHCS BLK 2 86136680 70687 2 SCR, M6 X 50 SHCS BLK 3 86224740 73990 2 SPRING, EXT, .
MOTOR 86309600 (2000) B URNISHER 10/0 8/0 8 5-9 1 A-B 2 3 4 5 6.
MOTOR 86309600 (2000) B URNISHER 10/0 8/08 5-10 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 86312260 - 1 MOTOR, 115V 1.5HP 20000RPM LB2000, UB20000F 1B 86312250 - 1 MOTOR, 230V 1.5HP 20000RPM LB2000I, LB2000IA 2 86217490 2788 4 1 COVER, MOTOR 1.
PAD/DRIVER 86309600 (2000) B URNISHER 10/0 8/0 8 5 - 11 4 5 9 1 2 3 6 7 8.
PAD/DRIVER 86309600 (2000) B URNISHER 10/0 8/0 8 5-1 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86010720 87086 4 WASHER, M10 X 30 PLTD 2 86006920 70507 4 SCR, 3/8-16 X 3/4 HHCS PL.
WIRING-120V 86309600 (2000) B URNISHER 10/0 8/0 8 5-1 3 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86311830 - 1 WIRE, 125MM, BLK/14, 76029X76029 M -MOTOR -CB1 -SWITCH -SWITCH 1 CORD.
WIRING-230V 86309600 (2000) B URNISHER 10/0 8/0 8 5-1 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86311830 - 1 WIRE, 125MM, BLK/14, 76029X76029 M -MOTOR EMC FILTER2 EMC FI LTER -CB.
SUGGESTED SPARE PARTS 86309600 (2000) B URNISHER 10/0 8/0 8 5-15 PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES: 86224740 73990 SPRING, EXT .5OD X 3.
86309600 (2000) BURNISHER.
Een belangrijk punt na aankoop van elk apparaat Windsor LB2000IA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Windsor LB2000IA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Windsor LB2000IA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Windsor LB2000IA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Windsor LB2000IA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Windsor LB2000IA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Windsor LB2000IA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Windsor LB2000IA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
