Gebruiksaanwijzing /service van het product SCX364 van de fabrikant Windsor
Ga naar pagina of 35
Read these instructions before using the m achine MODELS: SCX364 10052410 Operating Instructions (ENG) Instrucciones de funcionamiento (SPA) 86037150 02/20/09 PRV NO.
MACHINE DATA LOG/OVERVIEW SCX364 86037150 1/17/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ___________________________________ _____.
TABLE OF CONTENTS SCX364 86037150 3/14/07 3 Machine Data Log/Overview. ........................ 2 Table of Contents ......................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ............................... 1-1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL SCX364 86037150 1/17/07 1 - 1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
SCX364 86037150 1/17/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
HAZARD INTENSITY LEVEL SCX364 86037150 1/17/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY LABEL LOCATION SCX364 86037150 1/17/07 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels becom e illegible, promptly replace them. 2% GRADE WARNING CIRCUIT BREAKER DECAL 86243530 PRV NO.
TECHNICAL SPECIFICATIONS SCX364 86037150 1/17/07 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 1440 Watts Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335AH @ 20 hr rate Scrub Brush Motors .33 hp (0.25 Kw) Vacuum Motor .75 hp (0.
TECHNICAL SPECIFICATIONS SCX364 86037150 1/17/07 3-2 ITEM MEASURE Height 45 in. (114 cm) Length with 36 in. (90 cm) scrub head 72 in. (183 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 36 in. (90 cm) scrub head 35 in. (89 cm) Width of scrub path for 36 in.
HOW THE MACHINE WORKS SCX364 86037150 1/17/07 3-3 The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended fo r commercial use. The appliance applies a clea ning solution onto a hard floor, scrubs the floo r with brushes, and then vacuum s the soiled water back into the recovery tank.
COMPONENTS SCX364 86037150 1/17/07 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain H ose 5. Scrub Head Fixed 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solu tion Stra iner 10. Rear Squeegee 11. Top Cover 12.
CONTROLS SCX364 86037150 1/17/07 3-5 4 10 11 12 14 15 8 7 6 3 13 16 1 9 5 2 17.
CONTROLS SCX364 86037150 1/17/07 3 - 6 1. Key Switch 2. Emergency Shut Off Switch (Optional) 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Actuator Switch Deck Up-Down 8. Solution Control Knob 9. Vacuu m Switch 10.
CONTROLS SCX364 86037150 1/17/07 3-7 7. ACTUATOR SWITCH DECK UP-DOWN Adjusts the amount of brush pressure to the floor by raising or lowering the scrub d eck. Use the brush pressure indicator to determin e the correct pressure. To increase brush pressure, press the bottom of the switch.
CONTROLS SCX364 86037150 1/17/07 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batterie s. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged.
MACHINE OPERATION SCX364 86037150 1/17/07 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possi ble problems that could cause poor perf ormance or lost time from breakdown. Follow the same pro cedure each time to avoid missing steps. NOTE: See maintenance section for pre-run machine inspection che cklist items.
MACHINE OPERATION SCX364 86037150 1/17/07 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The long est track is around the perimeter of the area to be cleaned. For efficient operation, the runs should b e the longest possible without turning, stopping, or raising and loweri ng scrub deck/squeegee.
MACHINE OPERATION SCX364 86037150 1/17/07 3-11 DOUBLE SCRUB For floors which are heavily soiled or h ave thick accumulations of floor finish may not clean sufficiently with one pass.
MAINTENANCE SCX364 86037150 1/17/07 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after cha rging; add water if necessary * Check pad wear to prevent buildup of.
MAINTENANCE SCX364 86037150 1/17/07 4-2 1. Batteries 2. Rear Squeegee 3. Scrub Brushes 4. Float Shut-Off 5. Solution Strainer 6. Brush Motor 5 7 2 8 4 1 11 12 9 3 10 13 6 7. Traction Motor 8. Circuit Breakers 9. Scrubhead Fixed and Swinging 10. Vacuum Motor 11.
MAINTENANCE SCX364 86037150 1/17/07 4-3 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times.
MAINTENANCE SCX364 86037150 1/17/07 4-4 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to chec k the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the readi ng m ay not be accurate.
MAINTENANCE SCX364 86037150 03/14/ 07 4-5 FOR SAFETY: When charging, conne ct the charger to the batteries before conne cting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 7 . Plug the charger connector into the battery connector.
MAINTENANCE SCX364 86037150 1/17/07 4-6 2. REAR SQUEEGEE The front blade allows solution to pass through channels in the blade into the squeeg ee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces an d can be rotated for extended life.
MAINTENANCE SCX364 86037150 1/17/07 4-7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeege e and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back.
MAINTENANCE SCX364 86037150 1/17/07 4-8 3. SCRUB BRUSHES There are four different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE SCX364 86037150 1/17/07 4-9 5. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protect s the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris.
MAINTENANCE SCX364 86037150 1/17/07 4-10 7. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pressure only . TRACTION MOTOR CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key.
MAINTENANCE SCX364 86037150 1/17/07 4-11 10. VACUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure washer to clean around the vacuum motors. Use tap pressur e only. Care must be taken so that water is not directed into vacuum motor air intakes.
MAINTENANCE SCX364 86037150 1/17/07 4-12 11. ACTUAT O R SCRUB DECK UP- DOWN REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If opti on is installed). 1. Remove front cover.
MAINTENANCE SCX364 86037150 1/17/07 4-13 13. FRONT SQUEEGEE The front blade allows solution to pass through channels in the blade into the squeeg ee assembly while maintaining vacuum to provide lift. The front blade has two wear surfac es an d can be rotated for extended life.
MAINTENANCE SCX364 86037150 1/17/07 4-14 TO ADJUST FRONT SQUEEGEE DEFLECTION 1. Choose a smooth, level surface. Lowe r the front squeegee and deck and drive forwa rd at least 2 feet (60cm) until the desired brush pressure is obtained. 2. With the squeegee down, stop the machine.
MAINTENANCE SCX364 86037150 1/17/07 4-15 RECOMMENDED GREASIN G: 1-2 strokes of Mobiltemp ® 78 or compatible clay- based or calcium-based grease..
MACHINE TROUBLESHOOTING SCX364 86037150 1/17/07 4-16 PROBLEM CAUSE SOLUTION Poor or no water pick-up on either squeegee Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debr.
MACHINE TROUBLESHOOTING SCX364 86037150 1/17/07 4-17 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set too low Turn .
Een belangrijk punt na aankoop van elk apparaat Windsor SCX364 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Windsor SCX364 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Windsor SCX364 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Windsor SCX364 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Windsor SCX364 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Windsor SCX364 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Windsor SCX364 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Windsor SCX364 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
