Gebruiksaanwijzing /service van het product SPD-J van de fabrikant Windsor
Ga naar pagina of 26
.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. 1. Use only as described in this manual.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115 volt A.C. power circuit (12OV nominal). Special voltage models are available for interna- tional applications. The amp, hertz and voltage are listed on the data label found on each machine.
CONTROLS Solution Power Cord Vat intake Filter/Screen Removable 4 Recoverv f- Main Handle Switches (see below) Solution Tank , / Accessorv Tool Water Control Switch Brush Adiustment Manifold/Jets Brush Release Knob Solution Tank Filter/Screen (inside Tank) Adjust brush to proper cleaning position by using lever located on the front of the frame.
Preparing the SPIRIT DUAL: For Hard Floor: 1.) Install the optional kit : Vac Shoe Squeegee (p/n 02285). Raise the SPD vac shoe and place the squeegee assembly over the vac shoe intake. Center the squeegee on the vac shoe and secure by tightening the two retain- ing knobs.
SPIRIT 1. Fill the solution tank. 2. Move machine to the cleaning area. 3. Lower the brush housing to the floor. 4. Adjust the brush to the desired height. 5. Plug machine into electrical outlet. 6. Release handle by pressing bar with foot. Push handle forward to lock.
15.) Ventilate the room when cleaning has been completed. Keep all traffic off the floor until it is thoroughly dry. 16.) When done cleaning for the day bring the machine to a utility sink and floor drain. Perform the daily/regular maintenance. Set the recovery tank aside so solution tank will dry.
WARNING OF POTENTIAL INJURY This product contains moving parts. To reduce the risk of injury; unplug the machine before servicing. Maintenance and repairs must be done by qualified personnel ONLY. CAUTION: Using non-Windsor parts to repair this machine will void the 6-3-1 warranty.
Periodic Maintenance: These procedures are performed by a trained service technician. The regularity of these procedures may depend on the ma- chine's use. 1.) 2.) 3.) 4.) 5.) 6.) 7.) Flush the system with a special solution to reduce scaling (alkaline build-up).
Troubleshooting Chart Condition - Corrective Action No Power To Machine: Dead electrical circuit breaker in fuse box Faulty power cord Power switch failure Faulty circuit breaker Internal wiring probl.
Troubleshooting Chart Condition Corrective Action Accessory Tool Fitting Difficult to Connect: Corrosion on fitting Floor Not Getting Clean: Severe soil conditions Floor Too Wet: Worn spray jet(s) Flo.
Servicing the Vac Motor To access the vac motor first remove the solution tank. There are (2) screws which attach the vac motor mounting bracket to the chassis. Loosen the clamp to remove the hose. To replace the motor assembly it will be necessary to remove the (3) screws which attach the motor to the vac motor mounting bracket.
6 Vac Shoe Assembly Assembly Reverse 57047 87074 05016 73181 70190 70057 89061 87008 Nut, l/4-20 Nylock Washer, 3/8 ID x .OlO Wave Arm, Vac Shoe Parallel Spacer, .259 ID x .38x .25 Scr, l/4-20 x 1/2 BHCS Scr, l/4-20 x 1 .O PHMS Weight, Vat shoe Washer.
RECOVERY & SOLUTION TANKS RECOVERY TANK Each tank has a filter screen which protects the machine ’ s internal parts from damage. Ensure that these screens are in place and clean before operating the machine.
RECOVERY & TANK ASSEMBLY Parts List RECOVERY TANK PARTS LIST; 2 87013 Washer, l/4 Flat 3 73280 Spacer, 1/4 ID x 3/8 Nylon 4 38088 Handle, Recovery Tank 5 75078 Tank, Recovery 6 14042 Bushing, 1.63 ID Snap 7 39343 Hose, 1.5 x 34 ” Vac 8 39411 Hose, 1.
Pump...Manifold...VaIve Spray Jets Rinse in hot water or use compressed air to clean. Nozzles can also be soaked in an acetic acid solution (white vinegar). CAUTION: Do not use pins or wires to clean or unclog jets. Using wires or pins to unclog jets may ruin spray pattern.
04008 56023 78156 56014 65154 Adaptor, .1/4 MPT x l/4 FPT Nipple, l/4 MPT x 1.5 Tee, l/4 FPT Nipple, l/4 Close Pump, 115V 50 PSI OPEN 70253 57081 Screw, 10-32 x 1.
HANDLE...CHASSIS...SWITCHES Ground Arrangement Vac, Brush & Pump motor ground wires See page 4 for panel configuration 18 SPD 98353 9/18/98.
HANDLE,..CHASSIS...SWITCHES Parts List 2 3 4 57104 Open 89114 Nut, 10-32 w/Star Washer Wheel, 10” 602252 5 41236 Hub Cap, Y8” Shaft 6 70249 Scr, l/4-20 x 1.
BRUSH DRIVE ASSEMBLY To access the belt remove the belt cover. To replace the belt it is necessary to loosen the motor and remove the brush. The “ preset ” belt tension is correct when the motor and belt securely back in place. Check pulley alignment and correct if necessary.
BRUSH DRIVE ASSEMBLY Parts List 2 3 4 5A 5B 5c 6 7 8 9 10 11 12 13 14 09019 70078 03089 140080 140081 140156 87146 36166 70190 73181 70201 41296 70011 87025 70020 Bearing, Brush Shoulder bolt, 5/16 OD x 3/8 L Axle, Pulley Brush, SPD Carpet Brush, SPD Hard Floor Brush, SPD Hard Floor (Grit) Washer, 1/2 ID x 1.
Vac Motor Assemblv Roller Front of frame 22.
Vac Motor 1 57022 Nut. 3/8-16 lock 2 3 4 5 6 7 8 9 10 11 12 13 14 15 57085 Nut; 3/8- 16 hex jam 03027 Axle, Roller 67082 Roller 70018 Scr, 1/4-20x 1 HHMS 73178 Spacer, Roller bracket 140077 Bracket as.
SPIRIT DUAL Squeegee Assembly 24 To attach to the SPIRIT DUAL... Raise the SPD vac shoe and install squeegee assembly over the vac shoe intake. Center the squeegee on the vac shoe and se- cure by tightening the two retaining knobs.
115V SPR WIRING DIAGRAM 98353 7/1/97 25.
LIMITED WARRANTY Windsor Industries, Inc. warrants new machines against defects in material and workmanship under normal use and service to the original purchaser.
Een belangrijk punt na aankoop van elk apparaat Windsor SPD-J (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Windsor SPD-J heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Windsor SPD-J vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Windsor SPD-J leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Windsor SPD-J krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Windsor SPD-J bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Windsor SPD-J kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Windsor SPD-J . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
