Gebruiksaanwijzing /service van het product W1668 van de fabrikant Woodstock
Ga naar pagina of 27
INSTRUCTION MANUAL MODEL W1668 13 1 ⁄ 4 " Oscillating Drill Press Phone: 1-800-840-8420 • On-Line Technical Support: tech-support@woodstockint.com COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
- 1 - Table Of Contents PAGE 1. INTRODUCTION ABOUT YOUR NEW DRILL PRESS ......................................................2 WOODSTOCK SERVICE AND SUPPORT ................................................2 WARRANTY AND RETURNS ......................
- 2 - INTRODUCTION ABOUT YOUR NEW DRILL PRESS This new Shop Fox ® Oscillating Drill Press has been specially designed by Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
- 3 - WARRANTY AND RETURNS Woodstock International, Inc. warrants all SHOP FOX ® machinery to be free of defects from workman- ship and materials for a period of 2 years from the date of original purchase by the original owner.
- 4 - READ MANUAL BEFORE OPERATING MACHINE FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY SAFETY FIRST! 1. Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine.
1. Always operate your drill press at speeds that are appropriate for the drill bit size and the mate- rial that you are drilling. 2. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off.
- 6 - 110V Operation ELECTRICAL REQUIREMENTS When it is necessary to use an extension cord, use the following guidelines: •Use cords rated for Hard Service •Never exceed a length of 100 feet •Use cords with 14 ga.
AVOIDING POTENTIAL INJURIES - 7 - Figure 2. Never drill, holding workpiece by hand. Figure 3. Keep fingers away from spinning tool. Fig. 4. Remove Switch Safety Key when not in use.
- 8 - Figure 6. Components laid out for identification. The following is a description of the components shipped with the Shop Fox ® W1668 Oscillating Drill Press. It is recommended that the components be laid out in a similar fashion to those in Figure 6 .
- 9 - ASSEMBLY While the main components of the Shop Fox ® W1668 Oscillating Drill Press are assembled at the factory, some assembly is required. The following is the recommended sequence best suited for final assembly.
- 10 - Figure 11. Lock shoe Inserted into table bracket. Figure 9. Insert the pinion gear from the inside. Figure 10. Align setscrew with flat on pinion.
- 11 - Figure 12. Hold rack in position while installing. Figure 13. Inside bevel in the correct position. Figure 14. Lock shoe in place and secured. Table Support, Cont. 4. Examine the rack and note that the gear teeth extend further on one end than the other.
- 12 - HeadStock 1. The bottom of the headstock has a pocket for inserting the column. Position the pock- et over the column, as in Figure 15. Allow the headstock to slide down until it stops (approximately 3 1 ⁄ 2 "). 2. Align the headstock directly over the foot of the base by using a plumb bob.
- 13 - Handles Three handles are supplied with your new Oscillating Drill Press. Thread them into the hub as in Figure 20. Figure 20. Spindle handle installation. Drill Chuck Figure 19. Securing drill chuck with screw. Figure 18. Jaws adjusted inside chuck body.
- 14 - Speed Change ADJUSTMENTS Unplug the drill press before changing speeds. The Oscillating Drill Press has 12 speeds ranging from 250 to 3050 RPM. There is a speed chart located under the belt guard and one on the fol- lowing page. Refer to the speed chart while reading these instructions.
- 15 - Spindle Adjustments Your new drill press comes fitted with a depth stop for use when drilling. Follow the instruc- tions below for use. 1. Loosen the depth collar lock knob. Figure 24. 2. Rotate the depth collar to the desired depth indicated by the scale on the collar.
- 16 - Oscillating Feature One of the great features of the W1668 Drill Press is its capability for oscillating sanding. The drill press can be converted from drilling opera- tions to sanding operations in just a few steps. 1. Unplug the drill press and remove the spindle handles.
- 17 - Table Adjustments The table can be adjusted to accommodate height of materials to be sanded or drilled. To adjust: 1. Loosen the table support bracket lock knob.
Always wear safety glass- es when operating drill press. Failure to comply may result in serious per- sonal injury. - 18 - OPERATIONS Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Make sure the starting switch is off.
Installing the sanding drum spindle is identical to installing a drill bit. However, it is important to install the paper and drum before installing the spindle into the drill chuck. See your local retailer for drums and paper. - 19 - Care must be taken to secure the bit firmly in the drill chuck.
- 20 - MAINTENANCE Lubrication Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. For other items on this machine, such as the quill, table and column, an occasional shot of light machine oil is all that is necessary.
- 21 - The following pages contain general machine data, parts diagrams/lists and warranty/return information for your Shop Fox ® Model W1668 Drill Press. If you need parts or help in assembling your machine, or if you need operational informa- tion, we encourage you to call our Service Department.
.
- 23 - 55 XPB07M HEX BOLT M8-1.25 X 25 56 XPB09M HEX BOLT M8-1.25 X 20 57 X1668057 PUSH ROD 58 X1668058 SPRING 59 X1668059 RUBBER WASHER 60 X1668060 OSCILLATING MECHANISM 61 X1668061 ROUND DRIVE BELT .
- 24 - NOTES:.
CUT ALONG DOTTED LINE 10. What stationary woodworking tools do you own? Check all that apply. ___Air Compressor ___Panel Saw ___Band Saw ___Planer ___Drill Press ___Power Feeder ___Drum Sander ___Radi.
TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE WOODSTOCK INTERNATIONAL, INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 Place Stamp Here.
Een belangrijk punt na aankoop van elk apparaat Woodstock W1668 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Woodstock W1668 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Woodstock W1668 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Woodstock W1668 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Woodstock W1668 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Woodstock W1668 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Woodstock W1668 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Woodstock W1668 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
