Gebruiksaanwijzing /service van het product ISM4 van de fabrikant Xantech
Ga naar pagina of 36
INSTALLATION & PROGRAMMING MANUAL ISM4 INTELLIGENT SYSTEM MANAGER.
ISM4 INSTALLATION & PROGRAMMING MANUAL 2 TABLE OF CONTENTS INTRODUCTION ............................................................................................................................... ........................ 3 ISM4 FEATURE DESCRIPTIONS .
ISM4 INSTALLATION & PROGRAMMING MANUAL 3 INTRODUCTION Congratulations and than k you for purchasing the Xantec h ISM4 Intelligent Syste m Manager. The ISM4 is the answer to the age old problem of simp ly and inexpensively keeping Home Entertainment Syst em devices in sync.
ISM4 INSTALLATION & PROGRAMMING MANUAL 4 ISM4 FEATURE DESCRIPTIONS Figure 1 – ISM4 Front Panel Features ISM4 FRONT PANEL FEATURES 1. IR Learning Eye. The IR Learning Eye allows teaching IR Com mands to the ISM4 for programming Sou r ce ON and OFF Macros and Comm and Structu res.
ISM4 INSTALLATION & PROGRAMMING MANUAL 5 Edit Mode • Solid Green – Program ON state Macro. • Solid Orange – Program OFF state Macro. • Solid Red – Program Error.
ISM4 INSTALLATION & PROGRAMMING MANUAL 6 IR Receiver and receives IR signal s from the receiver . IR signals input on this jack ca n control the ISM4 and pass through to control the individual sour ces via the Source 1-4 IR Outputs. 12. IR Control.
ISM4 INSTALLATION & PROGRAMMING MANUAL 7 When Source 1 (System Reference Device) is turned ON , the Sensor Module for t hat device will show an ON state (+12V) to the Source 1 “Sense In”. The first task that the ISM4 will take is to launch the ON Macro for Source 1.
ISM4 INSTALLATION & PROGRAMMING MANUAL 8 Figure 4 – Typical ISM4 System – AV Receiv er Triggered Home Theater/IR Rec eiver Input.
ISM4 INSTALLATION & PROGRAMMING MANUAL 9 Figure 5 – Typical ISM4 System – TV Trigge red Home Thea ter System/IR Receiver Input.
ISM4 INSTALLATION & PROGRAMMING MANUAL 10 Figure 6 – Typical ISM4 System – Multi-Zone Controller Triggered Sy stem/IR Control Input.
ISM4 INSTALLATION & PROGRAMMING MANUAL 11 SYSTEM APPLICATIONS The ISM4 is a versatile device with en dl ess possible application s. For the pu rpo se of this manual, two basic applications will be described. One i s a typical Home Theater application with the ISM4 mana ging sy stem sync for an A/V Receiver and three source com ponents.
ISM4 INSTALLATION & PROGRAMMING MANUAL 12 MULTI-ZONE A/V SYSTEM (Figure 6) The multi-zone configuration provides automatic po wer management (system sync) when used with a multi-zone system controller that does not feat ure intelligent source power ma nagement.
ISM4 INSTALLATION & PROGRAMMING MANUAL 13 INSTALLATION The ISM4 should be installed in the same gene ral locati on as the system A/V components (A/V Receiver, Multi- Zone Controller, DVD, SAT, etc).
ISM4 INSTALLATION & PROGRAMMING MANUAL 14 2. Either plug the sensor head directly into the A/V Receiv er DVD Composite Video Input or connect a shielded female to male RCA-RCA cable with gold ends to the sensor head and then to th e AV Receiver DVD Composite Video Input .
ISM4 INSTALLATION & PROGRAMMING MANUAL 15 6. Using a Xantech 10-Foot Mono Cable (Xante ch Part No 0601745 0) co nnect the Common “IR Out “ on the multi-zone controller to the IR Control Jack on the ISM4 Rear Panel . This will allow IR control of the ISM4 and pass through of IR commands from the multi-zone controller to the source d evice s.
ISM4 INSTALLATION & PROGRAMMING MANUAL 16 OTHER CONNECTIONS RS232 This Port connects to the RS232 Outpu t on a system control device such as an A/V Receiver, Multi-Zone Controller, Touch Panel, etc.
ISM4 INSTALLATION & PROGRAMMING MANUAL 17 Figure 8 ISM4 Expansion Connections 1. Using a 1-Foot Mono Cable (Xantech Part No 60174 00), connect the Expansion Jack on the Primary ISM4 to the Source 1 “Sense In” on the First Expansion ISM4 . 2. If using additional ISM4s , repeat Step 1 for each additional ISM4 as shown in Figure 8 .
ISM4 INSTALLATION & PROGRAMMING MANUAL 18 PROGRAMMING Programming the ISM4 is similar to manually program m ing a learning rem ote. All IR commands are programmed (learned) directly to the ISM4 usin g the original equi pment remotes. There is no PC or progra mming software requirement.
ISM4 INSTALLATION & PROGRAMMING MANUAL 19 PROGRAMMING MACROS The first step in programming the ISM4 is to fill out the Macro Programming Table. Th is will help keep track of what device is being programmed for which command with how much d elay in whi ch Command Structure within the Source ON or OFF Macro being pro gramm ed.
ISM4 INSTALLATION & PROGRAMMING MANUAL 20 With the ISM4 powered up and with the IR Emitters attache d to the devices to be controlled, program the ISM4 as follows: NOTE: Unless instru cted to pre ss a button for a specific duration a button pre s s sho uld be at most one full second.
ISM4 INSTALLATION & PROGRAMMING MANUAL 21 Delay – with additional Command Structures in the Macro 13. To add a delay after the IR Command in Command Structure 1 , after Step 5 , press the Delay Butto n . The ISM4 will respond by entering DELAY Learn Mode and the Program LED will flash once .
ISM4 INSTALLATION & PROGRAMMING MANUAL 22 PROGRAMMING RC68 ON/O FF TRIGGER C OMM ANDS As noted at the beginning of the Programming Section, one of the ISM4 cont rol option s has the ISM4 react to Xantech RC68 IR Commands for Discrete Power ON/OFF or Toggle Power ON/OFF control of Source 1.
ISM4 INSTALLATION & PROGRAMMING MANUAL 23 with the RC68 Toggle Command . The System Refe rence Device (Source 1) and Sources 2 -4 should all turn ON. Test OFF 6. With all sources turned ON, test the system by pointing the System Remote toward the ISM4 or connected IR Receiver and press the button with the RC68 Toggle Co mmand .
ISM4 INSTALLATION & PROGRAMMING MANUAL 24 RS232 CONTROL AND PROGRAMMING The ISM4 can be controlled via RS232 to allow powe r manage ment of the devices controlled b y the ISM4 from a PC or appropriately capabl e system controller.
ISM4 INSTALLATION & PROGRAMMING MANUAL 25 system upon detection of a change of state on any Source Sen se Input . This feature can be enabled/disa bled via the Enable/Disable Automatic Source Po wer Notification Commands exp lained in the I SM4 RS232 Command Strings Table above.
ISM4 INSTALLATION & PROGRAMMING MANUAL 26 {0/1} = Either 0 (zero) or 1 (one); 0 = OF F, 1 =ON CLONING THE ISM4 When necessary, the Macro Table (All Source O N a nd OFF Ma cr os and their contents) can be cloned from a programmed ISM4 to another ISM4.
ISM4 INSTALLATION & PROGRAMMING MANUAL 27 OPERATING THE ISM4 Once setup, there is typically no direct interactio n with the ISM4. It will automatically respond t o system conditions, IR and RS232 Command s.
ISM4 INSTALLATION & PROGRAMMING MANUAL 28 RS232 Triggered Commands Externally, the ISM4 will behave in exactly the same manner as described in the Section s: System ON Mode and System OFF Mode , when triggere d by RS232 Trigger Commands . Internally if the ISM4 ‘sees’ the RS232 Source 1 ON Command it will look at the state of Source 1 .
ISM4 INSTALLATION & PROGRAMMING MANUAL 29 APPENDIX NAVIGATING AND EDITING M AC RO S The six Front Panel Buttons each have multiple f unctions, dependi ng upon the ISM4 Mode. The following sections detail those functions within the different mo des.
ISM4 INSTALLATION & PROGRAMMING MANUAL 30 Edit Mode - Navigate Macros Press the Front Panel Prev or Next Buttons and observe the LED’s to nav igate Source ON and OFF Macros a s follows: Figure 1.
ISM4 INSTALLATION & PROGRAMMING MANUAL 31 DELAY In EDIT MODE a press of the DELAY button will cause the ISM4 to enter into DELAY Learn Mode. This will allow the programmer to program a delay within a particular IR Command Structure, even if there is no associated IR command in that Command Stru cture.
ISM4 INSTALLATION & PROGRAMMING MANUAL 32 NEXT Not used in this IR Learn Mode. PREV If not sav e of any learned IR is desired, p ress to return to Edit Mode .
ISM4 INSTALLATION & PROGRAMMING MANUAL 33 SPECIFICATIONS Dimensions 5.25 W x 2.875 D x 1.6525 H (133.35 x 73.025 x 42mm) Weight 0.76 lbs (0.34 kg) Power 2.1mm coaxial jack 12V DC @ 0.5A IR Learning Bandwidth 30KHz-100KHz Macros ON Macros 4 OFF Macros 4 Sensor Jacks 4 – Stereo 3.
ISM4 INSTALLATION & PROGRAMMING MANUAL 34 [ BLANK PAGE ].
ISM4 INSTALLATION & PROGRAMMING MANUAL 35 [ BLANK PAGE ].
ISM4 INSTALLATION & PROGRAMMING MANUAL 36 Xantech Corporation 13100 Telfair Avenue, 2/F Sylmar, CA 91342 818.362.0353 Tech Support ext. 353 www.xantech.com Installation and Programming Manual, ISM4 Intellige nt System Manage r © 2008 Xantech Corporation, Document # 0890513 6B This document is copy righ t protecte d.
Een belangrijk punt na aankoop van elk apparaat Xantech ISM4 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Xantech ISM4 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Xantech ISM4 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Xantech ISM4 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Xantech ISM4 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Xantech ISM4 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Xantech ISM4 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Xantech ISM4 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
