Gebruiksaanwijzing /service van het product 8264E van de fabrikant Xerox
Ga naar pagina of 30
1 September 2008 701P49052 8264E Color Wide Format Printer 100kg Unwinder / Winder User Guide.
.
100kg Unwinder / Winder User G uide i Table of Contents 1 Safety and Warning Label Information.................................................................. 1 1.1 Safety Cons iderations .............................................................
ii 100kg Unwinder / Winder User G uide This page has been intentionally left blank..
100kg Unwinder / Winder User G uide 1 1 Safety and Warning Label Information 1.1 Safety Considerations Various procedures throughout this user guide may list 2 levels of safety indicators that need to be adhered to during the performance of a procedu re.
1 Safety and Warning Label Information 2 100kg Unwinder / Winder User Guide 1.2.1 Warning Label Locations and Types The figures below indicate the lo cations of the warning labels. 1 1 Figure 1. Front Warning Label Locations 1 1 Figure 2. Rear Warning Label Location s No.
1 Safety and Warning Label Information 100kg Unwinder / Winder User G uide 3 1.3 Operating Instructions Labels This section explains the different types of operating instructions l abels and wher e they are located.
1 Safety and Warning Label Information 4 100kg Unwinder / Winder User Guide This page has been intentionally left blank..
100kg Unwinder / Winder User G uide 5 2 Unwinder / Winder Operation 2.1 Location of Major Components This section will explain the names and functions of the major com ponents of the Unwinder / Winder. 2.1.1 Unwinder Components 1 1 2 3 Figure 4. Location of Major Components (Unwinder) No.
2 Unwinder / Winder Operation 6 100kg Unwinder / Winder User Guide 2.1.2 Winder Components 1 1 3 2 4 Figure 5. Location of Major Components (Winder) No. Part name Function 1 Winder Spindles Rolls in the media after printing 2 Winder Tension Bar Roller Used to guide the media after printing to the r oll-in device.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 7 2.1.3 Unwinder Control Panel The Unwinder Control Panel is used to set the operating mode and to displa y the status of the Unwinder. 2 5 3 1 4 Figure 6. Unwinder Control Panel 2.1.3.
2 Unwinder / Winder Operation 8 100kg Unwinder / Winder User Guide 2.1.4 Winder Control Panel The Winder Control Panel is used to set the operati ng mode and to display the status of the Winder. 4 3 2 1 Figure 7. Winder Control Panel 2.1.4.1 Switches No.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 9 2.2 Connecting the Power Cable This section describes the procedu re for connecting the power cable. z DO NOT use a damaged power cable. If the power cable is damaged, contact your local Xerox Customer Service Representative for a replacement.
2 Unwinder / Winder Operation 10 100kg Unwinder / Winder User G uide 2.3 Turning the Power ON and OFF The following section provides procedures for setting the Unwinder / Winder power ON and OFF. 2.3.1 Turning the Power ON Turn the power ON by following the instructions below.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 11 2.4 Loading Roll Media onto the Unwinder The following section describes how to load roll media on the Unwinder. Media core size 3 inch ： Maximum media width 1625mm, Mi nimum media width 100 0mm, media outside diameter less than 250mm, weight less than 100kg.
2 Unwinder / Winder Operation 12 100kg Unwinder / Winder User G uide 4. Place the roll media on top of the rear rail. 1 2 Figure 14. Install Roll Media No. Part name 1 Rear Rail 2 Roll Media 5. Set the roll media on the Left Unwinder Sp indle and tighten the Left Unwinder Spindle Locking Handle.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 13 6. Set the roll media on the Right Unwinder Spindl e and tighten the Right Spindle Locking Handle. 3 2 1 Figure 16. Install Roll Media No. Part name 1 Right Unwinder Spindle 2 Roll Media 3 Ri ght Spindl e Locking Ha ndle 7.
2 Unwinder / Winder Operation 14 100kg Unwinder / Winder User G uide 8. Set the Printer Power Switch to ON. After an sh ort initialization period the Printer Control Panel will display “No Media”. 9. Raise the Media Set Lever. The Printer C ontrol Panel will display “Please Set Media”.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 15 11. Set the Unwinder Automatic Operation Switch as described below: ・ If the paper will be printed on the outsi de of the roll media: OUTSIDE ROLL ・ If the paper will be printed on the insi de of the roll media: INSIDE ROLL Figure 20.
2 Unwinder / Winder Operation 16 100kg Unwinder / Winder User G uide 13. Insert the roll media into the tension roller, and then into the Rear Printer Platen. Media can be inserted either with the print surf ace on the outside (Figure 22) or wi th the print surface on the inside (Figure 23).
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 17 b. When using a roll paper where the print surface is on the inside. Damage and problems that occur because of the use of roll medi a where the print surface is on the inside are not covered by the warranty.
2 Unwinder / Winder Operation 18 100kg Unwinder / Winder User G uide 14. Pull about 1 meter of roll media out from the Front Printer Plate. 1 2 Figure 24.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 19 1 2 1 Figure 26. Install Roll Media No. Part name 1 Roll Media 2 Media Setting Guide 16.
2 Unwinder / Winder Operation 20 100kg Unwinder / Winder User G uide 17 Push the “INITIALIZE” button on the Unwinder Control Panel. Figure 28. Push INITIALIZE 18 Close the Printer Front Cover.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 21 2.5 Operating the Winder This section provides instructions for using the Unwinder / Winder. 1. Set a media core on the Winder. Ensure that the si ze of the core is that same size as the media roll core.
2 Unwinder / Winder Operation 22 100kg Unwinder / Winder User G uide 4. Attached the tip of the roll m edia to the media core on the Winder Spindles. Ensure that the media parallel to the core. Secure the ti p of the media to the core with tape. 2 1 3 Figure 31.
2 Unwinder / Winder Operation 100kg Unwinder / Winder User G uide 23 2.6 Removing a Printed Media Core from the Winder This section will explain t he procedure to remove the media core from the Winder. 1. Set the Winder Automatic Operation Switch to OFF.
2 Unwinder / Winder Operation 24 100kg Unwinder / Winder User G uide This page has been intentionally left blank..
.
26 100kg Unwinder / Winder User G uide Prepared by: XEROX Corporation Global Knowledge and Language Services 800 Phillips Road, Bldg. 0218-01A Webster, New York 14580-9791 USA ©2008 by XEROX Corporation.
Een belangrijk punt na aankoop van elk apparaat Xerox 8264E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Xerox 8264E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Xerox 8264E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Xerox 8264E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Xerox 8264E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Xerox 8264E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Xerox 8264E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Xerox 8264E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
