Gebruiksaanwijzing /service van het product CRW8824SX Series van de fabrikant Yamaha
Ga naar pagina of 46
OW NER’S MA NUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUAL DE INSTRUCCIONES C D - R/RW Drive C R W 8824S X SERIES C R W 8824S X SERIES OW NER’S MA NUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUAL .
COMPLIANCE INFORMA TION ST A TEMENT (DECLARA TION OF CONFORMITY PROCEDURE) Responsible P arty: Y amaha Corporation of Amer ica Address: 6600 Or angethor pe A v e.
CA UTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure . Laser Diode Properties Material: GaAlAs Wa velength: 780-787 nm Emission Duration: Contin uous Laser Output Po wer: Less than 44.
.
i English OWNER’S MANUAL C D- R/RW Drive C R W 8824S X SERIES C R W 8824S X SERIES C D- R/RW Drive.
ii SAFETY PRECAUTIONS PLEASE READ CAREFULL Y BEFORE PROCEEDING These precautions explain how to use the device correctly and safely , thereby preventing injur y to yourself or to others.
iii CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property .
iv ■ About CD-R/RW discs Please read the follo wing regarding the handling of CD-R/R W discs. 1. Do not e xpose discs to excessiv e heat or vibrations or e xtreme cold or heat (such as in direct sunlight or near a heater). 2. Do not touch disc surf aces.
v T able of Contents Setup Flowchart .................................................................. 1 W indows Users ............................................................................... 1 Macintosh Users ................................
24X: 3,600 KB/sec Setup Flowchart These flowcharts show the pr ocedure for setting up the CR W8824SX drive. For easy cr oss-refer encing, the relevant pages in this manual ar e also given.
Setup Flowchart STEP 1 STEP 1-1 STEP 1-2 STEP 2 STEP 3 STEP 4 STEP 5 YES NO Set up the CRW8824SX drive Check that the CRW8824SX drive is recognized correctly Obtain a SCSI adapter card Install the SCS.
Introduction Features of the CRW8824SX Drive High speed CD-R/R W discs can be written/rewritten at up to 8X speed. For example, an audio CD (74 minutes/650 MB) can be created in appr oximately 10 minutes. Data reading at up to 24X speed is suppor ted.
System Configuration In or der to use the CR W8824SX drive, your computer system will need to meet the following set of requir ements. Computer The minimum system r equirements for using the CR W8824SX drive are as follows: ● For PC/A T -compatible computers: OS: W indows 95/98/98SE (Second Edition), Windows NT4.
System Configuration Software The software r equirements for using the CR W8824SX drive are as follows: ● CD writing software. This softwar e must support the CR W8824SX drive for writing to CD-R or CD-R W . n For details about how to install and use the software, r efer to the documentation that came with it.
System Configuration Discs The CR W8824SX can write to discs that carry the following logos. CD-R discs *1 The CR W8824SX can write to these discs at 8X, 6X, 4X, and 1X speeds. These discs can be played back in a CD-ROM drive or a CD player . n When writing at 8X or 6X speeds, please use “high-speed writing capable” discs.
System Configuration About CD-ROM A CD-ROM disc is a compact disc containing high-density read-only data. It has many applications, including the playback of music and video, the ar chiving of data, as well as on-line documentation.
Front and Rear of Unit Front Panel The CR W8824SX drive’ s front panel featur es the following: Manual Eject hole Only use this if no other method is available for unloading a disc. (P . 23) Disc tray The tray is used to hold the disc. It slides out from the drive unit when a disc needs to be loaded or unloaded.
Front and Rear of Unit Rear Panel The CR W8824SX drive’ s rear panel featur es the following: SCSI SCSI CDR ID TERMINA TO R LINE OUT AC I N SER. NO . st2 RL ON OFF ❋❋❋❋❋❋❋❋ 1 Serial number This consists of 3 letters and 7 digits. Y ou may need to refer to this number when requesting User Support services.
Installation This section gives a step-by-step guide to setting up your CR W8824SX drive. First Steps Before connecting your CR W8824SX drive to your computer , you need to set up the drive using the switches located at the r ear of the unit.
Installation 2 T ermination T erminators prevent SCSI signals fr om being r eflected off the last device in the chain. The SCSI terminator switch should be set to “ON” if your CR W8824SX drive is the last device on the SCSI chain. If it is not the last device on the chain, the TERMINA TOR switch should be set to “OFF .
12 Setting Up The CRW8824SX Drive There ar e three stages to setting up your CR W8824SX drive. ● Installing a SCSI adapter card Y ou will need to open the casing of your computer and insert a SCSI adapter card (sold separately) if one has not been installed alr eady .
Setting Up The CRW8824SX Drive 13 Installing a SCSI Adapter Card 1 Power down your computer and unplug it fr om the AC outlet. If you proceed without doing this, you run the risk of receiving an electric shock and/or short-circuiting and damaging components including the CR W8824SX drive.
Setting Up The CRW8824SX Drive 3 T ouch a metal part of the computer’ s chassis or power supply unit to drain any static char ge that may have built up inside your body . Drain any static charge Y ou can per manently damage equipment if you touch it while ther e is any static charge in your body .
Setting Up The CRW8824SX Drive 5 Insert your SCSI adapter car d into the slot using both hands. Make sure it is seated firmly in the slot. Then secure the car d by replacing the scr ew used for the blanking plate. Replace screw Insert SCSI adapter card 6 Attach the outer casing of the computer and any scr ews that were r emoved.
Setting Up The CRW8824SX Drive Connecting the Drive 1 Connect one end of the SCSI cable to your SCSI adapter car d. SCSI adapter card connector Connect SCSI cable 16.
Setting Up The CRW8824SX Drive The CR W8824SX drive requir es a D-sub half-pitch 50-pin pin-type connector . The connector of your SCSI adapter card may vary . Y ou will need to obtain a SCSI cable with connectors suitable for both your drive and your SCSI adapter card.
Setting Up The CRW8824SX Drive 2 Connect the other end of the SCSI cable to the r ear of your CR W8824SX drive. Either SCSI connector may be used. SCSI connector Connect SCSI cable 3 Connect the D-shaped end of the included power cable to the power connector at the rear of your CR W8824SX drive.
Setting Up The CRW8824SX Drive 4 Power up your CR W8824SX drive first, then your computer . Power ON Always power up the devices in your SCSI chain before powering up your computer . This will ensure that they are recognized by the computer’ s operating system.
Setting Up The CRW8824SX Drive Verifying the Hardware Installation Windows Users 1 When the computer’ s operating system is loading, your SCSI adapter card will be recognized and you will be pr ompted to install the drivers for it.
Setting Up The CRW8824SX Drive 3 Double-click “Y AMAHA CR W8824S” listed under “CDROM” (in Windows 95/98/98SE) and click the Settings tab. Check the “Sync data transfer” checkbox.
22 Operation This section explains how to operate the CR W8824SX drive after you have installed it. Loading a Disc 12 1 Pr ess the Eject button on the CR W8824SX drive’ s front panel. 2 Place the disc onto the tray with its label or printing facing upwar d.
Operation Manually Ejecting a Disc in an Emergency If the disc tray fails to open for some reason, such as a power outage, it can be opened manually . Manual Eject hole Paper clip Y ou should only attempt to eject a disc manually as a last resort. Malfunctions may occur if you do this too frequently .
24 T roubleshooting Please also refer to the Y AMAHA CD-R/R W Drives web site for mor e information. Y AMAHA CD-R/RW Drives web site URL: http://www .yamaha.co.jp/english/pr oduct/computer/ http://www .yamaha-yste.com/ (Eur ope) The drive does not power up.
T roubleshooting ● Are the pins and holes on the SCSI connectors straight and not defor med? Check the connectors. ● Is the terminator on the CR W8824SX drive set correctly? It should be set to ON only if it is the last device on the SCSI chain. Otherwise, it should be set to OFF .
T roubleshooting Errors occur when backing up at 6X or 8X speed fr om a separate CD- ROM drive to the CR W8824SX drive. ● A possible reason is that the CD-ROM drive is not suitable. Please use a high- speed CD-ROM drive. However , for various possible reasons, you may still encounter errors even if you ar e using a 32X or 42X speed CD-ROM drive.
27 Appendix Writing Modes Disc-at-Once (DAO) This mode is used when writing a complete disc in a single pass without pausing. Data cannot be added later , even if the full capacity of the blank disc has not been used.
Appendix Session-at-Once (SAO) As a writing method that combines the advantages of the above-mentioned “Disc- at-Once” and “T rack-at-Once,” you can combine multiple tracks into one session and write them, and then add additional data. For example, this is the writing method used to cr eate a CD EXTRA format CD.
Appendix About the Firmware The “firmware” is a small piece of softwar e built into the CR W8824SX drive, and is used to contr ol its basic operation. Since it resides in flash memory , it can be overwritten and updated. T o ensure the corr ect operation of the CR W8824SX drive, updates to the firmware will be made available.
Appendix Macintosh Users Use your CD writing softwar e to check the firmware version of your CR W8824SX drive. For details on how to use the software, see the documentation that came with it.
Appendix CRW8824SX Specifications Supported Formats CD-DA CD-G CD TEXT CD-ROM (*1) Mixed Mode CD-R OM (CD-ROM+CD-D A) CD-ROM XA (*1) Photo CD (*1) Video CD CD-i CD EXTRA (*2) (*3) (*4) (*4) (*4) (*4) .
Appendix Data Buffer Size 4MB (1,332 sectors) A verage Random Access Time 140 msec (reading) Sector Size 2,048 ~ 2,352 B Interface SCSI-3 (Ultra SCSI) Installing style Horizontal Disc Loading T ype T ray loading Audio Out Line Out Frequency Range: 20 ~ 20,000Hz Output Level: 1 V rms V oltage Rating 100 ~ 240V AC Current Draw 0.
Appendix A Active Desktop ................................................. 26 B BIOS ................................................................. 24 Buffer Underrun ............................................... 26 C CD TEXT ...................
.
.
If you have any questions, please contact your dealer or one of the follo wing companies. Bei weiteren F ragen wenden Sie sich Sitte an Ihren Händler oder eine der folgenden F irmen.
XY572A0.
Een belangrijk punt na aankoop van elk apparaat Yamaha CRW8824SX Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yamaha CRW8824SX Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yamaha CRW8824SX Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yamaha CRW8824SX Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yamaha CRW8824SX Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yamaha CRW8824SX Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yamaha CRW8824SX Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yamaha CRW8824SX Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
