Gebruiksaanwijzing /service van het product V150 van de fabrikant Yamaha
Ga naar pagina of 82
V150 O WNER’S MANU AL 64K-28199-13 U .S.A.Edition LIT -18626-06-99 U64K13 Hyoshi 06.2.9 16:23 ページ 1.
EMU25060 ZMU01690 Read this owner ’ s manual carefully before operating your outboard motor. U64K13 Hyoshi 06.2.9 16:23 ページ 2.
Important manual information EMU31280 To the owner Thank you for choosing a Yamaha outboard motor. This Owner’s Manual contains infor- mation needed for proper operation, mainte- nance and care. A thorough understanding of these simple instructions will help you ob- tain maximum enjoyment from your new Yamaha.
Table of contents General information .......................... 1 Identification numbers record .......... 1 Outboard motor serial number .......... 1 Key number ....................................... 1 Emission control information ........... 1 North American models.
Table of contents Shifting .......................................... 32 Forward (tiller handle and remote control models) ............................. 33 Reverse (automatic reverse lock and power trim and tilt models) ..... 33 Stopping engine ......
1 General information EMU25170 Identification numbers record EMU25183 Outboard motor serial number The outboard motor serial number is stamped on the label attached to the port side of the clamp bracket.
General information 2 EMU25262 Manufactured date label This label is attached to the clamp bracket or the swivel bracket. EMU25272 Star labels Your outboard motor is labeled with a Cali- fornia Air Resources Board (CARB) star la- bel. See below for a description of your particular label.
General information 3 EMU25300 Three Stars — Ultra Low Emission The three-star label identifies engines that meet the Air Resources Board ’ s 2008 ex- haust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low-Emission engines.
General information 4 the switch, stopping the engine. ● Know the marine laws and regulations where you will be boating — and obey them. For basic boating rules, see “ Rules of the road ” on page 5. ● Stay informed about the weather. Check weather forecasts before boating.
General information 5 EMU25401 Label W ARNING EWM01260 ● Be sure shift control is in neutral before starting engine. (except 2HP) ● Do not touch or remove electrical parts when starting or during operation. ● Keep hands, hair, and clothes away from flywheel and other rotating parts while engine is running.
General information 6 In other words, follow the standard rules ex- cept when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become “ Give-Way ” ves- sels.
General information 7 maintain your speed and direction so that the other vessel can steer itself around you. EMU25530 Other special situations There are three other rules you should be aware of when driving your boat around oth- er vessels.
General information 8 EMU25540 Fueling instructions W ARNING EWM00010 GASOLINE AND ITS VAPORS ARE HIGH- LY FLAMMABLE AND EXPLOSIVE! ● Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. ● Stop engine before refueling.
General information 9 dry rags. ● Do not overfill the fuel tank. ● Tighten the filler cap securely after re- fueling. ● If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention.
General information 10 EMU25711 Battery specifications EMU25742 Propeller selection The performance of your outboard motor will be critically affected by your choice of propel- ler, as an incorrect choice could adversely affect performance and could also seriously damage the motor.
11 Basic components EMU25797 Main components NO TE: * May not be exactly as shown; also may not be included as standard equipment on all mod- els. V150 EMU26180 Remote control The remote control lever actuates both the shifter and the throttle. The electrical switch- es are mounted on the remote control box.
Basic components 12 EMU26190 Remote control lever Moving the lever forward from the neutral po- sition engages forward gear. Pulling the le- ver back from neutral engages reverse. The engine will continue to run at idle until the le- ver is moved about 35 ° (a detent can be felt).
Basic components 13 EMU26221 Choke switch To activate the choke system, press in the main switch while the key is turned to the “” (on) or “” (start) position. The choke system will then supply the rich fuel mixture required to start the engine.
Basic components 14 gled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation. Loss of en- gine power means the loss of most steering control. Also, without engine power, the boat could slow rapidly. This could cause people and objects in the boat to be thrown forward.
Basic components 15 EMU26151 Power trim and tilt switch on bottom engine cowling The power trim and tilt switch is located on the side of the bottom engine cowling. Press- ing the switch “” (up) trims the outboard motor up, then tilts it up. Pressing the switch “” (down) tilts the outboard motor down and trims it down.
Basic components 16 EMU26340 Tilt support lever for power trim and tilt or hydro tilt model To keep the outboard motor in the tilted up position, lock the tilt support lever to the clamp bracket. EMU26382 Top cowling lock lever (pull up type) To remove the engine top cowling, pull up the lock lever(s) and lift off the cowling.
Basic components 17 EMU26470 Tachometer This gauge shows the engine speed and has the following functions. EMU26491 Digital tachometer The tachometer shows the engine speed and has the following functions. NO TE: All segments of the display will light momen- tarily after the main switch is turned on and will return to normal thereafter.
Basic components 18 EMU26550 Oil level indicator (digital type) This indicator shows the engine oil level. If the oil level falls below the lower limit, the warning indicator will start to blink. For fur- ther information, see page 22. CAUTION: ECM00030 Do not operate the engine without oil.
Basic components 19 turning on the main switch to make sure all segments come on. NO TE: The speedometer displays km/h, mph, or knots, according to operator preference. Se- lect the desired unit of measurement by set- ting the selector switch on the back of the gauge.
Basic components 20 ● Changing the display format ● Pressing the “” (mode) button chang- es the display format in the following pat- tern: ● Total hours → Trip hours → Display off ● Re.
Basic components 21 tor switch. NO TE: The fuel level reading can be affected by the position of the sensor in the fuel tank and the attitude of the boat in the water.
Basic components 22 ● The buzzer will sound (if equipped on the tiller handle, remote control box, or main switch panel). If the warning system has activated, stop the engine and check the cooling water inlet for clogging. EMU26846 Oil level warning and oil filter clogging warning Oil injection models This engine has an oil level warning system.
Basic components 23 ● The buzzer will sound (if equipped on the tiller handle, remote control box, or main switch panel). If the warning system has been activated, stop the engine and check for the cause. NO TE: The warning for oil filter clogging is similar to the warnings for low oil level and overheat- ing.
24 Operation EMU26901 Installation CAUTION: ECM00110 Incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat, or accessories such as transom ladders or depth finder transducers) can create airborne water spray while the boat is cruising.
Operation 25 motor greatly affects the water resistance. If the mounting height is too high, cavitation tends to occur, thus reducing the propulsion; and if the propeller tips cut the air, the engine speed will rise abnormally and cause the en- gine to overheat.
Operation 26 throttle to 3000 r/min or less. 3. Next two hours: Accelerate at full throttle onto plane, then reduce engine speed to three-quar- ter throttle (approximately 4000 r/min).
Operation 27 pipes. After any air in the oil lines has been expelled, the oil injection system should supply oil normally. If no oil is flowing after 10 minutes of idling, consult your Yamaha dealer. CAUTION: ECM00130 Be sure to take the above steps when op- erating the engine after a long period of storage.
Operation 28 1. Pour engine oil into the remote oil tank. NO TE: The oil level lines on the remote oil tank indi- cate the amount of additional oil that can be added to the tank. The top oil level line indi- cates approximately 1.9 L (0.5 US gal, 0.4 Imp gal) can be added, and the bottom oil level line indicates approximately 3.
Operation 29 EMU27321 Oil level indicator operation The various functions of the oil level system are as follows: EMU27381 Oil level indicator Electric start models Oil level warning indicator (digital tachometer) Oil level warning indicator (analog tachometer) Engine oil tank Remote oil tank Remarks Green more than 300 cm 3 (0.
Operation 30 EMU27450 Operating engine EMU27482 Feeding fuel W ARNING EWM00420 ● Before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you.
Operation 31 your arm or leg while operating. ● Do not attach the lanyard to clothing that could tear loose. Do not route the lanyard where it could become entan- gled, preventing it from functioning. ● Avoid accidentally pulling the lanyard during normal operation.
Operation 32 6. Turn the main switch to “” (start), and hold it for a maximum of 5 seconds. 7. Immediately after the engine starts, re- lease the main switch and allow it to re- turn to “” (on). CAUTION: ECM00191 ● Never turn the main switch to “” (start) while the engine is running.
Operation 33 EMU27764 Forward (tiller handle and remote control models) Tiller handle models 1. Place the throttle grip in the fully closed position. 2.
Operation 34 engine stop switch, then turning the main switch to “” (off). EMU27861 Trimming outboard motor The trim angle of the outboard motor helps determine the position of the bow of the boat in the water. Correct trim angle will help im- prove performance and fuel economy while reducing strain on the engine.
Operation 35 switch while the boat is moving. Adjust the outboard motor trim angle using the power trim and tilt switch. To raise the bow (trim-out), press the switch “” (up).
Operation 36 also makes the boat unstable. Resistance at the bow is greatly increased, heightening the danger of “ bow steering ” and making opera- tion difficult and dangerous. NO TE: Depending on the type of boat, the outboard motor trim angle may have little effect on the trim of the boat when operating.
Operation 37 4. Push the tilt support knob into the clamp bracket or pull the tilt support lever to- ward you to support the engine. W ARNING EWM00260 After tilting the outboard motor, be sure to support it with the tilt support knob or tilt support lever.
Operation 38 3. Push the power trim and tilt switch / pow- er tilt switch “” (down) to lower the out- board motor to the desired position. EMU28060 Cruising in shallow water The outboard motor can be tilted up partially to allow operation in shallow water.
Operation 39 3. To return the outboard motor to the nor- mal running position, press the power trim and tilt switch / power tilt switch and slowly tilt the outboard motor down.
40 Maintenance EMU31480 Specifications NO TE: “ (AL) ” stated in the specification data below represents the numerical value for the alumi- num propeller installed. Likewise, “ (SUS) ” represents the value for stainless steel propeller installed and “ (PL) ” for plastic propeller installed.
Maintenance 41 Gear oil quantity: 980.0 cm 3 (33.13 US oz) (34.56 Imp.oz) Tightening torque for engine: Spark plug: 25.0 Nm (18.4 ft-lb) (2.55 kgf-m) Propeller nut: 55.0 Nm (40.6 ft-lb) (5.61 kgf-m) EMU28222 Transporting and storing outboard motor W ARNING EWM00690 ● Leaking fuel is a fire hazard.
Maintenance 42 EMU28302 Procedure EMU28380 Flushing with the flushing attachment 1. Wash the outboard motor body using fresh water. For further information, see page 44. 2. Fill the fuel tank with fresh fuel and add one ounce of “ Yamaha Fuel Conditioner and Stabilizer ” (Part No.
Maintenance 43 NO TE: A flushing attachment is available from your Yamaha dealer. EMU28410 Lubrication (oil injection models) 1. Grease the spark plug threads and in- stall the spark plug(s) and torque to proper specification. For information on spark plug installation, see page 48.
Maintenance 44 for the most thorough flushing. CAUTION: ECM01530 Do not perform this procedure while the engine is running. The water pump may be damaged and severe damage from overheating can result. 1. After shutting off the engine, unscrew the garden hose connector from the fit- ting on the bottom cowling.
Maintenance 45 page 41. EMU28460 Checking painted surface of motor Check the motor for scratches, nicks, or flak- ing paint. Areas with damaged paint are more likely to corrode. If necessary, clean and paint the areas. A touch-up paint is avail- able from your Yamaha dealer.
Maintenance 46 EMU28522 Maintenance chart Frequency of maintenance operations may be adjusted according to the operating condi- tions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action.
Maintenance 47 W ater pump Inspection / replace- ment Oil pump Inspection / adjustment Oil tank water drain Inspection / cleaning Spark plug(s) Cleaning / adjustment / replacement Item Actions Initial.
Maintenance 48 EMU28931 Greasing Yamaha marine grease (Water resistant grease) V150 EMU28952 Cleaning and adjusting spark plug W ARNING EWM00560 When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire.
Maintenance 49 ple, if the center electrode porcelain is very white, this could indicate an intake air leak or carburetion problem in that cylinder. Do not attempt to diagnose any problems yourself. Instead, take the outboard motor to a Yamaha dealer.
Maintenance 50 Checkpoints ● Fuel system parts leakage ● Fuel line joint leakage ● Fuel line cracks or other damage ● Fuel connector leakage EMU28980 Inspecting fuel filter W ARNING EWM00310 Gasoline is highly flammable, and its va- pors are flammable and explosive.
Maintenance 51 4. Reinstall the filter element in the cup. Make sure the O-ring is in position in the cup. Firmly screw the cup onto the filter housing. 5. Attach the filter assembly to the bracket so that the fuel hoses are attached to the filter assembly.
Maintenance 52 cover, cylinder head, and body cylinder. EMU29130 Water leakage Start the engine and check that no water leaks from the joints between the exhaust cover, cylinder head, and body cylinder.
Maintenance 53 8. Tilt the outboard motor down. Check that the tilt rod and trim rods operate smoothly. NO TE: Consult your Yamaha dealer if any operation is abnormal. EMU29171 Checking propeller W ARNING EWM00321 You could be seriously injured if the en- gine accidentally starts when you are near the propeller.
Maintenance 54 EMU30660 Removing the propeller EMU29194 Spline models 1. Straighten the cotter pin and pull it out using a pair of pliers. 2. Remove the propeller nut, washer, and spacer (if equipped).
Maintenance 55 oil drain screw is at the lowest point pos- sible. 2. Place a suitable container under the gear case. 3. Remove the gear oil drain screw and gasket. NO TE: ● If a magnetic gear oil drain screw is equipped, remove all metal particles from the screw before installing it.
Maintenance 56 Yamaha dealer for inspection and replace- ment of internal anodes attached to the pow- er unit. EMU29320 Checking battery (for electric start models) W ARNING EWM00330 Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poisonous and highly caustic.
Maintenance 57 2. Always keep the battery in a good state of charge. Installing a voltmeter will help you monitor your battery. If you will not use the boat for a month or more, re- move the battery from the boat and store it in a cool, dark place. Completely re- charge the battery before using it.
Maintenance 58 wire equivalent to the starting battery cable. W ARNING EWM00600 Use of smaller wire could lead to a fire. NO TE: Consult your Yamaha dealer about correct wiring if a battery selector switch is desired. EMU29370 Disconnecting the battery Disconnect the BLACK cable from the NEG- ATIVE (-) terminal first.
59 Trouble Recovery EMU29424 Troubleshooting A problem in the fuel, compression, or igni- tion systems can cause poor starting, loss of power, or other problems. This section de- scribes basic checks and possible remedies, and covers all Yamaha outboard motors.
Trouble Recovery 60 Q. Is fuel system obstructed? A. Check for pinched or kinked fuel line or other obstructions in fuel system. Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel. Q. Is fuel filter clogged? A. Clean or replace filter.
Trouble Recovery 61 A. Have serviced by a Yamaha dealer. Q. Is load on boat improperly distributed? A. Distribute load to place boat on an even plane. Q. Is water pump or thermostat faulty? A. Have serviced by a Yamaha dealer. Q. Is there excess water in fuel filter cup? A.
Trouble Recovery 62 Q. Is fuel joint connection incorrect? A. Connect correctly. Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with rec- ommended type. Q. Is high pressure fuel pump drive belt bro- ken? A. Have serviced by a Yamaha dealer.
Trouble Recovery 63 NO TE: Consult your Yamaha dealer if the new fuse immediately blows again. EMU29522 Power trim and tilt / power tilt will not operate If the engine cannot be tilted up or down with.
Trouble Recovery 64 engine. Use the emergency starter rope only as instructed. Do not touch the fly- wheel or other moving parts when the engine is running.
Trouble Recovery 65 and start the engine. Repeat if neces- sary. EMU29670 Engine fails to operate EMU29691 Ignition system malfunction If the battery voltage is low or in the unlikely event of an ignition system malfunction, the engine speed may become erratic or the en- gine may stop.
Trouble Recovery 66 unless the oil level warning indicators are working. 1. Remove the top cowling. 2. Turn on the main switch. 3. Lift the emergency switch to pump re- serve oil into the engine oil tank from the remote oil tank. 4. After using the emergency switch, turn off the main switch, then turn it back on.
Trouble Recovery 67 2. Remove the spark plugs and face the spark plug holes downward to allow any water, mud, or contaminants to drain. 3. Drain the fuel from the carburetor, fuel filter, and fuel line. 4. Feed fogging oil or engine oil through the carburetor(s) and spark plug holes while cranking with the manual starter or emergency starter rope.
68 Consumer information EMU29811 Important warranty information for U.S.A. and Canada.
Consumer information 69.
Consumer information 70 EMU29820 YAMAHA MOTOR CORPORATION, U.S.A. OUTBOARD MOTOR TWO YEAR LIMITED WARRANTY.
Consumer information 71.
Consumer information 72.
Consumer information 73 EMU29841 IMPORTANT WARRANTY INFORMATION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA.
U64K13 Hyoshi 06.2.9 16:23 ページ 3.
Printed in Japan May 2006–0.4 × 1 ! Printed on recycled paper U64K13 Hyoshi 06.2.9 16:23 ページ 4.
YAMAHA MOTOR CO., LTD. MADE IN JAPAN PAYS D'ORIGINE JAPON OUTBOARD MOTOR W ARRANTY REGISTRA TION ENREGISTREMENT DE LA GARANTIE DU MO TEUR HORS-BORD Please complete and mail this card. This information is necessary to accurately register your unit for warranty .
PLACE POST AGE HERE A T TN: W ARRANT Y DEP ARTMENT Warranty card-04 2/17/03 2:41 PM Page 2.
Een belangrijk punt na aankoop van elk apparaat Yamaha V150 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yamaha V150 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yamaha V150 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yamaha V150 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yamaha V150 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yamaha V150 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yamaha V150 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yamaha V150 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
