Gebruiksaanwijzing /service van het product VZ200Z van de fabrikant Yamaha
Ga naar pagina of 117
VZ1 50Z/VZ1 75Z/VZ200Z er LIT -18626-04-41 VZ1 50Z VZ1 75Z VZ200Z OWNER’S MANUAL U.S.A.Edition 68J-9-12 hyoshi 01.3.27 2:19 PM y[W 1 (2,1).
USE STRAIGHT GASOLINE ONLY CAUTION • Do not use fuel mixed with oil both during break-in • Oil can damage fuel injectors. and during normal use. 000118 68J-9-12 hyoshi 01.
EMU01446 VZ150Z/VZ175Z/VZ200Z OWNER'S MANUAL ©2000 by Yamaha Motor Corporation, USA 1st Edition, November 2000 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, USA is expressly prohibited.
68J-9-12-1 3/27/01 1:33 PM Page 2.
E GENERAL INFORMA TION BASIC COMPONENTS OPERA TION MAINTENANCE TROUBLE RECOVERY INDEX READ THIS OWNER’S MANUAL CAREFULL Y BEFORE OPERA TING YOUR OUTBOARD MOTOR.
68J-9-12-1 3/27/01 1:33 PM Page 4.
EMU00004 Chapter 1 GENERAL INFORMA TION IDENTIFICATION NUMBERS RECORD .. 1-1 Outboard motor serial number...........1-1 Key number...........................................1-1 EMISSION CONTROL INFORMATION ...1-2 SAFETY INFORMATION ...................
E EMU00005 IDENTIFICA TION NUMBERS RECORD EMU00007 OUTBOARD MOTOR SERIAL NUMBER The outboard motor serial number is stamped on the label attached to the port side of the clamp-bracket.
E 1-2 000517 w q EMU01385 EMISSION CONTROL INFORMA TION EMU01444 NORTH AMERICAN MODELS This engine conforms to U.S. Environmental Protection Agency (EPA) regulations for marine SI engines. See the label affixed to your engine for details. Approval label of Emission control certifi- cate This label is attached to the bottom cowl- ing.
E 1-3 EMU01389 STAR LABELS Your outboard motor is labeled with a California Air Resources Board (CARB) star label. See below for a description of your particular label. 1 Star label One Star - Low Emission The one-star label identifies engines that meet the Air Resources Board’s 2001 exhaust emission standards.
E 1-4 EMU00917 SAFETY INFORMA TION 8 Before mounting or operating the out- board motor, read this entire manual. Reading it should give you an under- standing of the motor and its operation. 8 Before operating the boat, read any owner’s or operator’s manuals supplied with it and all labels.
E 1-5 8 When a swimmer is in the water near you shift into neutral and shut off the engine. 8 Be informed about boating safety. Additional publications and information can be obtained from many organiza- tions, including the following: United States Coast Guard Consumer Affairs Staff (G-BC) Office of Boating, Public, and Consumer Affairs U.
E 1-6 202036 w q e t 905011 r EMU00014 IMPORT ANT LABELS WARNING LABELS 2 3 WARNING 6K1-83623-41 YAMAHA Use only a counterclockwise rota tion prop eller wi th this engine. Counterclockwi se propel lers are marked with a let ter "L" after th e size indication.
E 1-7 Stand-on vessel The vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to determine how best to avoid you.
E 1-8 RULES WHEN ENCOUNTERING VESSELS There are three main situations which you may encounter with other vessels which could lead to a collision unless the Steering Rules are followed: Meeting (you ar.
E 1-9 the power-driven vessel, the power- driven vessel has the right-of-way. 2. Sailing vessels should keep clear of any fishing vessel. 3. In a narrow channel, a sailing vessel should not hamper the safe passage of a power-driven vessel which can navigate only in such a channel.
E 1-10 1 1 1 A 1 1 1 Proceeding toward head of navigation from seaward CAN BUOY Odd number. Leave to port. OR SECONDARY CHANNEL BUOYS STARTS NEW NUMBERING SYSTEM old new C " 1 " NUN BUOY Even number.
E 1-11 EMU01550 FUELING INSTRUCTIONS w GASOLINE AND ITS VAPORS ARE HIGH- LY FLAMMABLE AND EXPLOSIVE! 8 Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. 8 Stop engine before refueling. 8 Refuel in a well-ventilated area.
E 1-12 EMU00027 Gasohol There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets minimum octane ratings.
E 1-13 EMU01551 BA TTERY REQUIREMENT c C Do not use a battery that does not meet the specified capacity. If a battery which differs from the specification is used, the electrical system may perform poorly or be overloaded, causing electrical system damage.
E 1-14 602022 14-1/2x17-M 1 2 3 Yamaha outboard motors are fitted with propellers chosen to perform well over a range of applications, but there may be uses where a propeller with a different pitch would be more appropriate.
E 1-15 EMU01209 ST AR T -IN-GEAR PROTECTION Yamaha outboard motors or Yamaha approved remote control units are equipped with start-in-gear protection device(s). This feature permits the engine to be started only when it is Neutral. Always select Neutral before starting the engine.
EMU00037 Chapter 2 BASIC COMPONENTS MAIN COMPONENTS ..............................2-1 OPERATIONS OF CONTROLS AND OTHER FUNCTIONS ................................2-2 Remote control .....................................2-2 Trim tab .....................
2-1 E EMU01206 MAIN COMPONENTS !4 !2 TRIP TIME BATT Km/h knot mph km mile SPEED YAMAHA set mode !3 !1 1 2 3 4 5 x100 r/min TACH 802043 000510 q w e r o !0 i y t u 000511 w 1 Top cowling 2 Top cowling .
2-2 E EMU00039 OPERA TIONS OF CONTROLS AND OTHER FUNCTIONS EMU00096 REMOTE CONTROL Both the shifter and the throttle are actu- ated by the remote control lever.
2-3 E EMU00101 Main switch The main switch controls the ignition sys- tem; its operation is described below. 8 OFF Electrical circuits switched off. (The key can be removed.) 8 ON Electrical circuits switched on. (The key cannot be removed.) 8 START Starter-motor will turn and start engine.
2-4 E ON START OFF 701026* q w EMU00934 Engine Stop Lanyard Switch The lock-plate 1 must be attached to the engine stop lanyard switch for the engine to run. The lanyard 2 should be attached to a secure place on the operator’s cloth- ing, or arm or leg.
2-5 E 701035 EMU01155 Throttle Friction Adjusting Screw A friction device in the remote control box provides adjustable resistance to move- ment of the remote control lever, and can be set according to operator preference. An adjusting screw is located on the front of the remote control box.
2-6 E EMU01552 TRIM TAB The trim tab should be adjusted so that the steering control can be turned to either the right or left by applying the same amount of force. w An improperly adjusted trim tab may cause difficult steering. Always test run after the trim tab has been installed or replaced to be sure steering is correct.
2-7 E 302022 UP DN EMU01563 POWER TRIM/TILT SWITCH The power trim/tilt adjusts the motor angle in relation to the transom. The power trim/tilt switch is located on the side of the bottom engine cowling. Pushing the switch “UP” trims the motor up, then tilts the motor up.
2-8 E 1 2 3 4 5 x100 r/min TACH 1 2 3 4 5 x100 r/min TACH 802012 1 2 3 4 5 x100 r/min TACH 1 2 3 4 5 x100 r/min TACH 802042 EMU00135 DIGITAL TACHOMETER This meter contains the tachometer, trim meter, oil level indicator and overheat warning indicator.
2-9 E 802016* TRIP TIME BATT Km/h knot mph km mile SPEED YAMAHA set mode q w e r 1 2 3 4 5 x100 r/min TACH 1 2 3 4 5 x100 r/min TACH q 802014 1 2 3 4 5 x100 r/min TACH 1 2 3 4 5 x100 r/min TACH q 802013 EMU00138 Oil-Level Indicator This indicator shows the engine oil level.
2-10 E q w e 802023* EMU00141 Speedometer This meter shows the boat speed. NOTE: The speedometer displays km/h, mph, or knots, depending upon operator prefer- ence. Select the desired unit of measure- ment by setting the selector switch on the back of the meter.
2-11 E 802025* TRIP TIME BATT Km/h knot mph km mile SPEED YAMAHA set mode EMU01554 Fuel meter The fuel level is indicated by eight seg- ments. When all segments are showing, the fuel tank is full. c C The Yamaha fuel tank sensor differs from conventional sensors.
2-12 E EMU01555 Warning indicators 8 Fuel warning If the fuel level decreases to one segment the fuel level warning segment 1 will begin blinking. 8 Low battery voltage warning If battery voltage drops, the display 2 will automatically turn on and begin blinking.
2-13 E EMU01180 TOP COWLING LOCK LEVERS To remove the engine top cowling, pull up the front and rear lock levers. Then lift off the cowling. When replacing the cowl- ing, check to be sure it fits properly in the rubber seal. Then lock the cowling again by moving the levers downward.
2-14 E 701054 801***a 1 2 3 4 5 x100 r/min TACH EMU00169 W ARNING SYSTEM c C Do not continue to operate the engine if the warning device has activated. Consult your Yamaha dealer if the problem can- not be located and corrected. 605015 EMU01476 OVERHEAT WARNING This engine has an overheat warning device.
2-15 E 801**** 5 1 2 3 4 x100 r/min TACH 213032 q 905012 q EMU00172 OIL LEVEL WARNING / OIL FILTER CLOGGING WARNING This engine has an oil level warning sys- tem. If oil level falls below lower limit, the warning device will activate. ( 1 ); Included (—); N/A If the warning system has been activated, stop the engine and check for the cause.
2-16 E 701054 207062* q EMU01210 FUEL FILTER WATER LEVEL WARNING This engine has a fuel filter water level warning system. If water in the fuel filter cup exceeds a specific volume, the warn- ing device will activate. If the warning sys- tem has been activated, stop the engine and inspect the fuel filter.
E – MEMO – 68J-9-12-2 3/26/01 4:15 PM Page 18.
EMU00174 Chapter 3 OPERA TION INSTALLATION ........................................3-1 Mounting the outboard motor ............3-2 BREAKING IN (RUNNING IN) ENGINE ..3-4 PRE-OPERATION CHECKS ......................3-5 Operation after a long period of storage .
EMU00175 INST ALLA TION c C Incorrect engine height or obstructions to smooth water flow (such as the design or condition of the boat or accessories such as transom ladders/depth finder trans- ducers) can create airborne water spray while the boat is cruising.
EMU01478 MOUNTING THE OUTBOARD MOTOR w 8 Overpowering a boat may cause severe instability. Do not install an outboard motor with more horsepower than the maximum rating on the capacity plate of the boat. If the boat does not have a capacity plate, consult the boat manu- facturer.
Mount the outboard motor on the center line (keel line) of the boat, and ensure that the boat itself is well balanced. Otherwise, the boat will be hard to steer.
3-4 E EMU01494 BREAKING IN (RUNNING IN) ENGINE Your new engine requires a period of break-in (running-in) to allow mating sur- faces of moving parts to wear-in evenly. Correct break-in (running-in) will help ensure proper performance and longer engine life.
3-5 E 2) Next 50 minutes: Do not exceed half throttle (approxi- mately 3,000 r/min). Vary engine speed occasionally. If you have an easy-planing boat, accelerate at full throttle onto plane, then immediately reduce the throttle to 3,000 r/min or less.
3-6 E EMU00206 Fuel 8 Check to be sure you have plenty of fuel for your trip. 8 Make sure there are no fuel leaks or gasoline fumes. 8 Check fuel line connections to be sure they are tight. 8 Be sure the fuel tank is positioned on a secure, flat surface, and that the fuel hose is not twisted or flattened, or likely to contact sharp objects.
3-7 E EMU01184 OPERATION AFTER A LONG PERIOD OF STORAGE (for Yamaha oil injection system model) When operating the engine after a long period (12 months) of storage, proceed as follows: 1) Start the engine. Leave it idling. w 8 Do not touch or remove electrical parts when starting or during operation.
3-8 E EMU00186 FILLING FUEL AND ENGINE OIL EMU01031 FILLING FUEL 1) Remove the fuel tank cap. 2) Fill the fuel tank carefully. 3) Close the cap securely after refueling. Wipe up any spilled fuel. EMU01019 Ring Free Fuel Additive Gasoline is a precise blend of many differ- ent substances, each chosen to give cer- tain characteristics.
3-9 E EMU01185 FILLING OIL (for Yamaha oil injection system model) This engine uses the Yamaha oil injection system, which provides superior lubrica- tion by ensuring the proper oil ratio for all operating conditions. No fuel pre-mixing is needed. Simply pour gasoline into the fuel tank and oil into the oil tank.
Yellow 1,500 cm 3 (1.6 US qt, 1.31 Imp qt) or less EMU01543¯ Oil Level Indicator The various oil level system functions are as follows: Remarks Oil level indicator (Digital tachometer) Oil level indicator (Analog tachometer) Engine oil tank Remote oil tank Green Red Green Red More than 300 cm 3 (0.
3-11 E 902025 EMU01197 ST AR TING ENGINE w 8 Before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you. 8 When the air vent screw is loosened, gasoline (petrol) vapor will be released.
3-12 E EMU00248 PROCEDURE FOR REMOTE CONTROL MODEL 4) Place the remote control lever in the Neutral position. NOTE: The start-in-gear protection device per- mits the engine to be started only when it is in Neutral. 5) Attach the engine stop switch lanyard to a secure place on your clothing, or your arm or leg.
3-13 E 309034 EMU01198 W ARMING UP ENGINE 1) Before beginning operation, allow the engine to warm up at idling speed for 3 minutes. (Failure to do this will shorten engine life.
701043 N F N R 701044 EMU00261 SHIFTING w Before shifting, make sure there are no swimmers or obstacles in the water near you. c C To change the shifting position from for- ward to reverse or vice-versa, close the throttle first so that the engine idles (or runs at low speeds).
3-15 E ON START OFF 701023 EMU00273 STOPPING ENGINE Let it cool off for a few minutes at idle or low speed first. Stopping the engine immediately after operating at high speed is not recommended.
3-16 E 000521 q EMU01412 TRIMMING OUTBOARD MOTOR The trim angle of the outboard motor helps determine the position of the bow of the boat in the water. The correct trim angle will help improve performance and fuel economy while reducing strain on the engine.
3-17 E UP DN 702014 q EMU01401 Power Trim/Tilt Model w 8 Be sure all people are clear of the out- board motor when adjusting the trim/tilt angle, also be careful not to pinch any body parts between the drive unit and clamp bracket. 8 Use caution when trying a trim position for the first time.
3-18 E EMU01558 Bow Up When the boat is on plane, a bow-up atti- tude results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees. When trimmed out, the boat may have more tendency to steer to one side or the other.
3-19 E 000516 EMU01200 TIL TING UP/DOWN If the engine will be stopped for some time, or if the boat is moored in shallows, the engine should be tilted up to protect the propeller and casing from damage by collision with obstructions, and also to reduce salt corrosion.
3-20 E UP DN UP DN 702014 403035* EMU01548 PROCEDURE FOR TILTING UP Power trim/tilt models 1) If there is a fuel joint or a fuel cock on the boat, disconnect the fuel line or close the fuel cock. 2) Push the power trim/tilt switch “UP” until the outboard has tilted up com- pletely.
3-21 E EMU00316 CRUISING IN OTHER CONDITIONS CRUISING IN SALT WATER After operating in salt water, wash out the cooling-water passages with fresh water to prevent them from becoming clogged- up with salt deposits. NOTE: Refer to cooling system flushing instruc- tions in “TRANSPORTING AND STORING OUTBOARD MOTOR”.
EMU00317 Chapter 4 MAINTENANCE SPECIFICATION DATA .............................4-1 TRANSPORTING AND STORING OUTBOARD MOTOR ...............................4-3 Trailering outboard motor ...................4-3 Storing outboard motor .....................
Recommended fuel P.O.N. Fuel tank capacity l (US gal, Imp gal) Recommended engine oil Fuel/oil premix ratio Fuel : Oil Engine oil capacity (engine oil tank) l (US qt, Imp qt) (remote oil tank) l (US q.
4-2 E 25 (2.5, 18) 55 (5.5, 40) VZ175TRZ VZ200TRZ — 792 (31.2) 554 (21.8) 1,693 (66.6) 516 (20.3) 217 (478) 4,500 - 5,500 128.7 (175) @ 5,000 670 - 730 2-stroke, 76°V6 2,596 (158.
4-3 E EMU01369 TRANSPORTING AND STORING OUTBOARD MOTOR w Leaking fuel is a fire hazard. When trans- porting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking. 000515 102074 EMU00326 TRAILERING OUTBOARD MOTOR The motor should be trailered and stored in the normal running position.
4-4 E EMU01187 STORING OUTBOARD MOTOR When storing your Yamaha outboard for prolonged periods of time, (2 months or longer), several important procedures must be performed to prevent expensive damage.
4-5 E 903021 EMU00338 Flushing Cooling System and Fogging Engine Cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. In addition, fog- ging of the engine is mandatory to pre- vent expensive engine damage due to rust.
4-6 E EMU01568 Lubrication 1) Remove the spark plug(s). Spray “Yamaha Stor-Rite Engine Fogging Oil” into each cylinder for 5 seconds. Grease the spark plug threads and reinstall the spark plug(s) and torque to proper specification. (Refer to the section “CLEANING AND ADJUST- ING SPARK PLUG” for details).
4-7 E EMU01545 Battery Care w Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. It con- tains sulfuric acid. Avoid contact with skin, eyes, or clothing. Antidote: EXTERNAL: Flush with water. INTERNAL: Drink large quantities of water or milk.
4-8 E 901015 UPPER LEVEL LOWER LEVEL 2) Clean the battery casing and termi- nals. Fill each cell to the upper level with distilled water. 3) Store the battery on a level surface in a cool, dry, well-ventilated place out of direct sunlight.
4-9 E EMU00362* MAINTENANCE CHART Frequency of maintenance operations may be adjusted according to the operating con- ditions, but the following table gives general guidelines. The mark ( 6 ) indicates the check-ups which you may carry out yourself. The mark ( 1 ) indicates work to be carried out by your Yamaha dealer.
4-10 E EMU00366 GREASING Yamaha marine grease (Water resistant grease) 000523 68J-9-12-4 3/26/01 4:16 PM Page 11.
4-11 E EMU01202 CLEANING AND ADJUSTING SPARK PLUG w When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire. The spark plug is an important engine component and is easy to inspect.
4-12 E When fitting the plug, always clean the gasket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque. NOTE: If a torque-wrench is not available when you are fitting a spark plug, a good esti- mate of the correct torque is 1/4 to 1/2 a turn past finger-tight.
4-13 E 106092 EMU01509 CHECKING FUEL SYSTEM w Gasoline (petrol) and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames or other sources of ignition. Check the fuel line for leaks, cracks, or malfunctions. If any problem is found, it should be repaired immediately by Yamaha dealer or other qualified mechan- ic.
4-14 E 207063 w e t y r EMU00370 INSPECTING FUEL FILTER w Gasoline (petrol) is highly flammable, and its vapors are flammable and explosive. 8 If you have any question about properly doing this procedure, consult your Yamaha dealer. 8 Do not perform this procedure on a hot or running engine.
4-15 E 4) Reinstall the filter element. Make sure the O-ring is in position in the cup. Insert the cup and O-ring into the fil- ter housing 6 . Screw the ring nut onto the filter housing until the ring is lightly seated. 5) Tighten the ring nut approximately an additional 1/4 turn until ring nut is tight.
4-16 E A diagnostic tachometer should be used for this procedure. 1) Start the engine and allow it to warm up fully in Neutral until it is running smoothly.
4-17 E 206016 EMU01189 CHECKING HIGH PRESSURE FUEL PUMP DRIVE BELT Inspect the high pressure fuel pump drive belt and replace it if any of the following signs is observed: 8 Cracks in the back of the belt or in the base of belt teeth. 8 Excessive wear at the roots of cogs.
4-18 E 000500 r t w e r e q EMU01330 REPLACING FUSE If a fuse has blown, remove the electrical cover, open the fuse holder and remove the fuse with a fuse puller. Replace it with a spare one of proper amperage. w Be sure to use the specified fuse. An incorrect fuse or a piece of wire may allow excessive current flow.
4-19 E EMU00993 CHECKING POWER TRIM AND TILT SYSTEM w 8 Never get under the lower unit while it is tilted, even when the tilt-support lever is locked. Severe injury could occur if the outboard accidentally falls. 8 Make sure no one is under the out- board before performing this test.
4-20 E 210012 602051 602036 602074 w e r q y t EMU00388 CHECKING PROPELLER w You could be seriously injured if the engine accidentally starts while you are near the propeller. 8 Before inspecting, removing or installing the propeller, remove the spark plug caps from the spark plugs.
4-21 E EMU01560 Installing the Propeller c C 8 Be sure to install the thrust washer before installing propeller, otherwise the lower case and propeller boss may be damaged. 8 Be sure to use a new cotter pin and bend the ends over securely. Otherwise, the propeller could come off during operation and be lost.
4-22 E 000565 w q EMU01460 CHANGING GEAR OIL w 8 Be sure the outboard is securely fas- tened to the transom or a stable stand. You could be severely injured if the out- board falls on you. 8 Never get under the lower unit while it is tilted, even when the tilt-support lever/knob is locked.
4-23 E 5) With the outboard motor in a vertical position, and using a flexible or pres- surized filling device, inject the gear oil into the oil drain plug hole. 6) When the oil begins to flow out of the oil level plug hole, insert and tighten the oil level plug.
4-24 E EMU00404 CHECKING BATTERY (for Electric start models) w Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poi- sonous and highly caustic. Always follow these preventive mea- sures: 8 Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury.
4-25 E c C 8 A poorly maintained battery will quick- ly deteriorate. 8 Ordinary tap-water contains minerals harmful to a battery, and should not be used for topping-up. 1) Check the electrolyte level at least once a month. Fill to the manufactur- er’s recommended level when neces- sary.
4-26 E c C 8 Make sure the main switch (on applica- ble models) is “OFF” before working on the battery. 8 Reversal of the battery leads will dam- age the rectifier. 8 Connect the RED lead first when installing the battery and disconnect the RED lead last when removing it.
4-27 E EMU00408 CHECKING BOLTS AND NUTS 1) Check that bolts securing the cylinder head and engine and the nut securing the flywheel are tightened with their specified tightening torque. 2) Check the tightening torque of other bolts and nuts. EMU01280 Disconnecting the Battery Disconnect the BLACK lead from the NEG- ATIVE (-) terminal first.
4-28 E 000524 q w e EMU01172 CLEANING COOLING-WATER PASSAGES Flushing device equipped model Perform this procedure right after opera- tion for the most thorough flushing. 1) After shutting off the engine, unscrew the garden-hose connector 2 from the fitting 1 on the bottom cowling.
4-29 E 102025 EMU00413 COATING THE BOAT BOTTOM A clean hull improves boat performance. The boat bottom should be kept as clean of marine growths as possible. If neces- sary, the boat bottom can be coated with an anti-fouling paint approved for your area to inhibit marine growth.
EMU00414 Chapter 5 TROUBLE RECOVER Y TROUBLESHOOTING ..............................5-1 TEMPORARY ACTION IN EMERGENCY ............................................5-5 Impact damage .....................................5-5 Power trim/tilt will not operate .
5-1 E EMU01204 TROUBLESHOOTING A problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. The troubleshooting chart describes basic checks and possi- ble remedies. (This chart covers all Yamaha outboard motors.
5-2 E C. Engine idles irregularly or stalls. Trouble Possible Cause Remedy 1. Spark plug(s) fouled or incorrect type. 2. Fuel system obstructed. 3. Fuel contaminated or stale. 4. Fuel filter clogged. 5. Failed ignition parts. 6. Warning system activated.
5-3 E D. Warning buzzer sounds or indicator lamp lights. Trouble Possible Cause Remedy 1. Cooling system clogged. 2. Engine oil level low. 3. Heat range of spark plug incorrect. 4. Specified engine oil not used. 5. Engine oil contaminated or deteriorated.
5-4 E Trouble Possible Cause Remedy 13. Poor connections or damaged ignition wiring. 14. Failed ignition parts. 15. Specified engine oil not used. 16. Thermostat faulty or clogged. 17. Air vent screw closed. 18. Fuel pump damaged. 19. Fuel joint connection incorrect.
5-5 E EMU00416 TEMPORARY ACTION IN EMERGENCY EMU01492 IMPACT DAMAGE w The outboard motor can be seriously damaged by a collision while operating or trailering. Damage could make the out- board motor unsafe to operate. If the outboard motor hits any object in the water, follow the procedure below.
5-6 E EMU01561 STARTER WILL NOT OPERATE If the starter mechanism does not operate (engine cannot be cranked with the starter), the engine can be manually start- ed with an emergency starter rope. However, the engine can not be manually started if the battery voltage is low.
5-7 E ON START OFF 701026 703043 ON ON 301052 208083 208084 EMU01309 Emergency Starting Engine 1) Remove the top cowling. 2) Remove the flywheel cover. 3) Prepare the engine for starting. See “STARTING ENGINE” for procedures. Be sure the engine is in Neutral and that the lanyard is attached to the engine stop switch.
5-8 E EMU01565 LOW OIL LEVEL WARNING ACTIVATES If the oil level is allowed to drop too low, the red segment will appear on the oil level indicator, the buzzer will sound, and engine speed will be limited to about 2,000 r/min.
5-9 E NOTE: 8 Reserve oil capacity is maximum 1,500 cm 3 (1.6 US qt, 1.31 Imp qt). 8 The oil feed pump will not operate if the engine is tilted more than 35°.
5-10 E EMU01511 TREATMENT OF SUBMERGED MOTOR If the outboard motor is submerged, immediately take it a Yamaha dealer. Otherwise, some corrosion may begin almost immediately. If you cannot immediately take the out- board motor to a Yamaha dealer, follow the procedure below in order to minimize engine damage.
E – MEMO – 68J-9-12-5 3/26/01 4:17 PM Page 12.
EMU00450 Chapter 6 INDEX INDEX ........................................................6-1 1 2 3 4 5 6 E 68J-9-12-6 3/27/01 4:09 PM Page 1.
6-1 E EMU00451 INDEX A Adjusting idling speed .......................... 4-15 Adjusting trim angle ..............................3-17 B Basic boating rules ..................................1-7 Battery care.............................................
6-2 E Mounting the outboard motor ...............3-2 N Neutral interlock trigger ..........................2-3 Neutral throttle lever ...............................2-3 O Oil level indicator ............................2-9, 3-10 Oil level warning/ oil filter clogging warning .
EMU01051 IMPORT ANT W ARRANTY INFORMA TION FOR U.S.A. AND CANADA Welcome to the Yamaha Family! Congratulations on the purchase of your new Yamaha marine power. Yamaha is commit- ted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying one.
5. Your warranty applies specifically to repairs made in the country of purchase. If your U.S.-purchased Yamaha needs warranty service while in Canada, or your Canadian pur- chased Yamaha needs service while in the United States, Yamaha will assist the local dealer whenever possible.
EMU00912* Y AMAHA MOTOR CORPORA TION, U.S.A. OUTBOARD MOTOR TWO YEAR LIMITED W ARRANTY Yamaha Motor Corporation, U.S.A. is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to customer satisfaction.
SPECIFIC PARTS EXCLUDED FROM WARRANTY. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, shear pins, propellers, hubs, fuel and oil filters, brushes for the starter motor and power tilt motor, water pump impellers, and anodes are not covered by warranty.
CUSTOMER SERVICE If your machine requires warranty service, you must take it to any authorized Yamaha outboard dealer within the continental Uni ted States. Be sure to bring your warranty registration identification or other valid proof of the original date of purchase.
EMU01178 IMPORT ANT W ARRANTY INFORMA TION IF YOU USE YOUR Y AMAHA OUTSIDE U.S.A. OR CANADA Welcome to the Yamaha Family! Congratulations on the purchase of your new Yamaha marine power. Yamaha is com- mitted to exceptional customer satisfaction, and we want your ownership experience to be a satisfying one.
68J-9-12-6 3/27/01 4:09 PM Page 10.
GM6-9-05-6 0.10.13 16:59 ページ 6-7.
VZ1 50Z/VZ1 75Z/VZ200Z Printed in Japan November 2000—0.5 × 1 ! 68J-28199-12 (Z150QETO/Z175HETO/Z200PETO) Printed on recycled paper OW 68J-9-12 hyoshi 01.
VZ1 50Z/VZ1 75Z/VZ200Z er LIT -18626-04-41 VZ1 50Z VZ1 75Z VZ200Z OWNER’S MANUAL U.S.A.Edition 68J-9-12 hyoshi 01.3.27 2:19 PM y[W 1 (2,1).
Een belangrijk punt na aankoop van elk apparaat Yamaha VZ200Z (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yamaha VZ200Z heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yamaha VZ200Z vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yamaha VZ200Z leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yamaha VZ200Z krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yamaha VZ200Z bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yamaha VZ200Z kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yamaha VZ200Z . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
