Gebruiksaanwijzing /service van het product YST-SW1500 van de fabrikant Yamaha
Ga naar pagina of 24
I YS T -SW 1 500 Subwoofer System O WNER’S MANU AL U B 1-YST-SW1500(UB)PRE-f 02.9.2, 6:45 PM 1.
II • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to aler t you to the presence of uninsulated “dangerous voltage” within the product’ s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
III W e W ant Y ou Listening For A Lifetime Y AMAHA and the Electronic Industries Association ’ s Consumer Electronics Group want y ou to get the most out of your equipment b y playing it at a safe le vel.
IV CHECKING THE ACCESSORIES Check your package to make sure it contains the following items. For U .K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted.
English E- 1 Please read the follo wing operating precautions before use. Y AMAHA will not be held responsible f or any damage and/or injur y caused b y not follo wing the cautions below . ● T o assure the finest perf ormance, please read this manual carefully .
E- 2 CONTENTS IMPORT ANT SAFETY INSTRUCTIONS ................................................................. II CHECKING THE A CCESSORIES .......... IV CA UTION .................................................. 1 FEA TURES .........................
E- 3 PLA CEMENT One subwoofer will have a good effect on your audio system, however , the use of two subwoofers is recommended to obtain more effect. If using one subwoofer , it is recommended to place it on the outside of either the right or the left main speaker .
E- 4 OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT SPLIT SUBWOOFER SUBWOOFER ( LOW PASS ) AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
English E- 5 AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
E- 6 AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
English E- 7 䡵 Using two subw oofers Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer , and connect the OUTPUT terminals of the subwoofer to the main speak ers.
E- 8 MAIN IN PRE OUT AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.P.F.OUTPUT OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
English E- 9 MAIN IN PRE OUT AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
E- 10 Gr ound connection AC IN ON POWER OFF HIGH LOW OFF AUTO STANDBY OUTPUT INPUT REMOTE OUTPUT TO SPEAKERS INPUT 1 FROM AMPLIFIER 100Hz 80Hz /MONO NORMAL INPUT 2 INPUT 3 LFE GND H.
English E- 11 Battery replacement If you find that the remote control must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones. Notes ● Use only AA, R6, UM-3 batteries for replacement. ● Be sure the polarities are correct.
E- 12 1 ST ANDBY/ON button Press this button to turn on the power . Press again to set the subwoof er in the standby mode. * This button can be used only when the PO WER ( A ) s witch is set in the ON position. Standby mode The subwoof er is still using a small amount of pow er in this mode.
English E- 13 4 V OLUME control V OLUME UP/DOWN b uttons Adjust the volume le vel. T urn the control clockwise or press the UP button to increase the v olume. T urn the control counterclockwise or press the DO WN button to decrease the v olume. T o adjust the control on the front panel, put a coin, etc.
E- 14 If the source being pla yed is stopped and the input signal is cut off f or 7 to 8 minutes, the subw oof er automatically s witches to the standby mode . (When the subwoofer s witches to the standby mode b y the automatic pow er- s witching function, the power indicator lights up in red.
English E- 15 1 Set the v olume le v el on the amplifier to minimum, and turn on the amplifier and other components. 2 T ur n the V OLUME control to set the control to minimum (0). 3 Make sure that the PO WER switch on the rear panel is set to the ON position, then press the ST ANDBY/ON button to turn on the subwoof er .
E- 16 Storing preset data of the V OLUME control etc. Y ou can store preset data of the V OLUME control, the HIGH CUT control, the PHASE b utton and the B.A.S.S. s witch as a set. Each of the three PRESET buttons on the remote control is used to store (and recall) one set of data.
English E- 17 This subwoofer’ s frequency characteristics EX.1 When combined with a 4” or 5” (10 cm or 13 cm) acoustic suspension, 2 way system main speakers EX.2 When combined with an 8” or 10” (20 cm or 25 cm) acoustic suspension, 2 way system main speakers PHASE –Set to the reverse mode.
E- 18 AD V ANCED Y AMAHA A CTIVE SER V O TECHNOLOGY The theory of Y amaha Active Servo T echnology has been based upon two major f actors, the Helmholtz resonator and negative-impedance driv e. Active Ser vo Processing speakers reproduce the bass frequencies through an “ air woof er ” , which is a port or opening in the speaker ’ s cabinet.
English E- 19 What to Do Connect the power cab le to both the AC IN sock et of the subwoof er and an AC outlet securely , or set the POWER s witch to the ON position. Raise the volume up . Connect them securely . Connect them correctly , that is L (left) to L, R (right) to R, “ + ” to “ + ” and “–” to “–” .
E- 20 SPECIFICA TIONS T ype ............... Advanced Y amaha Active Servo T echnology Driver ............................................ 30 cm (12”) cone woofer Magnetic shielding type Amplifier Output ..............................................
Een belangrijk punt na aankoop van elk apparaat Yamaha YST-SW1500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Yamaha YST-SW1500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Yamaha YST-SW1500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Yamaha YST-SW1500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Yamaha YST-SW1500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Yamaha YST-SW1500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Yamaha YST-SW1500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Yamaha YST-SW1500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
