NL
Ferm logo
Officiële handleiding

Ferm MSM1037

92 pagina's·7.4 MB·Zaagmachine·PDF·ENJA
Ferm MSM1037
Inhoudsopgave 19 secties MSM1037 · DE · NL · FR · … TonenVerbergen
Page 1 of the Ferm MSM1037 user manual — www.ferm.com
Pagina 1 · klik om te vergroten
Pagina 1
Ferm MSM1037 — MSM1037 diagram (page 1)
Afb. 1
Ferm MSM1037 — MSM1037 diagram (page 1)
Afb. 2

MSM1037

DE

Übersetzung der Originalbetriebsanleitung 12

NL

Vertaling van de oorspronkelijke gebruiksaanwijzing 20

Traduction de la notice originale 28

FR

ES

Traducción del manual original 36

IT

Traduzione delle istruzioni originali 44

SV

Översättning av bruksanvisning i original 52

FI

Alkuperäisten ohjeiden käännös 59

HU

Eredeti használati utasítás fordítása 68

Překlad püvodního návodu k používání 74

CS

MK

Оригинални упатства 81

www.ferm.com

Original instructions 05

Page 2 of the Ferm MSM1037 user manual — MSM1037
Pagina 2 · klik om te vergroten
Pagina 2
Ferm MSM1037 — MSM1037 diagram (page 2)
Afb. 3
Ferm MSM1037 — MSM1037 diagram (page 2)
Afb. 4
Page 3 of the Ferm MSM1037 user manual — MSM1037
Pagina 3 · klik om te vergroten
Pagina 3
Ferm MSM1037 — MSM1037 diagram (page 3)
Afb. 5
Ferm MSM1037 — MSM1037 diagram (page 3)
Afb. 6
Page 4 of the Ferm MSM1037 user manual — MSM1037
Pagina 4 · klik om te vergroten
Pagina 4
Ferm MSM1037 — MSM1037 diagram (page 4)
Afb. 7
Page 5 of the Ferm MSM1037 user manual — 1. Machine information
Pagina 5 · klik om te vergroten
Pagina 5

MITRE SAW

Angle for bevelling 45º (only left)

Mitre saw maximum sawing capacity:

Thank you for buying this Ferm product. By doing so you now have an excellent product, delivered by one of Europe’s leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

Mitre 0º, Bevel 0º 55x120mm

Mitre 45º, Bevel 45º 32x80mm

Mitre 45º, Bevel 0º 55x80mm

Mitre 0º, Bevel 45º 32x120mm

Weight 6.6 kg

Lpa (sound pressure) 91 dB(A), KpA: 3dB

Lwa (acoustic capacity) 104 dB(A), KwA: 3dB

Vibration level

The numbers in the following text refer to the pictures on page 2 - 4

Vibration level The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 61029-1; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned.

Read the operating instructions carefully before using this device. Familiarise yourself with its functions and basic operation. Service the device as per the instructions to ensure that it always func tions properly. The operating instructions and the accompanying documentation must be kept in the vicinity of the device.

- using the tool for different applications, or with

Intended use The electric tool is intended as a stationary machine for making straight lengthways and crossways cuts in wood. Horizontal mitre angles of -45° to +45° as well as vertical bevel angles of -45° are possible.

different or poorly maintainted accessories, may significantly increase the exposure level. - the times when the tool is switched off or when

it is running but not actually doing the job, may significantly reduce the exposure level.

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Contents 1. Machine information 2. Safety 3. Mounting accessories 4. Operation 5. Service & Maintenance

Package contents 1 TCT Saw blade: 210 x 30mm (T48) 1 Workpiece clamp 1 Dust bag 1 Carbon brush set 1 Rear support 2 Side extensions 1 Hex key 1 Pair of safety glasses 1 Set earplugs

1. Machine information

Mains voltage 230-240V,~ 50Hz

Machine class II (double insulated)

Check the machine, loose parts and accessories for transport damage.

No load speed 4500/min

Saw blade measurement 210x30x2.5mm

Angle for mitring 45º (left and right)

Technical specifications · Capacity 1300 W

Page 6 of the Ferm MSM1037 user manual — MITRE SAW
Pagina 6 · klik om te vergroten
Pagina 6

Features Figs. 1, 2, 3, 4 and 5 1. On/off switch 2. On/off switch for laser 3. Unlock button (Blade protective cover) 4. Cover carbon brush 5. Lock-pin 6. Blade protective cover 7. Workpiece clamp 8. Guide fence 9. Knob adjusting saw angle 10. Locking knob 11. Laser battery 12. Sliding fence knob 13. Connection dust bag 14. Bevel angle 15. Handle 16. Cover 17. Saw blade bolt 18. Flange 19. Screw 20. Retraction arm 21. Extension pieces (left and right) 22. Lock-button saw blade 23. Angle indicator 24. Support bracket

Symbols The following symbols are important for the operations of your power tool. The correct interpretations of the symbols helps you operate the power tool more save.

Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instruction in this manual.

Caution, risk of electric shock.

Ferm MSM1037 — MITRE SAW diagram (page 6)
Afb. 8

Keep bystanders away.

Wear eye protection.

Wear ear protectors. Exposure to noise can cause hearing loss.

Wear a dust mask.

Danger Area! Keep hands far away (10cm) from the cutting area while the machine is running. Danger of injury when coming in conatct with the saw blade.

By using electric tools basic safety precautions should always be followed to reduce the risk of fire. Electrical shock and personal injury. Always read the specific product instruction manual and the safety instructions before attempting to operate the power tool and store these instructions.

Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself, not even from a distance. This power tool produced laser class 2 laser radiation according to EN 60825-1. This lead can lead to person being blinded.

Install of a stationary machine Fig. 6 This machine is a stationary machine and for safety reasons must always be firmly installed and not used for mobile applications. You can install the machine in two ways: a) As a stationary machine on a workbench.

Disc dimensions. Observe the dimensions of the saw blade. The hole diameter must match the tool spindle without play. *Use only a fill ring which is specified by supplier, filling ring may not have any play.

In case the machine must be secured to the workbench with 4 bolts. b) As a stationary machine on a sub frame. In this

case the machine must be secured to the sub frame with 4 bolts and the sub frame anchored with 4 bolts to the floor plate with dimensions of at least 1 square meter.

Tranport the machine only when the machine is in inward transport position.

Page 7 of the Ferm MSM1037 user manual — MITRE SAW
Pagina 7 · klik om te vergroten
Pagina 7
1. Work area safety a) Keep work area clean and well lit. Cluttered or
3. Power tool safety The first time that the machine is used and then every subsequent time that it is used:

dark areas invite accidents. b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders far away while

Before carrying out any work on the machine, disconnect the mains plug from the power supply.

operation a power tool. Distractions can cause you to lose control, or material can shut away. d) Never leave the machine unattended without

General: Check the entire saw machine. If any part of the machine is missing, bent, damaged or is dysfunctional in any other way, or if any mechanical and/or electrical faults occur or are visible, or if the machine makes any extremely loud noises, refer to the user manual. If any defects are detected on the machine, they must all be rectified before the machine is used. Only original parts should be used! If you have any outstanding concerns which could affect your own safety or the safety of the machine, please consult the machine supplier.

first disconnecting it from the mains voltage.

2. Personal safety a) If you are not familiar with using such machine.

You would be better to be informed first by a professional, an instructor or by a technician. b) Store idle power tools out of the reach of

children. Power tools are dangerous in the hands of untrained users. c) Keep power tools dry, clean and free from oil

and grease. Properly maintained power tools are safer and easier to control. Grease oil handles are slippery causing loss of control. d) Make sure you always have a clean and tidy

Electrical a) Always use an Original power plug which

matches the outlet, do not use an adapter plug with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electrical shock. b) Do not use the machine with a damaged

working environment. You could slip or trip. e) Stay alert, watch what you are doing and use

common sense when operating a power tool. f) Do not overreach. Keep proper footing and

balanced at all the time. This enables better control of the power tool in unexpected situations. g) Do not work with a machine while you under

power cable. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Damaged cables increase the risk of an electrical shock. c) Check the cable regularly and have a damaged

the influence of alcohol, drugs or medication. Inattention while operating power tools may result in very dangerous injury. h) Use always protective equipment. Always wear

cable repaired. Replacing cables or plugs. Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet. Use original power cord and plugs, repairing only through an authorized person, this will ensure that the safety of the power tool is maintained! d) To prevent electrical shocks. When plugging

eye protection, dust mask, hearing protectors and safety shoes. By service on machine or raw materials use gloves. Keep your hair back. Reduce changes on personal injury. i) Be careful when sawing double miter joints.

Saw blade, Work piece and your hands must be always visible during sawing. j) Never saw more than one piece of work at the

the plug into the socket the metal pins must not be touched in any way whatsoever. e) Do not expose power tools to rain or wet

same time. k) Make sure that the piece of work not have any

conditions. Water entering a power tool will increase the risk of electrical shock. f) Never use the cord to pull the plug out of the

nails/ staples or other foreign objects in it. l) Never process metal or stone with this machine. m) Do not work with material containing asbestos.

socket. Keep the cord and plug away from oil, heat and sharp objects.

Page 8 of the Ferm MSM1037 user manual — MITRE SAW
Pagina 8 · klik om te vergroten
Pagina 8

g) When operating a power tool outdoors, use an

Exchange damaged saw blades immediately, always use original flenses, nut and/ or bolts. j) Remove any adjusting key or wrench before

extension cord suitable for outdoor use. Use a cord for outdoor use reduces the risk of electric shock. h) When machine is equipped with laser. Do not

turning the power tool. A wrench or a key left attached to a rotating part of the power tool may result in a personal injury and very dangerous situation. k) The arrow marked on the saw blade, which

direct the laser beam at persons or animals and do not stare into the laser beam yourself. Not even in distance. Laser must be according to EN 60825-1 Class 2. i) Repairs of a laser may only be carried out by

indicates the direction of rotation. Must point in the same direction as the arrow marked on the machine, the saw blade teeth must point downwards on the front of the saw. l) Do not touch the saw blade after work before it

the laser manufacture or a specialist. j) If operating a power tool in a damp location

is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

has cooled. The saw blade becomes very hot while working. m) Protect the saw blade from strikes and shocks.

Mechanical a) Before you start the machine, check if the saw

Do not apply side pressure to the saw blade. n) Do not force the power tool. Use the correct

blade is allowed to rotate freely. Check in every different position of the saw machine if the saw blade revolves freely, if the saw blade touches anything the machine must be adjusted or repaired. b) Do not use the power tool if the switch does

power tool for your application. The correct power tool will do the job better and safer at the rate which it was signed. o) Never stand on the power tool. Serious injury

can occur when the power tool tips over. Always use extra support for more stability of the machine. p) Machine is provided with devices for the

not turn on and off. A power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Always use saw blades with the correct size

connection of dust extraction, ensure these are connected and properly used. Dust collection reduce dust- related hazard’s. q) Maintain the air outlets at the machine. Dust

and shape. Use saw blades recommended by the manufacture (EN-847-1). Saw blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control. Only buy saw blades with a suitable number of revolutions of at least 4500 RPM. d) Never use too small or too big saw blades.

must be removed. r) Make sure that the guard operates properly

and that it can move freely. Never lock the guard in place when opened. s) Never remove cutting remainders from the

This is very dangerous. e) Never remove marking on saw blade. Technical

sawing area while the machine is running. Always guide the tool arm back to the neutral position first and then switch the machine off. t) Guide the saw blade against the work piece

information must always visible to make the right choices by exchanging the saw blade. f) Secure the work piece. Always clamp work

only when the machine is switched on. Otherwise there is a risk of a kickback, when the saw blade becomes wedged in the work piece. u) If the saw blade should become jammed.

piece with clamping devices, this is much safer than by hand. g) Never leave the machine before the complete

stopped. h) Do not use High speed steel saw blades (HSS).

Switch the machine off and hold the work piece until the saw blade comes to a complete stop. v) To prevent a kick back. The work piece may not

Saw blade can easily break. i) Do never use dull, cracked, bent or damaged

be moved until after the machine has complete stopped. Correct the cause for the jamming of the saw blade before restarting the machine. w) When sawing profile sections, round pieces or

saw blades. Before use pull the mains plug and check the saw blade. Damaged or unsharpened saw blades produce narrow kerf, excessive friction, blade binding and kickback.

other pieces, always press the piece of work

Page 9 of the Ferm MSM1037 user manual — 3. Assembly and accessories
Pagina 9 · klik om te vergroten
Pagina 9

against the stop and can’t move, so it cannot till or turn or move while sawing. x) Never use the machine to saw pieces of work

end and fix well to provide safety support for work piece. • For bevel cuts, adjust the sliding fence (8)(12) to a suitable position as close as to the saw blade surface but avoid interfere the saw blade movement and ensure to fix well.

that are to small that they cannot be secured safely. Small pieces of wood or other objects that come in contact with the rotating saw blade can strike the operator or out standers with high speed. y) When sawing always use the additional

Changing the saw blades Fig. 4 and 5

supports. z) For sawing of large piece work that not

Only use saw blades that are sharp and undamaged. You must immediately replace chipped or bent saw blades.

supported. Use extra supports. aa) Never make warning signs on the machine

unrecognizable. Technical information or machine type information must be always visible on machine. At the end of the sawing process, keep the saw head downstairs, switch off the machine and wait until the all moving parts has come to a stop before you take your hands off the machine.

  • Do not use this saw to cut metal or masonry
  • Disconnect the machine from the power supply.
  • Remove the screw (19) that holds the retraction arm(20).
  • Press the saw blade lock button (22) and hold. Rotate the saw blade carefully by hand until the blade locks.
  • Use hex key to remove the saw blade bolt (17) by loosening in a clockwise direction.
  • Lift the blade cover (6) upwards using unlock button (3) and hold it.
  • Remove the Flange (18) and the saw blade.
  • Replace the saw blade making sure that the arrow marked on the saw blade must point in the same direction as the arrow shown marked on the machine. The saw blade teeth must point downwards.
  • Lower the blade cover (6).
  • Replace Flange and fix the saw blade bolt (17) use the saw blade lock button (22) to secure tightly.
  • Attach the retraction arm (20) back by tightening the screw (19).
  • Rotate the saw blade manually and check if the guard operates freely.

3. Assembly and accessories

  • Installation of the mitre saw
  • Place one sidebar (21) on the right-hand side of the machine and the other sidebar on the left-hand side of the machine.
  • Place the work piece clamp (7) on the left or right side of the machine.
  • Hold the handgrip and move the saw slightly downwards and then pull the pin (5) out slightly so that saw moves upwards.
  • Mounting the anti-tip over support.
  • The anti-tip over support (24) is pre mounted.
  • Always extend the anti-tip over support when using the machine.

Sliding fence Fig. 2 For safety reasons, this machine is equipped with a moveable guide fence to used in normal and bevel cutting. • For normal straight cross-cuts and mitre cuts, always adjust the sliding fence (8)(12) to the

Page 10 of the Ferm MSM1037 user manual — 5. Service and maintenance
Pagina 10 · klik om te vergroten
Pagina 10

Adjusting the cutting angle Fig. 2 Adjusting Mitre Angles The mitre angle can be set between 45° left side and 45° right side - Loosen the locking knob (10). - Turn the saw table left or right until the angle

4. Operation

Using the mitre saw Fig. 1

Before use, always check for faults or defects!

indicator (23) indicates the required angle. - Tighten the locking knob (10).

  • Set the desired sawing angle of the machine.
  • Put the plug into the socket.
  • Fix the piece of work in place using the clamp (7): make sure that the material is well clamped in place!
  • Hold the material tightly on the left side while making sure that you keep a safe distance from the blade of the saw.
  • Turn on the machine using the switch (1).
  • Make sure that the saw blade has reached full speed before allowing it to touch the piece of work to be sawn.
  • Use knob (3) to raise the protective cover lock.
  • Now bring the saw slowly downwards so that the saw blade saws through the piece of work and passes through the slot in the table. Do not put any pressure on the saw. Give the machine time to saw through the piece of work.
  • Bring the machine gently up again and switch it off by letting go of the switch (1).

Pre-settings (quick settings) on the following degrees: -45°, -40°, -35°, -30°, -25°, -20°, -15°, -10°, -5°, 0°, 5°, 10°, 15°, 20°, 25°, 30°, 35°, 40°, 45°.

Adjusting Bevel Angles Fig. 1 and 3 The bevel angle can be set between 0° and 45°.

Adjust sliding fence accordingly! See chapter 3, sliding fence.

- Loosen the adjusting knob (9). - Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle. - Tighten the adjusting knob (9).

Changing the carbon brushes Fig. 2 - Disconnect the machine from the power

supply. - Unscrew the two covers (4) on the front and

  • Using the laser Fig. 2
  • To switch on the laser , press the on/off switch 2.
  • To switch off the laser , release the on/off switch 2.

backside of the motor housing. - Replace the carbon brushes with the exact

type of brushes. - Tighten the covers (4) again. Note: Always replace both carbon brushes at the same time, never use a mixture of old and new brushes.

5. Service and maintenance

Mounting the dust bag Fig. 1 Press in the clamp of the dust bag (13) and slide it onto the opening on the back of the machine. The dust bag stays in place when you release the clamp.

Always make sure that the machine is not connected to the mains electricity when you carry out any maintenance of the mechanism.

Cleaning Clean the machine housing regularly with a soft cloth, preferably after each time you use the machine. Make sure that the ventilation slots are free of dust and dirt. For stubborn dirt use a soft

Page 11 of the Ferm MSM1037 user manual — ENVIRONMENT
Pagina 11 · klik om te vergroten
Pagina 11

cloth dampened with soapy water. Never use solvents such as benzene, alcohol, ammonia, etc. These types of solvents can damage the plastic parts.

WARRANTY

The warranty conditions can be found on the separately enclosed warranty card.

  • Problem solving 1. The motor does not start
  • The plug is not in the socket.
  • The power cord is broken.
  • The switch is defective. Take the machine to your dealer for repair.

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

  • 2. The saw cut is not even (jagged)
  • The saw blade must be sharpened.
  • The saw blade is mounted back to front.
  • The saw blade is clogged with resin or sawdust.
  • The saw blade is not suitable for the piece of work being used.

Only for EC countries Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

3. The height and/or mitre lever is obstructed • Chips and/or dust must be removed.

The product and the user manual are subject to change. Specifications can be changed without further notice.

  • 4. The motor has difficulty in reaching full speed
  • The extension cord is too thin and/or too long.
  • The mains voltage is less than 230 V.
5. The machine vibrates excessively • The saw blade is damaged.
6. The machine becomes excessively hot • The ventilation slots are blocked. Clean them out with a dry cloth.
7. The electromotor runs unevenly • The carbon brushes are worn out. Replace the carbon brushes or consult your dealer.

Lubrication The machine does not need any extra lubrication.

Faults Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

Vraag stellen over de Ferm MSM1037

Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nog geen vragen over de Ferm MSM1037

Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.

Origineel document

Ferm MSM1037 handleiding-pdf

92 pagina's·7.4 MB·Zaagmachine·PDF
Klik op een bovenstaande pagina om deze hier te openen
Pagina 1 / …
100%
Pagina's laden…