Gebruiksaanwijzing /service van het product DSA-N2B20 van de fabrikant Bosch Power Tools
Ga naar pagina of 40
DSDA iSCSI Disk Array Series DSA-S5B50 | DSA-N2B20 | DSA-N2B50 en Installation Guide.
.
DSDA iSCSI Disk Array Series Table of Cont ents | en 1 Bosch Security Syst ems Installation Guide V 1 | 2008.08 T able of Contents 1P r e c a u t i o n s 3 2 Introduction 4 2.1 Systems at a Glance 4 3 Unpacking and Installing the Hardware 6 4 Delivery Status 7 5 Configuration through the Web Interface 8 5.
2 en | Table of Cont ents DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems.
DSDA iSCSI Disk Array Series Precautions | en 3 Bosch Security Syst ems Installation Guide V 1 | 2008.08 1 Precautions – The system is heavy even without disks in s talled.
4 en | Introduction DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 2 Introduction This guide explains the installation of the digital storage systems of type – DSA-S5B50 – DSA-N2B20 – DSA-N2B50 for either direct stor age of recorded video data or for use with the VRM Video Recording Manager application.
DSDA iSCSI Disk Array Series Introduction | en 5 Bosch Security Syst ems Installation Guide V 1 | 2008.08 Example front side (DSA-N2B20): Example rear side (DSA-N2B20): Expansion unit – disk shelf: Front side Expansion unit – disk shelf: Rear side 2.
6 en | Unpacking and Installing t he Hardware DSDA iSCSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 3 Unpacking and Installing the Hardware 1. Unpack your system by opening the packing box and lifting the outer shipping box off the pallet.
DSDA iSCSI Disk Array Series Delivery Status | en 7 Bosch Security Syst ems Installation Guide V 1 | 2008.08 4 Delivery Status For use with the VRM Video Recording Manager ap plication or for direct recording from Bosch cameras and senders, the sy stem should be configured following the steps in the next chapter.
8 en | Configuration through th e Web Int er face DSDA iS CSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 5 Configur ation through the W eb Interface Follow these steps to configure each system. Th is procedure is nearly identical for all three types of storage systems.
DSDA iSCSI Disk Array Series Configuration through the W eb Interface | en 9 Bosch Security Syst ems Installation Guide V 1 | 2008.08 2. Select from the Control Panel of your computer Network Connections , Properties . Here, configure your network interface to use IP address 10.
10 en | Configuration through th e Web Int er face DSDA iS CSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 5. Enter root as the user name, leave the password blank. The FilerView start page lo ads and shows an overview on the system status.
DSDA iSCSI Disk Array Series Configuration through the W eb Interface | en 11 Bosch Security Syst ems Installation Guide V 1 | 2008.08 8. Click Modify next to the network interface labeled e0a and configured with IP address 10.10.10.10. 9. Enter the IP address informati on for the network.
12 en | Configuration through th e Web Int er face DSDA iS CSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 19. The changes are summarized on the Commit screen . Click Commit to apply the new settings. 5.3 Configuring the V olume The system is preconfigured with one volume that contains either two or three hard disks.
DSDA iSCSI Disk Array Series Configuration through the W eb Interface | en 13 Bosch Security Syst ems Installation Guide V 1 | 2008.08 27. The changes are summarized on the Commit screen. Click Commit to apply the new settings. By default, one disk is left as a spare disk.
14 en | Configuration through th e Web Int er face DSDA iS CSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 5.4 Cre ating an Initiator Group 32. In the navigation panel, select LUNs > Initiator Groups > Add . The Add Initiator Group screen displays.
DSDA iSCSI Disk Array Series Configuration through the W eb Interface | en 15 Bosch Security Syst ems Installation Guide V 1 | 2008.08 The following procedure must be carr ied out for each LUN to be created. 39. In the navigation panel, select LUNs > Wizard .
16 en | Configuration through th e Web Int er face DSDA iS CSI Disk Array Series V 1 | 2008.08 Installation Guide Bosch Security Systems 47. On the Add Initiator Groups screen, click Next . 48. LUN ID : Leave this fiel d blank. The lowest av ailable ID will be used automatically.
DSDA iSCSI Disk Array Series Adding St orage | en 17 Bosch Security Syst ems Installation Guide V 1 | 2008.08 6 Adding St orage Storage shelves can be ad ded to the DSA-N2B20 and the DSA-N2B50 system. Each expansion unit comes with 14 disks, 750 GB each.
18 en | Adding St orage DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 2. Set the correct Shel f ID by pressing the + or – button at the back of th e shelf, next to the ID display. Note: Do not use identical IDs for different shelves.
DSDA iSCSI Disk Array Series Adding St orage | en 19 Bosch Security Syst ems Installation Guide V 1 | 2008.08 6.1.3 Connecting the Shelf 4. Connect the shelves using the supplied cables.
20 en | Adding St orage DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 9. Volume Parameters : Volume Name : Enter a name for the new volume. The name should consist of the word vol and the ID of the disk shelf you just adde d (e.
DSDA iSCSI Disk Array Series Adding St orage | en 21 Bosch Security Syst ems Installation Guide V 1 | 2008.08 24. On the following two screens, click Next and leave all options to their default value. On the third screen ( Other ), uncheck Access Time .
22 en | Adding St orage DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 6.1.5 Creating LUNs For each newly created volume, you must create at least one LUN, as pr eviously created LUNs cannot not be reconfigured to use them for the new volume.
DSDA iSCSI Disk Array Series Monitoring and Maint enance | en 23 Bosch Security Syst ems Installation Guide V 1 | 2008.08 7 Monitoring and Maint enance 7.1 Monitoring the Sy st em 7.1.1 Using the FilerView Monitor The system should be monitored. An overa ll system status monitor is provided by the FilerView administration interface.
24 en | Monitoring and Maint enance DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 7.2 Maintenance 7.2.1 Disk Replacement DSA-S5B50 Follow these steps to replace a disk: 1. Remove the new disk driv e from the antistatic bag.
DSDA iSCSI Disk Array Series Monitoring and Maint enance | en 25 Bosch Security Syst ems Installation Guide V 1 | 2008.08 3. Rotate the handle to extract the disk. 4. Support the bottom of th e drive to remove it. 5. Reverse these steps to replace the hard disk.
26 en | Monitoring and Maint enance DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 7.3 Hardware T roubleshooting 7.3.1 DSA-S5B50 LEDs on front side, left: If the Power Indicator is not lit green, the system has no powe r.
DSDA iSCSI Disk Array Series Monitoring and Maint enance | en 27 Bosch Security Syst ems Installation Guide V 1 | 2008.08 7.3.2 DSA-N2B20 / DSA-N2B50 LEDs on front side, right: If the Power LED is not lit green, the s ystem has no power. X Check the cables and switch the system on.
28 en | Monitoring and Maint enance DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems There are four LEDs on the power supply unit on the rear side of each shelf. If either the Fan LED or the Power LED are lit amber , the power supply unit must be replaced.
DSDA iSCSI Disk Array Series Monitoring and Maint enance | en 29 Bosch Security Syst ems Installation Guide V 1 | 2008.08 1. Upload the new soft ware to a Web server – If you are using VRM, place the file that contains the new version in C:Program FilesBoschVideo Recording ManagerVRM Serverweb on your VRM Server.
30 en | Monitoring and Maint enance DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 5. If a new mainboard firmware comes with th e release (check the release notes), on the console, at the prompt LOADER> , enter update_flash .
DSDA iSCSI Disk Array Series T echnical Data | en 31 Bosch Security Syst ems Installation Guide V 1 | 2008.08 8 T echnical Data For more detailed information, please refer to the data sheets with the latest information available on www.boschsecurity.com under Product Catalog > CCTV > IP Video > Disk Arrays .
32 en | T echnical Data DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 8.2 T echnical Specifications DSA-N2B20 8.2.1 Electrical Requirements – One Controller Module 8.2.2 System Hardwa re Specifications 8.2.3 Mechanical 8.
DSDA iSCSI Disk Array Series T echnical Data | en 33 Bosch Security Syst ems Installation Guide V 1 | 2008.08 8.3 T echnical Specifications DSA-N2B50 8.3.1 Electrical Requiremen ts – One Controller Module 8.3.2 System Hardware Specifications 8.3.3 Mechanical 8.
34 en | T echnical Data DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems 8.4 T echnical Specifications Disk Shelf Expansion Unit – DSX -N2X00-14A T 8.4.1 Electrical Requirements 8.4.2 System Hardwa re Specifications 8.
DSDA iSCSI Disk Array Series T rademar ks | en 35 Bosch Security Syst ems Installation Guide V 1 | 2008.08 9 T r ademarks Java is a trademark of Sun Microsystems.
36 en | T rademarks DSDA iS CSI Disk Array Serie s V 1 | 2008.08 Installation Guide Bosch Security Systems.
.
Bosch Security Systems Robert-Koch-Straße 100 D-85521 Ottobrunn Germany Telefon 089 6290-0 Fax 089 6290-1020 www.boschsecurity.com © Bosch Security Systems, 2008.
Een belangrijk punt na aankoop van elk apparaat Bosch Power Tools DSA-N2B20 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bosch Power Tools DSA-N2B20 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bosch Power Tools DSA-N2B20 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bosch Power Tools DSA-N2B20 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bosch Power Tools DSA-N2B20 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bosch Power Tools DSA-N2B20 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bosch Power Tools DSA-N2B20 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bosch Power Tools DSA-N2B20 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
