Gebruiksaanwijzing /service van het product 2210 Series van de fabrikant Brinkmann
Ga naar pagina of 32
OWNER’S MANUAL W ARNING HAZARDOUS EXPLOSION MA Y RESUL T IF THESE W ARNINGS AND INSTRUCTIONS ARE IGNORED. READ AND FOLLOW ALL W ARNINGS AND INSTRUCTIONS IN THIS MANUAL T O A VOID PERSONAL INJUR Y , INCLUDING DEA TH OR PROPERTY DAMAGE.
1 WE W ANT YOU T O ASSEMBLE AND USE YOUR GRILL AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION T O POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL.
2 General W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and LP Cylinder Specifications and Safe Use . . . . . . . . . . . . . . 4–6 Connecting LP Cylinder and Hose / Regulator to Grill .
3 W ARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal briquets or lighter fluid in a gas grill. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill.
4 W ARNING W ARNING LP GAS CYLINDER (NOT SUPPLIED WITH THIS GRILL) The LP cylinder is available for purchase at the same location the grill was purchased. The LP (Liquid Propane) gas cylinder specifically designed to be used with this grill must have a 20 lb.
5 The cylinder must also be equipped with: • A shut-off valve terminating in a T ype 1 gas cylinder valve outlet. • A T ype 1 valve that prevents gas flow until a positive seal is obtained. • An arrangement for vapor withdrawal. • A collar to protect the cylinder shut-off valve.
FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder . • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity .
7 W ARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas grill must be used.
LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame.
W ARNING 9 6. Check each place listed (A – K) for growing bubbles which indicates a leak. 7. T urn off gas supply at cylinder valve. 8. T urn on control knobs to release gas pressure in hose. 9. T urn control knobs to "OFF" position. 10. T ighten any leaking connections.
LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the "OFF" position.
LIGHTING THE SIDE BURNER: 1. Open lid before lighting side burner . 2. Make sure control knob is in the "OFF" position. 3. Push and turn side burner control knob to the "HIGH" position. 4. Press the electronic igniter on the main control panel an d hold for 3 – 5 seconds to light burner .
12 OPERA TING THE GRILL: Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill.
ROTISSERIE COOKING: • Y our grill was pre-drilled from factory to include mounting holes for a rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie.
14 GRILL COOKING TIPS CLEANLINESS • Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw meat, uncooked poultry or seafood.
BURNER ASSEMBL Y/MAINTENANCE • Although your burners are constructed of cast iron, they may rust as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage.
16 TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for Leak T esting.
17 TROUBLE SHOOTING Problem: Possible Causes: 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will match light. Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed.
18 Y our grill's serial number and model number , and the contact information for Brinkmann Customer Service, are listed on a silver label found on the back of the grill or on the grill body side, under the side shelf. These questions and answers are for your general knowledge, and may not be applicable to your model grill.
Cleaning Stainless Steel Cooking Grills: W ash grills with a mild detergent and rinse with hot water before initial use and as needed. DO NOT use a comm ercial oven cleaner . For stubborn food residue, use a degreaser and fiber or brass cleaning brush.
20 2 M8 X 15mm bolts 2 M8 X 15mm shoulder bolts 6 M6 X 12mm bolts 1 AA /1.5V Alkaline battery 2 Large Star W ashers 6 Small Star W ashers P AR TS BAG CONTENTS Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process.
ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT .
ELECTRONIC IGNITER FOR ASSISTANCE, CALL 800-527-0717 FOR OUTDOOR USE ONLY BURNER CENTER 7. To light the left and right burners, push and turn control knobs to HIGH. Follow Step 6. 8. Refer to owner’s manual for match lighting procedure. 9. To turn off, turn each control knob clockwise until it locks in OFF position.
Choose a good, cleared assembly area and get a friend to help you put your grill together . Lay cardboard down to protect grill finish and assembly area. Step 1 With the help of a friend, turn the preassembled cart over . T ry to minimize the stress to the bottom plate.
Step 4 Snap wheel hub caps onto the outside of wheels as illustrated. Step 5 With the help of a friend, turn the cart to its upright position. Step 6 Attach tank heat shield to heat shield plate using one #8 self-tapping screw .
25 Step 7 Attach heat shield plate to back panel using two M6 X 12mm bolts with small star washers. Step 8 Attach heat shield plate to front panel using three #8 self-tapping screws.
26 Note: When performing Step 10, Lift grill body from front and rear panels to avoid injury to hands and fingers. Be sure to pass hose/regulator assembly above cart frame crossbar . Step 10 With the help of a friend, place grill body assembly on preassembled cart frame.
Step 1 1 Attach side table assembly to left side of cart frame assembly . Slide side table assembly onto preattached shoulder bolts. Attach two more shoulder bolts as illustrated and secure. Step 12 Attach side burner assembly to right side of cart frame assembly .
28 Step 13 Attach the hose heat shield to the right side of the cart frame using two #8 self-tapping screws. Step 14 Remove two bolts and washers from the side burner valve. Insert the side burner valve assembly through the hole in the side burner table base, then firmly seat the valve nozzle into the burner venturi.
Cooking Grills Porcelain Heat T ents Brackets W arming Rack Step 16 Attach side burner igniter lead wire to the electrode as illustrated. Step 17 Insert grease tray into opening on backside of grill. Make sure to slide tray onto tracks as illustrated.
7. To l igh t the left a nd righ t bu r ne rs , pu s h and t urn cont r o l k no bs to HI GH. Fol low S tep 6 . 8. R e fer t o owner’ s m a nu al for match li g hti n g proc e dure.
140-2210-0 9/03, 10/04, 4/05 Owner ’s Manual for Model 810-2210-0 The Brinkmann Corporation warrants to the original purchaser that the Brinkmann ProSeries™ 2210 is free from defects due to workma.
Een belangrijk punt na aankoop van elk apparaat Brinkmann 2210 Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Brinkmann 2210 Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Brinkmann 2210 Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Brinkmann 2210 Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Brinkmann 2210 Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Brinkmann 2210 Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Brinkmann 2210 Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Brinkmann 2210 Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
