Gebruiksaanwijzing /service van het product S1526 van de fabrikant Addtron Technology
Ga naar pagina of 29
H3C S1526 Smart Ethernet Switch Installation Manual Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-IM-20080 221-3.03.
Copyright © 2005-2008, Hangzhou H3C Technologies Co., Ltd. All Rights Reserved No part of this manual may be re produced or tran smitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co.
Technical Support soho@h3c.c om http://www.h3c.com.
About This Manual Purpose This document is used to guide you throu gh installing this product. Please read it carefully before your operation. Intended Audience This document is intended for network admini strators who kno w well of the basic network kno wl edge and network terms.
Chapter Content 5 Appendix – Port Properties This chapter describes the port properties, such as the connector type and quantity. Conventions The manual uses the following conventions: Symbols I. Convention Description Caution Means reader be ca reful.
Installation Manual H3C S1526 Smart Ethernet Switch Table of Contents i Table of Contents Chapter 1 Product Ov erv iew ........................................................ 1-1 1.1 Introduction ......................................................
Installation Manual H3C S1526 Smart Ethernet Switch Table of Contents ii Chapter 4 Appendix – Technical Specifications ........................ 4-1 Chapter 5 Appendix – Port Proper tie s ......................................... 5-1 5.1 Properties of 10/100B ase -TX Ethernet Ports .
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 1 Product Overview 1-1 Chapter 1 Product Overview 1.1 Introduction H3C S1526 Smart Ethernet Switch (hereinaf ter referred to as the S1526) is suitabl e for the networking of small and medium-si zed enterprises, and Internet cafe.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 1 Product Overview 1-2 1.2 Appearance 1.2.1 Front Panel As shown in Figure 1-1 , the S1526 has on it s front panel from the left to the right: Power LED, 10/100Ba se-TX port LEDs, 10/100Base-TX ports, 100 0 Mbps uplink combo port s and LEDs, and Console port.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 1 Product Overview 1-3 LED Stat u s Description Green A link is established. OFF No link is est ablished. Link/Act Blinking Data is being transmitted or received. 1.2.2 Rear Panel The S1526 has one A C power socket on its re ar p anel, as shown in Figure 1-2 .
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-1 I. Chapter 2 Installation 2.1 Precautions T o avoid any damage to the device or human body a rising from improper use of the S1526, please follow the precautions an d requirement s listed below .
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-2 II. III. z Do not open the chassis while the switch is in ope ration. Do not open the chassis if not necessary, even when the switch is not powered on. Installation Environment Requirements The S1526 can be inst alled in a corridor or a room.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-3 z Electromagnetic shiel ding approach is adopted when necessary, such as using shielded p ort cable. z All port cables are wired indoor, to prevent the ports from any damage that may be caused by overvoltage and overcurrent from lightning strike.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-4 Figure 2-1 Fix the mounting ears 3) Put the switch in a rack tray. Slide the switch al ong the guide rails to an appro priat e place. 4) Fix the mounting ears to the ra ck posts with screws at both sides.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-5 Note: The mounting brackets are used for fixing rathe r than weight bearing. In a 19-inch standard rack, the weight of the switch is supp orted by the tray beneath it. 2.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-6 I. II. 2.3 Connecting the Cables 2.3.1 Connecting Devices to the Switch Connect the dev ice to the Ethernet port Use either crossover cables or straig ht through cables to connect th e PC(s) or othe r device (s) to the Ethernet ports on the switch.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-7 Caution: To avoid eye damages, do not look di rectly at the laser beam inside the optical fiber. 2.3.2 Connecting the Console Cable Figure 2-5 Connecting the switch to a terminal through con sole port The switch can be configured thro ugh a terminal.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-8 Caution: Because the PC serial port is not hot-swappable, DO NOT plug the cable connector into or unplug it from the PC seri al port when the switch is powered on.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-9 2.4 Starting Up the Switch 2.4.1 Configuring Terminal Parameters 1) Start the PC. In the Wi ndows operating system, click [Start/ Programs/A ccessori es/ Communications] to run the Hyper Terminal progra m o n the PC.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-10 MAIN MENU 1. Modify password 2. Set IP address/Subnet mask/Gateway 3. Reset to default configuration 4.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-11 Note: For detailed information about the configuratio n commands, refer to H3C S1526 Smart Ethernet Switch User Manual .
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 2 Installation 2-12 Note: For detailed information about the Web configuration , refer to H3C S1526 Smart Ethernet Switch User Manual.
Installation Manual H3C S1526 Smart Ethernet Switch Chapt er 3 Troubleshooting 3-1 I. Chapter 3 Troubleshooting 3.1 Password Loss If you lose your password for t he switch, restore the switch to the factory settings at first by referring to H3C S1526 Smart Ethernet Switch User Manual.
Installation Manual H3C S1526 Smart Ethernet Switch Chapt er 3 Troubleshooting 3-2 II. z The console cable is in good conditio n and the terminal (HyperTermin al for example) parameter settings are correct. Refer to section 2.4.1 “ Configuring Terminal Parameters ” for information about terminal parameter settings.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 4 Appendix – Technical Specifications 4-1 Chapter 4 Appendix – Technical Specifications Table 4-1 T echnical specifications Item Descrip.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 4 Appendix – Technical Specifications 4-2 Item Description S torage humidity (noncondensi ng) 10% to 90% System cooling Air cooling.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 5 Appendix – Port Properti es 5-1 Chapter 5 Appendix – Port Properties 5.1 Properties of 10/100Base-TX Ethernet Ports Table 5-1 Properti.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 5 Appendix – Port Properti es 5-2 5.2 Properties of 1000 Mbps Ethernet Ports Table 5-2 Properties of 1000 Mbp s Ethernet port s Item Descr.
Installation Manual H3C S1526 Smart Ethernet Switch Chapter 5 Appendix – Port Properti es 5-3 Item Description S tandard suppor ted IEEE802.3ab Media and transmission distance 50/125µm multimode op.
Een belangrijk punt na aankoop van elk apparaat Addtron Technology S1526 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Addtron Technology S1526 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Addtron Technology S1526 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Addtron Technology S1526 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Addtron Technology S1526 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Addtron Technology S1526 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Addtron Technology S1526 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Addtron Technology S1526 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
