NL
DURATECH logo
Officiële handleiding

DURATECH Controller (PL-REM)

44 pagina's·369 KB·Controller·PDF·EN
DURATECH Controller (PL-REM)
Inhoudsopgave 16 secties PL-REM Manual · LINK Driver · Table of contents · Technical specifications · … TonenVerbergen
Page 1 of the DURATECH Controller (PL-REM) user manual — LINK Driver
Pagina 1 · klik om te vergroten
Pagina 1

PL-REM Manual

English Page 2 Nederlands Pagina 12 Français Page 22 Deutsch Seite 32

DURATECH Controller (PL-REM) — PL-REM Manual diagram (page 1)
Afb. 1 · PL-REM Manual

LINK Driver

12-09-22

Page 3 of the DURATECH Controller (PL-REM) user manual — Technical specifications
Pagina 3 · klik om te vergroten
Pagina 3

Technical specifications

Nominal Input voltage Max rating Relay Contacts “Color&Light”, “A” and “B” Resistive Load

230 VAC 50 Hz

14A 250VAC 14A 30VDC 6A 250VAC 6A 30VDC 868 MHz Class II

Frequency band transmitter IEC Protection Class

Ambient air temperature Humidity

0°C ... +40°C 10% ... 90% RH non condensing 150x157x51 mm 500 g IP54

Dimensions Weight Ingress protection rate

For operation only with 12VAC safety isolation transformer to power Spectravision® LED Pool Lights

Electrical specifications · Inductive Load · General specifications Controller

Page 4 of the DURATECH Controller (PL-REM) user manual — Box contents
Pagina 4 · klik om te vergroten
Pagina 4

Box contents

1. PL-REM controller 2. Handheld transmitter (DuraLink™ version) 3. Spare battery (type A23 12V) 4. Screws (4x) & wall plugs (4x) 5. Owners’s manual
DURATECH Controller (PL-REM) — Box contents diagram (page 4)
Afb. 2 · Box contents
Page 5 of the DURATECH Controller (PL-REM) user manual — 230VAC
Pagina 5 · klik om te vergroten
Pagina 5

Installation instructions

Option 1PL-REM in transformer primary
  • Connect a 230VAC power source to the “220-240VAC INPUT” terminal
  • Connect the primary circuit of a 12VAC transformer (sold separately) in series with the “Color&Light” terminal of the PL-REM.

Optional: The “Switch A” & “switch B” terminals can be used to control auxiliary circuits like a pool cover or garden lights.

The “Color&Light” relay contact has an output of 14A, which can drive a 12V transformer of max. 3000W (220Vx14A).

DURATECH Controller (PL-REM) — Installation instructions diagram (page 5)
Afb. 3 · Installation instructions

230VAC

12VAC

230VAC 230VAC

Pool cover · Garden lights

Page 6 of the DURATECH Controller (PL-REM) user manual — 230VAC
Pagina 6 · klik om te vergroten
Pagina 6
Option 2PL-REM in transformer secondary
  • Connect a 230VAC power source to the “220-240VAC INPUT” terminal
  • Connect the secondary circuit of a 12VAC transformer (sold separately) in series with the “Color&Light” terminal of the PL-REM.

Optional: The “Switch A” & “switch B” terminals can be used to control auxiliary circuits like a pool cover or garden lights.

The “Color&Light” relay contact has an output of 14A, or 170W on a 12V transformer secondary (14Ax12V). The total load of pool lights can not exceed this.

DURATECH Controller (PL-REM) — Installation instructions diagram (page 6)
Afb. 4 · Installation instructions

230VAC

12VAC

230VAC 230VAC

Pool cover · Garden lights

Page 7 of the DURATECH Controller (PL-REM) user manual — Pairing handheld transmitter & controller
Pagina 7 · klik om te vergroten
Pagina 7

Pairing handheld transmitter & controller

The handheld transmitter is already paired in the factory and ready to use. The PL-REM can pair with up to 6 handheld transmitters. In case a problem arises, the pairing process can be done manually:

Manual Pairing process:

Make sure the PL-REM is connected to a power source. 1. Press the pairing button on the small circuit board, inside the con- troller for at least 5 seconds. --> The LED will start to blink fast

2. Within 25 seconds, press any button on the handheld transmitter. --> If the transmitter is paired correctly, the LED will flash slowly for 5 times --> If the PL-REM pairing memory is full, the LED will flash 15 times. This means 6 handheld devices have already been paired.

To unpair all handheld transmitters with the controller: Push the pair- ing button for at least 5 seconds, then do nothing for at least 25 sec- onds. --> The pair memory will be erased - the green LED will flash 5x on/off.

If no transmitters are paired, the PL-REM-200 will accept messages from any transmitter!

Pairing button · Green LED

Page 8 of the DURATECH Controller (PL-REM) user manual — Replacing transmitter battery
Pagina 8 · klik om te vergroten
Pagina 8

Handheld transmitter functions

Toggle the lamps ON/OFF

Go to next color scenario

Toggle Output A ON/OFF

Toggle Output B ON/OFF

Replacing transmitter battery

  • Remove the philips head screw and open the transmitter
  • Replace the battery, respecting the polarity
Battery typeA23 12V
DURATECH Controller (PL-REM) — Replacing transmitter battery diagram (page 8)
Afb. 5 · Replacing transmitter battery
DURATECH Controller (PL-REM) — Replacing transmitter battery diagram (page 8)
Afb. 6 · Replacing transmitter battery

+

Page 9 of the DURATECH Controller (PL-REM) user manual — Change Relay A/B mode
Pagina 9 · klik om te vergroten
Pagina 9

Change Relay A/B mode

The relays A & B can be used to control auxiliary circuits like garden lighting or a pool cover. The operation mode of these relays can be modified: Option 1: Normal open/closed contact Option 2: Pulsed contact

Modification process: 1. Locate the 5 pinholes on the circuit board 2. Make a connection between pin 1 and 2 (use a piece of wire, or a paperclip) 3. Power ON the device by connecting a 230VAC power source to the 220-240VAC INPUT terminal 4. Power OFF the device 5. Remove the connection between pin 1 and 2

Every time the above process is repeated, the A & B relays switch between Normal open/closed mode and Pulsed operation mode

DURATECH Controller (PL-REM) — Change Relay A/B mode diagram (page 9)
Afb. 7 · Change Relay A/B mode

Pin 1 Pin 2

DURATECH Controller (PL-REM) — Change Relay A/B mode diagram (page 9)
Afb. 8 · Change Relay A/B mode
Page 10 of the DURATECH Controller (PL-REM) user manual — Troubleshooting
Pagina 10 · klik om te vergroten
Pagina 10

Troubleshooting

PROBLEM SOLUTION

The controller doesn’t react to transmitter commands

  • Check the battery of the handheld transmitter
  • The transmitter is not pairedcorrectly with the controller. Repeat the pairing process
  • Reduce the distance between handheld transmitter and PLREM and/or remove obstacles
  • The pool lights don’t work
  • Check if all connections are made according to the electrical scheme on page 5 or 6.
  • Check if the “Color&Light” output terminals of the controller switch on and of when pushing the on/off button on the transmitter.
Page 11 of the DURATECH Controller (PL-REM) user manual — Troubleshooting
Pagina 11 · klik om te vergroten
Pagina 11
Page 11 of the DURATECH Controller (PL-REM) user manual — Troubleshooting
Page 12 of the DURATECH Controller (PL-REM) user manual — Inhoudstafel
Pagina 12 · klik om te vergroten
Pagina 12

Inhoudstafel

Technische specificaties Inhoud van de doos Installatie instructies Afstandsbediening en controller koppelen Afstandsbediening functies Batterij van de afstandsbediening vervangen Relais A/B modus veranderen Probleemoplossing

Pagina 13 Pagina 14 Pagina 15-16 Pagina 17 Pagina 18 Pagina 18 Pagina 19 Pagina 20

Vraag stellen over de DURATECH Controller (PL-REM)

Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nog geen vragen over de DURATECH Controller (PL-REM)

Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.

Origineel document

DURATECH Controller (PL-REM) handleiding-pdf

44 pagina's·369 KB·Controller·PDF
Klik op een bovenstaande pagina om deze hier te openen
Pagina 1 / …
100%
Pagina's laden…