Gebruiksaanwijzing /service van het product CDS-2 van de fabrikant Bunn
Ga naar pagina of 34
OPERA TING & SERVICE MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .
2 INTRODUCTION This equipment supplies a liquid mix to the hoppers on the CDS-2 or 3 dispensers. It is for indoor use only on a sturdy counter or shelf.
3 00656.0000 00986.0000 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 29793 080102 10.
4 OPERA TING INSTRUCTIONS 1. On the CDS control panel, make the following switch settings: a) POWER- "ON" b) DAY/NIGHT- "DAY" 2. Pull the Powder Auto-Fill fully forward on its sup- port rails and open the door.
5 ADJUSTMENTS When using the Powder Auto-Fill with a new powdered granita mix, follow the procedure outlined below to adjust the Powder Auto-Fill to produce the correct recipe.
6 CLEANING RECOMMENDED DAILY CLEANING AND MAINTENANCE TIPS This should be done in conjunction with the recommended weekly cleaning of your CDS-2 or CDS-3 machine. Removing and cleaning the whipper chamber (once a day): 1. Open the cabinet door. 2. Pull the mixing chamber out of the whipper cham- ber.
7 F AUL T LIST Door Lamp Fault ON Normal operation - Powder Auto-Fill ready to dispense Flashes ON/OFF at 50% duty cycle Low product level in Powder Auto-Fill hopper T wo flashes about every 2 seconds.
8 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.
9 TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY PROBLEM Product level in CDS is lower than level Probe - CDS running; Powder Auto-Fill door lamp flashes two times Product level in CDS is lower than le.
10 TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY PROBLEM Powder Auto-Fill will not dispense product Dripping from dispense tip Water flows continuously 1. No water 2. No power or incorrect voltage to the dispenser. 3. Dispense Solenoid Valve 4. Control Board and Probe 5.
11 TROUBLESHOOTING (cont.) PROBABLE CAUSE REMEDY PROBLEM Product overflows CDS hopper Weak product Dispenser is making unusual noises Display not lit 1. Control Board and Probe 2. Dispense Solenoid Valve 1. Whipper Motor 2. Frother 3. Dispense Solenoid Valve 4.
12 SERVICE This section provides procedures for testing and replacing various major components used in this dis- penser should service become necessary.
13 SERVICE (cont.) FIG. 2 AUGER DRIVE COMPONENTS Location The auger drive components are located in the bot- tom of the hopper assembly . Removal, Cleaning and Replacement 1. Open the dispenser door. 2. Lift the hopper assembly over the retainer plates (16) on hopper support plate (12) and slide hopper assembly out the front of the dispenser.
14 FIG. 4 AUGER MOTOR P1922 AUGER DRIVE MOTOR Location: The auger motor is located on the right rear of the motor assembly mounting panel. Test procedures: 1. Disconnect the dispenser from the power source. 2. Check the voltage across the positive (red wire) terminal and the negative (black wire) terminal on the auger motor with a voltmeter.
15 FROTHER AND MIXING/WHIPPER CHAMBER FIG. 6 FROTHER AND MIXING/WHIPPER CHAMBER P1923 Location: The frother is located behind the dispenser door, mounted on the front panel and inside the whipper chamber. Removal, Cleaning and Replacement: 1. Disconnect the dispenser from the power source.
16 SERVICE (cont.) WHIPPER MOTOR FIG. 8 WHIPPER MOTOR P1924 Location: The whipper motor is located on the back side of the whipper motor mounting panel. Test Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the white/red and white/brown wires of the main wiring harness from the black leads of the whipper motor.
17 SERVICE (cont.) when reconnecting wires. 13. Slide the slinger onto the motor shaft flush against the front panel. 14. Wash whipper chamber components in a mild solution of dish detergent using a bristle brush. 15. Rinse thoroughly and allow to dry before reinstall- ing in the dispenser.
18 SERVICE (cont.) CONTROL BOARD and LEVEL PROBE FIG. 11 CONTROL BOARD P1925 Location: The control board is located behind the rear panel, mounted on the back side of the hopper motor mount- ing panel. Test Procedure: Liquid Level Control 1. Disconnect the dispenser from the power source.
19 SERVICE (cont.) CONTROL BOARD and LEVEL PROBE (cont.) Test Procedure: Low Product Detect 1. Disconnect the dispenser from the power source. 2. Disconnect the twelve pin connector (J1) from the control board. 3. Check the voltage across pins 2 & 3 of the twelve pin connector on the wiring harness with a voltmeter.
20 J2 J1 J3 J6 J7 SERVICE (cont.) CONTROL BOARD and LEVEL PROBE (cont.) Removal and Replacement: 1. Disconnect the dispenser from the power source. 2. Remove the two plugs (J1 and J7) from the main wiring harness, the potentiometer plug (J3), the photo transistor plug (J6), and the photo LED plug (J2) from the control board.
21 SERVICE (cont.) TEST/SERVICE SWITCH FIG. 13 TEST/SERVICE SWITCH P1923 Location: The TEST/SERVICE switch is located on the left front of the whipper motor mounting panel. T est Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the wires from the switch terminals.
22 SERVICE (cont.) FIG. 15 MAIN POWER ON/OFF SWITCH MAIN POWER ON/OFF SWITCH P1923 Location: The main power switch is located inside the dis- penser on the right of the whipper motor mounting panel. Test Procedure: 1. Disconnect the dispenser from the power source.
23 SERVICE (cont.) LAMP CORD ASSEMBLY FIG. 17 LAMP CORD ASSY P1891 Location: The lamp cord assembly is located in the top of the dispenser. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Unplug the lamp cord assembly from lamp cord connector assembly.
24 SERVICE (cont.) LAMP CORD CONNECTOR If continuity is present as described, the lamp cord connector is operating properly . If continuity is not present as described, replace the lamp cord connector . Removal and Replacement: 1. Disconnect the lamp cord assembly from the lamp cord connector.
25 SERVICE (cont.) If continuity is present as described, the lamp is oper - ating properly . If continuity is not present as described, replace the lamp. Removal and Replacement: 1. Disconnect the lamp cord assembly from the lamp cord connector assembly in the top of the dis- penser.
26 SERVICE (cont.) TRANSFORMER FIG. 23 TRANSFORMER P1930 Location: The transformer is located under the hopper sup- port panel mounted to the left of the whipper motor. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the four pin connector from the main wiring harness from the four pin connector on the transformer.
27 SERVICE (cont.) POTENTIOMETER FIG. 24 POTENTIOMETER P1931 Location: The potentiometer is located under the hopper support panel mounted to the left of the whipper motor and mounted on a bracket. Adjustments can be made by removing the 0.50" plug located on the whipper motor mounting panel.
28 SERVICE (cont.) HOPPER LEVEL INDICATOR FIG. 25 HOPPER LEVEL INDICATOR P1932 Location: The photo transistor and LED are located on the hopper side panels mounted just below the hopper guide rails. Test Procedures: Refer to the section CONTROL BOARD and LEVEL PROBE for test procedures.
29 SERVICE (cont.) HOPPER SWITCH FIG. 26 HOPPER SWITCH P1933 Location: The hopper switch is located under the hopper support panel. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Open the dispenser door and remove the hopper. 3.
30 SERVICE (cont.) DOOR SWITCH FIG. 28 DOOR SWITCH P1934 Location: The door switch is located on the right side panel under the housing top cover. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the twelve pin connector (J1) from the control board.
31 SERVICE (cont.) PRESSURE REGULATOR and NEEDLE VALVE FIG. 30 PRESSURE REGULATOR and NEEDLE VALVE P1935 Location: The pressure regulator and needle valve are located inside the rear panel at the bottom of the dispenser.
32 SERVICE (cont.) FIG. 31 DISPENSE SOLENOID VALVE P1935 DISPENSE SOLENOID VALVE Location: The dispense solenoid valve is located on the left side of the dispenser base inside of the rear cover. Test Procedures: 1. Disconnect the dispenser from the power source.
33 120 VOLTS AC - 2 WIRE SINGLE PHASE, 60 HZ 29780.0000A 5/99 © 1999 BUNN-O-MATIC CORPORATION M BLK RED WHI/BRN BLK VIO J7 J1 J6 PNK C O N T R O L P C B O A R D WHI/RED WHI GRN GRN ORN ORN WHI BLK WH.
34 29793 011500 WIRING DIAGRAMS 230 VOLTS AC - 2 WIRE SINGLE PHASE, 50 HZ 29780.0001B 10/99 © 1999 BUNN-O-MATIC CORPORATION M BLK RED WHI/BRN BLK VIO J7 J1 J6 PNK C O N T R O L P C B O A R.
Een belangrijk punt na aankoop van elk apparaat Bunn CDS-2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bunn CDS-2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bunn CDS-2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bunn CDS-2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bunn CDS-2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bunn CDS-2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bunn CDS-2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bunn CDS-2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
