Gebruiksaanwijzing /service van het product G9-2T HD van de fabrikant Bunn
Ga naar pagina of 20
BU N N ® OPERA TING & SER VICE MANU AL BUNN-O-MA TIC CORPORA TION OF CANAD A L TD . 280 INDUSTRIAL P ARKW A Y SOUTH AURORA, ONT ARIO. L4G 3T9 PHONE: (905) 841-2866 F AX: (905) 841-2775 10218.7000 3/00 ©1994 Bunn-O-Matic Corporation P E R S O N A L IN J U R Y H A Z A R D .
2 CONTENTS Introduction .............................................................................. 2 Warranty ................................................................................... 2 User Notices ......................................
3 USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. #05942.0000 DISPENSE TIME (Seconds) DISPLAY Increase Decrease Readout will be displayed for 5 minutes.
4 ELECTRICAL REQUIREMENTS This grinder has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. OPERA TING CONTROLS Off/On/Start Switch OFF - (upper position) Switching to this position stops all operation of the grinder .
5 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur faces on Bunn-O-Matic equipment. Care should be taken not to scratch the hopper or windows with any abrasive material. Regular cleaning will keep your grinder looking new for years.
6 ADJUSTMENTS The grind can be set from very fine to ver y coarse. The amount may be adjusted for use in most commer - cial coffee brewers. The following procedures should be used to make adjustments. A change in the burr adjust- ment will also change the amount dispensed.
7 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T ech- nical Service Department.
8 TROUBLESHOOTING (cont.) Problem Grinder will not start. Remedy (A) Plug-in the grinder . (B) Check the voltage at the wall outlet with a voltmeter . It must be 120 volts ac. (A) Momentarily press the Off/On/ Start switch to the “ST AR T” (lower) position.
9 Probable Cause 3. Relay 1. Hoppers 2. Bottoms of hoppers Remedy Refer to Service - Relay for testing procedures. See page 14. Begin each grind cycle by visually inspecting the hoppers for ample supplies of whole bean coffee. Foreign materials must not block the openings at the bottom of the hoppers.
10 The rear panel is attached with eight 8-32 slot- ted head screws. The hopper assembly is attached with four 6- 32 slotted head screws with locking nuts located on the sides of the housing near the center and rear . Removal of the hopper will also require disconnec- tion of the solenoid wires from the grinder wiring har - ness.
11 SERVICE (cont.) Off/On/Start Switch Location: The Off/On/Start switch is located to the left side on the front of the housing above the upper front inspection panel. T est Pr ocedure: 1. Unplug the grinder . 2. Remove the black wire from the switch.
12 SERVICE (cont.) Motor Location: The motor is located in the upper wrapper . T est Pr ocedure: 1. Remove the cover plate located on the right side of the housing. Press the red “Reset” button vis- ible through the opening. Listen carefully for a “click”.
13 SERVICE (cont.) Motor (cont.) Removal and Replacement - GRIND CHAMBER 1. Remove the two 1/4"-20 screws holding the front cover to the burr housing. Carefully remove the burr housing front cover . Inspect the adjusting screw to see if the thrust plug is worn.
14 SERVICE (cont.) Relay Location: The relay is located on the timer bracket in the grinder base. The bracket can be removed by loosen- ing the two 8-32 slotted head screws beneath the timer dial.
15 SERVICE (cont.) Slide Plate(s) Location: The slide plates are located on the solenoid mounting plate immediately beneath the hopper open- ings. The slide plates must always remain flat for proper operation. T est Pr ocedure: With the solenoid mounting plate attached to the hopper , push the solenoid plunger into the coil.
16 SERVICE (cont.) Snubber Location: The snubber is located at the back of the motor attached to the right side of the wiring harness. Removal and Replacement: 1. Remove the snubber wires from the motor ter - minals. 2. Cut the ties holding the snubber to the wiring harness.
17 Timer Location: The timer is located in the grinder base. T est Pr ocedure: 1. Unplug the grinder . 2. Check the voltage across contacts 1 & 2 of the larger connector on the timer board with a volt- meter whenever the grinder is plugged-in. Plug- in the grinder .
18 4. Check the voltage across contacts 2 & 6 of the larger connector on the timer board with a volt- meter when the control switch is in any position except “OFF” (center). Plug-in the grinder . The in- dication must be 120 volts ac. 5. Unplug the grinder .
19 P614 1 8 P4 P1 1 8 3 1 P2 P3 1 11 BLK to Cordset BLK to Off/On/Start Switch WHI/BLK to Cordset WHI/GRN to Relay Coil WHI/ORN to Left Solenoid WHI/YEL to Right Solenoid WHI/RED to Off/On/Start Switc.
20 BLU VIO YEL GRY TAN ORA WHI/BLK RED/BLK WHI/GRN WHI/ORA WHI/YEL WHI/RED WHI/BLK BLK WHI/RED WHI/BLU M K1 SOL 1 RT SOL 2 LT SNUBBER L2 L1 WHI/BLU WHI/BLK YEL 120 VOLTS AC 2 WIRE SINGLE PHASE 60 HZ 10756.0000G 3/97 © 1993 BUNN-O-MATIC CORPORATION L1 N K1 N.
Een belangrijk punt na aankoop van elk apparaat Bunn G9-2T HD (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bunn G9-2T HD heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bunn G9-2T HD vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bunn G9-2T HD leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bunn G9-2T HD krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bunn G9-2T HD bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bunn G9-2T HD kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bunn G9-2T HD . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
