Gebruiksaanwijzing /service van het product JDF-4 van de fabrikant Bunn
Ga naar pagina of 32
JDF-4 S/N 0005473 & UP ! W A RN I N G Refrigeratio n Compress o r and Cond enso r Fan Motor only INST ALLA TION & OPERA TING MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIEL.
2 38218.1 020608 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0000 CHARGE T ype R134A, Amount 10 oz (283 gm) Design Pressures: High 335 psi (23 bar) (2.
4 INITIAL SET -UP CAUTION: The dispenser is ver y heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . Place the dispenser on a sturdy counter or shelf able to support at least 230 lbs. (104.3 kg). The JDF-4 is designed for indoor use only .
5 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD W A TER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water sour ce must be capable of producing a minimum flow rate of 3 fluid ounces (88.7 milliliters) per second.
6 OPERA TING CONTROLS FIG 2 Refrigeration Switch FIG 3 Sanitize Switch & Water V alves A. Sanitize Switch B. Water Bath V alve C. Main Water V alve (Early Models) C P2262.60 P2479 A B Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner .
7 OPERA TING CONTROLS (cont.) FIG 4 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow .
8 INITIAL FILL CAUTION: The dispenser must be disconnected from the power source throughout the initial fill except when specified in the instructions. 1. Remove drip tray assembly and splash panel from the dispenser . Set the drip tray back into place.
9 INITIAL FILL (cont) Ambient Concentrates (Optional) 1. Install an Ambient Concentrate Conversion Kit (BUNN-O-MA TIC part number 33699.0000) per the instruc- tions provided in the kit. 2. Attach the concentrate product hose to the appropriate concentrate line located behind the dispenser’ s splash panel.
10 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature.
11 CLEANING (cont) 6. Select the dispense stations by pressing the “Dispense Switch” for that station. Use the “+/Stop Switch” for portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense head selected.
12 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser . 2. Using a water spray , clean the air filter . Annually: Replace Pump T ubing CLEANING (cont) 38218.1 012207 NOTE: High volume applications may require tubing changes every 6 months.
13 ADJUSTMENT & OPTIONAL SETTINGS T otal Dispense Ratio Set Up Procedure 1. Adjust water flow as described in Water Flow T esting and Adjustment . Record water output setting for later reference on each dispense head. 2. Enter program mode by simultaneously pressing both hidden switches.
14 4. At the end of the 5 second period, the selected position will dispense water (no concentrate) for only 3 sec- onds. 5. Measure the water dispensed. 6. Adjust the water flow rate Fig 7, (clockwise to increase flow rate; counter clockwise to decrease flow rate) to the corresponding product mix ratio as follows: 7.
15 3. T o decrease the pump speed, press and hold the left-hand “Hidden Switch” (half-filled cir cle) and then mo- mentarily press the “Product Dispense Switch (“+/STOP Switch” for portion control dispensers). Each time the “Product Dispense” (“+/STOP”) Switch is pressed, the motor speed is decreased by one step (5 RPM.
16 1. Enter the “Pump Speed Programming” mode by simultaneously pressing both “Hidden Switches”. Note that the beeper sounds twice and that the “PROGRAM” indicator begins flashing.
17 ADJUSTMENT & OPTIONAL SETTINGS (cont) Password Protection The programming modes and ser vice lockout function may be password protected to prevent accidental or unauthorized access to these features. The dispenser is shipped from the factory with a password of “0” (no password.
18 Dispense Fault List “REFILL” indicator Beeper Fault 2 flashes 2 beeps Dispense station locked out. 3 flashes 3 beeps DISPENSE/RINSE sensing fault. 4 flashes 4 beeps DISPENSE/RINSE knob mis-positioned. 5 flashes 5 beeps Pump motor stalled/speed sensor inoperative.
19 Dip Switch Function List Dip Switch Controls Off On 1 “REFILL” indicator when “concentrate out” is detected. Inactive Active 2 Lockout dispense components when “concentrate out” is detected. Inactive Active ( Note ) 3 Number of positions that can dispense/rinse simultaneously .
20 Function # 0 1 2 3 4 101 102 103 104 7 8 9 10 11 12 13 14 15 16 17 18 27 28 29 30 31 32 33 34 50 51 52 53 54 55 75 76 77 78 99 100 Description Enter Password Set Pump 1 RPM (Concentrate A) Set Pump.
21 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department.
22 TROUBLESHOOTING (cont.) Check for "ON" position or no con- tinuity - replace switch. Clean or replace condenser filter . Replace fan motor or check fan blades for obstructions. Check compressor relay coil for 120vac. NOTE: Always check power with coil attached.
23 TROUBLESHOOTING (cont.) Dispense station not working "refill" LED and beep code. A) 3-Beep - Dispense/Rinse sens- ing fault. B) 4-Beep - Dispense/Rinse knob mis-positioned. Refill LED not extinguishing All stations dispense concentrate only 1.
24 TROUBLESHOOTING (cont.) Dispense station concentrate only Dispense station water only Dispense starts then stops or "refill" flashes and beeps 5 times. Replace solenoid (24vdc) or check wire connection between water valve and main control board.
25 TROUBLESHOOTING (cont.) Water leak filling drip tray or around dispense deck area Water leaking beneath machine Erratic spray during dispense Dispense nozzle dripping water Can't access programming 1. Initial fill/setup 2. Dispense deck 3. W ater pressure greater than 100psi 1.
26 TROUBLESHOOTING (cont.) Uni t is not work ing and n o beep /lig ht fault codes Difficulty brixing and/or weak bev- erage 1. Step-down transformer . 2. Main control board. 1. Product viscosity or too cold. 2. Low water pressure. 3. High water pressure.
27 Difficulty brixing and/or weak bev- erage Difficulty brixing bag-in-box 1. Pump tubing. 2. Bottle adapter assembly leaking NOTE: Leaking water into con- centrate bottle during rinse of any station. 3. Use of portable water pump. Vacuum leak Inspect, clean, or replace tubing and pump rotor/rollers for ease of rotation.
28 COOLANT SCHEMA TIC DIAGRAM CONDENSER SUCTION ACCUMULA TO R COMPRESSOR EV APORA TO R PROCESS TUBE FIL TER DRYER 38218.1 030306.
29 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY . LEFT LAMP ASSY . GRN GRN GRN BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOST AT K2 K2 COM P.
30 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 SOL SOL #4 DISPENSE SOL ICE WA TER DISPENSE TA N RED/BLK RED/BLK RED/BLK WHI/YEL WHI/BLU .
31 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 J5-1 J5-5 J5-10 J5-15 J5-19 J4-1 J4-5 J4-10 J4-14 J9-1 J9-6 RED WHI GRN/WHI GRN/BLK ORN/B.
32 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 RIGHT LAMP ASSY . LEFT LAMP ASSY . GRN 120V MODELS GRN GRN N AB AB AB L1 BLU BRN/BLK RED/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOST AT K2 K2 COMP .
Een belangrijk punt na aankoop van elk apparaat Bunn JDF-4 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bunn JDF-4 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bunn JDF-4 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bunn JDF-4 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bunn JDF-4 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bunn JDF-4 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bunn JDF-4 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bunn JDF-4 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
