Gebruiksaanwijzing /service van het product ULTRA-2 van de fabrikant Bunn
Ga naar pagina of 23
INST ALLA TION & OPERA TING MANU AL B UNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .
2 32080 031103 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. CONTENTS Introduction & W arranty .......................
3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 ! W ARNING DO NO T O VERLOAD CIRCUIT .
4 INITIAL SETUP CAUTION – The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 3. Remove the rear plastic plug from the trim strip between the hopper drip trays and loosen the auger motor cover screws.
5 11. Thoroughly rinse the hoppers and install them over the augers and cooling drums. 15. Set the lids on the hoppers. Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cords. 17. Assemble the drip tray . INITIAL SETUP (CONT .
6 OPERA TING CONTROLS There are five of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming.
7 1 3 PROGRAMMING Using the menu-driven display on the front of the dispenser , the operator has the ability to alter or modify various parameters such as beverage consistency and set day/night “ON/OFF” times. The operator is also prompted to check a variety of periodic service functions or even a step-by-step cleaning routine.
8 PROGRAMMING THE DISPENSER During normal operations, the Date, the Time, and the Serial Number toggle back and forth continuously . The following function screens are in the order they appear from the menu display . Each screen will have instructions and procedures to program the various functions of the dispenser .
9 Cleaning Guide This function leads the operator through a nine step cleaning process when answered YES (“ICE”). Depress GOURMET to display the next cleaning instruction. When entering this mode, the refrigeration system will automatically turn OFF .
10 Set Consistency This function allows the operator to adjust the ice consistency , or torque of each auger when answered YES (“ICE”). T wo screens will appear for left and right. The operator can scroll through a range of a minimum of1 (UL TRA) to a maximum of 16 (ICE).
11 T est Augers This function tests the operation of forward and reverse of each auger motor . Left auger appears first. Press the ICE hidden switch to toggle between OFF , FORWARD and REVERSE. Press GOURMET hidden switch to repeat the operation for the right auger motor .
12 Password From this screen, the operator must know the password before moving on to the remaining functions. The range is from 0 - 9999 with the factory default being 0 . Set Night Time/Set Day T ime The setting of the Day/Night mode allows the dispenser to “power down” during off hours.
13 Preventive Maintenance Complete? This function is used to reset a reminder message Preventive Maintenance Due every six months. The ma- chine will not shut down if service is not per formed. When the service is per formed and the message is answered YES (ICE), the time and date is recorded for another six months to elapse.
14 Day T o Clean Off (formerly Days....Disabled) This function allows the operator to program a cleaning schedule from 1 to 14 days. The default screen is 0 or DISABLED. Selecting - or UL TRA will prompt the screen Days T o Clean. Once a number of days is selected the screen will prompt two functions, CLEAN MESSAGE ONL Y or CLEAN LOCKOUT .
15 Switches Enabled This function allows the operator to lockout the touch pad. Selecting + (ON) provides no time delay on switches except for the center (GOURMET) hidden switch.
16 Restore Default? Answering YES (ICE) to this function returns the unit back to preset factory constants. 1. Set Consistency ? 10 2. Set Night Time - DISABLED 3. Set Day Time - DISABLED 4. 6 Month PM - ENABLE 5. Days....Disabled - DISABLED 6. T orque Adjust Lock - YES 7.
17 DISPLA Y TEMP & T ORQUE 0 0 36 36 ° 0 0 67 67 ° h 32080 053102 TEMP & TORQUE Press and hold for five seconds the UL TRA and ICE hidden switches to display the TEMP & TORQUE. The temperature of each cooling drum and the hot gas temperature will toggle back and forth.
18 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper . 2. Place the pre-mixed liquid product in the selected hopper . 3. a. Press and release the (ON/OFF) switch to power on the dispenser .
19 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER •W hether liquid concentrate or granulated powder , all product must be thoroughly mixed BEFORE adding it to the hoppers. • For best results with granita-type products, use only products with an apparent brix of 12 or higher .
20 10. Place all parts in a clean sink with mild hot water (120 ° F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller components and tight areas.
21 1. Install the seals over the flange at the rear of the cooling drums and press the seals firmly into place as shown. 2. Align the auger shafts with the augers. Push the augers as far as they will go and rotate them so the flat face of the auger shaft is aligned with the flat face of the auger nose.
22 J5-1 J6-1 J5-5 J5-10 J2-1 J2-5 J2-10 J2-16 1 16 J3-1 J3-5 J3-10 J3-12 J5-15 J5-20 J5-24 C O N T R O L B O A R D D I S P L A Y RED/BLK WHI/RED-.
23 J5-1 J6-1 1 J5-5 J5-10 J2-1 J2-5 J2-10 J2-16 1 16 J5-15 J5-20 J5-24 C O N T R O L B O A R D D I S P L A Y CLOCK RED/BLK BRN/WHI BRN/BLK BLK WHI VIO WHI/BLU WHI/BLU WHI/BLK-22 YEL-22 GRY ORN BRN-20 .
Een belangrijk punt na aankoop van elk apparaat Bunn ULTRA-2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bunn ULTRA-2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bunn ULTRA-2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bunn ULTRA-2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bunn ULTRA-2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bunn ULTRA-2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bunn ULTRA-2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bunn ULTRA-2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
