Gebruiksaanwijzing /service van het product 2545 van de fabrikant Bush Hog
Ga naar pagina of 100
© 201 1 Alamo Group Inc. $0.00 2545 Published 01/1 1 Part No. 50069203 OPERA T OR’S MANUAL BUSH HOG ® 2501 Grif fin A ve. Selma, AL 36703 334-874-2700 www .bushhog.com LOADER This Operator' s Manual is an integral p art of th e safe operation of this machine an d must be maintaine d with the un it at all times.
T o the Owner/Operator/Dealer All implement s with moving part s are potentially ha zardous . There is no substit ute for a c autious , safe-minded operator who recognizes the potential hazards and follows reason able safety practices.
T ABLE OF CONTENTS SAFETY SECTION ........ ................................................. .......................................... ........... 1- 1 General Safety Instructions and Practic es ................... ................ ................. .
MAINTENANCE SECTION ................. ...................................................................... ........... 5-1 Lubrication Schedule ................ ................ ............. ............. ................ ............. ............
Safety Section 1-1 SAFETY SECTION.
SAFETY 2545 01/11 Safety Section 1-2 © 201 1 Alamo Group Inc. SAFETY General Safety Instruct ions and Practices A careful operator is the best opera tor .
SAFETY 2545 01/11 Safety Section 1-3 © 201 1 Alamo Group Inc. SAFETY Never allow children to operate, ride on, or co me close to the T ractor or Implement.
SAFETY 2545 01/11 Safety Section 1-4 © 201 1 Alamo Group Inc. SAFETY Operator Safety Inst ructions and Practices Never operate the T r actor or Implement until you h ave read and completely underst and th is Manual, the T ractor Operator ’ s Manual, an d each of the Safety Messages found in the Manual or on the T ractor and Implement.
SAFETY 2545 01/11 Safety Section 1-5 © 201 1 Alamo Group Inc. SAFETY Equipment Operation Safety Instructions and Practices Use extreme caution when getting onto the Impl eme nt to perform r ep airs, maintenan ce and when removing accu mulated material.
SAFETY 2545 01/11 Safety Section 1-6 © 201 1 Alamo Group Inc. SAFETY BEFORE leaving the tracto r seat lower the implement, set the parking brake and/or set th e tractor transmission in p arking gear , disengage the PTO, stop th e engine, remove the key , and wait for all mo ving part s to stop.
SAFETY 2545 01/11 Safety Section 1-7 © 201 1 Alamo Group Inc. SAFETY For added safety when lif ting loads above the height of the operato r , install a certified Falling Object Prot ective S tructure. Shiftable loads, round bales, large loose items, and loade r attachmen ts can fall toward the operator resulting in serious injury or death.
SAFETY 2545 01/11 Safety Section 1-8 © 201 1 Alamo Group Inc. SAFETY Carry the loader and att achment low when transporting to reduce the potential of the tractor tipping ov er . T ransport on slopes on ly at slow speeds and use grad ual turning angles.
SAFETY 2545 01/11 Safety Section 1-9 © 201 1 Alamo Group Inc. SAFETY Use extreme care when piling material above 6 feet high. Material could shift and fall onto the operator or by st anders. Th e material could crush or suf focate the operator or byst ander resulting in serious in jury or death.
SAFETY 2545 01/1 1 Safety Section 1-10 © 201 1 Alamo Group Inc. SAFETY Be particularly car eful in transport. The Implement has ra ised and moved the cen ter of gravity to the front of the Power Unit increa sing the possibility of overturn and tipping forward.
SAFETY 2545 01/1 1 Safety Section 1-11 © 201 1 Alamo Group Inc. SAFETY Connecting or Disconn ecting Implement Safet y Instructions and Practices Do not stand or allow byst ander or coworkers between the loader and th e tractor while installing or disconnecting the loader from the tractor .
SAFETY 2545 01/1 1 Safety Section 1-12 © 201 1 Alamo Group Inc. SAFETY T ransporting Safety Inst ructions and Practices T ransport only at speeds where you can maint ain control of the equipment. Seriou s accident s and injuries can result fro m operating this equipment at high sp eeds.
SAFETY 2545 01/1 1 Safety Section 1-13 © 201 1 Alamo Group Inc. SAFETY Maintenance and Service Safet y Instructions and Practices Lower the loader to th e bed of the truck or tra iler when transporting the tractor and loader with a truck. Measure to ensure the tr ansport heigh t does not exceed the legal limit s.
SAFETY 2545 01/1 1 Safety Section 1-14 © 201 1 Alamo Group Inc. SAFETY Never work under the Imp lement, the framework, or an y lifted compo nent unless the Implement is secure ly supported or blocked up to p revent sudden or inad vertent fallin g which could ca use serious inju ry or even death.
SAFETY 2545 01/1 1 Safety Section 1-15 © 201 1 Alamo Group Inc. SAFETY S torage and Parking Safety Instructions and Practices Concluding Safety Instr uctions and Practices Avoid contact with ho t surfaces of the engine or muffler . Use gloves and eye p rotection when servicing hot component s.
SAFETY 2545 01/1 1 Safety Section 1-16 © 201 1 Alamo Group Inc. SAFETY Decal Location NOTE: Bush Hog supplies safety decals on this produ ct to promo te safe op era t ion.
SAFETY 2545 01/1 1 Safety Section 1-17 © 201 1 Alamo Group Inc. SAFETY ITEM P ART NO. QTY LEVEL DESCRIPTION 1. 5005741 1 2 LOGO Bush Hog 2. 50069074 2 MODEL 2545 3. 52740 2 W ARNING Oil Leaks 4. 52203 1 W ARNING Lock V a lv e in T r ansport 5. 52204 1 INSTRUCT Loader Positions 6.
SAFETY 2545 01/1 1 Safety Section 1-18 © 201 1 Alamo Group Inc. SAFETY Decal Description P/N 5005741 1 Logo: BUSH HOG (3.20” x 14.50” ) MODEL NAME: 2545 P/N 50069074 W A R N IN G! - DO NOT operate with oil leaks.
SAFETY 2545 01/1 1 Safety Section 1-19 © 201 1 Alamo Group Inc. SAFETY W ARNING! Lock valve when in transport or storage. P/N 52203 Loader Positions. P/N 52204 Loader Safety -Read, understand and follow the operation, wa rning, and safety instruction s in the Operator ’s Manual.
SAFETY 2545 01/1 1 Safety Section 1-20 © 201 1 Alamo Group Inc. SAFETY Crushing Hazard, Electr ocution Hazard, Falling Hazard. D468 Crushing Hazard D471 DANGER! - Use ROPS and seatbelt at all times. Add recommende d rear ballast. Operate tr actor at low speeds.
SAFETY 2545 01/1 1 Safety Section 1-21 © 201 1 Alamo Group Inc. SAFETY Slow Moving V ehicle Decal. Keep SMV reflector clean and visible. DO NOT transpo rt or operate without the SM V . P/N 03200347 W AR NIN G! - Crushing Haz ard. -T o A v oi d Serious Injury or Death Make sure attachment is securely attached to the loader .
SAFETY 2545 01/1 1 Safety Section 1-22 © 201 1 Alamo Group Inc. SAFETY Federal Laws and Re gulations This section is intended to explain in broad terms the conc ept and effect of federal laws and regulations conce rning employer and employee eq uipment operators.
Introduction Section 2-1 INTRODUCTION SECTION.
INTRODUCTION 2545 01/11 Introduction Section 2-2 © 201 1 Alam o Group Inc. INTRODUCTION This 2545 Loader is des igned with care and built with quality materials by skilled workers. Proper assembly , maintenance, and ope rating practices, as described in this manual, will help t he owner/operator get years of satisfactory service from the machine.
INTRODUCTION 2545 01/11 Introduction Section 2-3 © 201 1 Alamo Group Inc. INTRODUCTION DO NOT use drugs or alc ohol immediately befo re or while operating the T ractor and Implement. Drugs and alcohol w ill affect an operator ’s alertness and coordination and theref ore af fect the operator ’s ability to operate the eq uipment safely .
INTRODUCTION 2545 01/11 Introduction Section 2-4 © 201 1 Alam o Group Inc. INTRODUCTION The Bush Hog 2545 Loade r is designed fo r two or four -wheel drive tracto rs. They are intend ed to lif t only loo se materials that will fit in the bucket. All cylinders are dou ble-acting.
INTRODUCTION 2545 01/11 Introduction Section 2-5 © 201 1 Alamo Group Inc. INTRODUCTION Attention Owner/Operator BEFORE OPERA TING THIS MACHINE: 1. Carefully read the Operator’s Manual, com pletely underst and the Safety Messages and instructions, and know how to operate correctly both the tractor and implement.
.
Assembly Section 3-1 ASSEMBL Y AND CONNECTING THE LOADER SECTION.
ASSEMBLY 2545 01/11 Assembly Section 3-2 © 201 1 Alam o Group Inc. ASSEMBL Y Assembly Instructions T o avoid injury during installation of the load er att achment, do not allow byst anders withi n 10 feet of load er or attachment. Always wear safety glasses when removing or installing buckets.
ASSEMBLY 2545 01/11 Assembly Section 3-3 © 201 1 Al amo Group Inc. ASSEMBL Y Do not use an attachment tha t is not securely attached to th e quick hitch, The attachment could fa ll resu lting in severe crushing injuries or death to the operat or or bystander s.
ASSEMBLY 2545 01/11 Assembly Section 3-4 © 201 1 Alam o Group Inc. ASSEMBL Y Proper Ballasting and Wheel S p acing S pread fro nt wh ee ls to m axim u m distance. S pread rea r wh ee ls to maxim u m dis tance. Add rear wheel weight, rea r ballast box or implement.
ASSEMBLY 2545 01/11 Assembly Section 3-5 © 201 1 Al amo Group Inc. ASSEMBL Y Dismounting and Mounting Mid-Mount Loader Mounting Loader Mounting is basically reve rse of dis mounting. 1. Slowly drive tractor into loader ap pr oximately 6” from loader mount s.
ASSEMBLY 2545 01/11 Assembly Section 3-6 © 201 1 Alam o Group Inc. ASSEMBL Y 6. Set parking br ake. Inser t two 1” hit ch pins a nd linch pins. 7. Remove linch pins and clevis pins from parking stands, rot ate stands into storage position and secure with clevis pins and lin ch pins.
ASSEMBLY 2545 01/11 Assembly Section 3-7 © 201 1 Al amo Group Inc. ASSEMBL Y Att aching Pin on Bucket Material bucket can be insta lled using tool ordinarily available. 1. Attach bucket to lift boom frame and cylinde rs with four 1” pins, using a 3/8 should er bolt and 3/8 lock nut to secure ea ch pin.
ASSEMBLY 2545 01/11 Assembly Section 3-8 © 201 1 Alam o Group Inc. ASSEMBL Y 6. Remove linc h pins and 1” hit ch pins from loader upright. 7. S tart tractor eng ine and release brakes. Retract bucket cylinders to allow parking stands to cont act ground.
ASSEMBLY 2545 01/11 Assembly Section 3-9 © 201 1 Al amo Group Inc. ASSEMBL Y Assembling Quick Att ach Device Quick attach device can be installed using tools ordinarily availa ble . T orque all hardware to spec ifications listed in loader operator’s manual.
ASSEMBLY 2545 01/11 Assembly Section 3-10 © 201 1 Alam o Group Inc. ASSEMBL Y Inst alling Quick Att ach Device 1. Fasten quick att ach device to lower boom arms and bu cket tilt cylin ders using 1” x 4-3 /8” anti-ro t ation pins, 3/8” x 3/4” shoulder bo lt s, and 3/8” lock nut s (supp lied with loade r).
ASSEMBLY 2545 01/11 Assembly Section 3-11 © 201 1 Al amo Group Inc. ASSEMBL Y Connecting Att achment When Connecting an Att achment to the Loader Quick Hitch 1. Be sure both quick hitch pin levers are in the unlocked position, with the levers pointing up.
ASSEMBLY 2545 01/11 Assembly Section 3-12 © 201 1 Alam o Group Inc. ASSEMBL Y 5. On level g round, tilt the attachment down 90 degree s and lower it to the groun d. L ower th e lo ad er fu rthe r to slightly raise the front of th e tractor of the tractor off the ground.
Operation Section 4-1 OPERA TION SECTION.
OPERATION 2545 01/11 Operation Section 4-2 © 201 1 Alamo Group Inc. OPERA TION BUSH HOG 2545 LOADER OPERA TION INSTRUCTIONS Y our Loader should now be assembled an d inspected for any evidence of defe ctive or damaged p arts before use. Any evidence of damage should be reported to your dealer immediately .
OPERATION 2545 01/11 Operation Section 4-3 © 201 1 Alam o Group Inc. OPERA TION 1. S t andard Equipment and Specifications S pecifications will vary w ith tire si ze, hydraulic system and bucket used.
OPERATION 2545 01/11 Operation Section 4-4 © 201 1 Alamo Group Inc. OPERA TION 2. Operator Requirement s DO NOT use drugs or alc ohol immediately befo re or while operating the T ractor and Implement.
OPERATION 2545 01/11 Operation Section 4-5 © 201 1 Alam o Group Inc. OPERA TION Never run the T ractor engine in a closed building or with out adequate ventilation.
OPERATION 2545 01/11 Operation Section 4-6 © 201 1 Alamo Group Inc. OPERA TION 3. T ractor Requirement s Safe operation of the unit is the responsibility of a qualifi ed operator .
OPERATION 2545 01/11 Operation Section 4-7 © 201 1 Alam o Group Inc. OPERA TION T ractor Requirement s and Cap abilities • ASABE approved Roll-Over Protective S tru cture (ROPS) or RO PS cab and seat belt. • Tractor Safety Devices ...............
OPERATION 2545 01/11 Operation Section 4-8 © 201 1 Alamo Group Inc. OPERA TION 4. Getting On an d Off the T ractor 4.1 Boarding the T ractor T o ens ure tractor stab ility when operating add wheel ballast or rear weights to rear tra ctor tires. For better stability , use tractor with wide front axle rather than tricycle fron t wheels.
OPERATION 2545 01/11 Operation Section 4-9 © 201 1 Alam o Group Inc. OPERA TION 4.2 Dismounting the T ractor Use both hands and equippe d handrails and steps for supp ort when boarding the tractor . Never use control levers for support wh en mounting the tractor .
OPERATION 2545 01/11 Ope ration Section 4-10 © 201 1 Alamo Group Inc. OPERA TION 5. St arting the T ractor Never run the T ractor engine in a closed building or with out adequate ventilation. T he exhaust fumes can be hazardou s to your health. (SG-23) S tart tractor only when pr operly seated in the T ractor seat.
OPERATION 2545 01/11 Ope ration Section 4-11 © 201 1 Alam o Group Inc. OPERA TION 6. Pre-Operation Inspection and Service Periodically inspect all moving part s for wear and replace whe n necessary with au thorized service part s. Look for loose fastener s, worn or broken p arts, and leaky or loose fittings.
OPERATION 2545 01/11 Ope ration Section 4-12 © 201 1 Alamo Group Inc. OPERA TION 6.2 Loader Pre-Operation Inspection/Service 6.1 T ractor Pre-Operation Inspection/Service Refer to the tr actor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed accordi ng to the manufacturers recommenda tions.
OPERATION 2545 01/11 Ope ration Section 4-13 © 201 1 Alam o Group Inc. OPERA TION Before operatio n, a complete inspection and service is required to e nsure the loader is in a good and safe working condition. Damaged and/or br oken part s should be repaired and /or replaced immediately .
OPERATION 2545 01/11 Ope ration Section 4-14 © 201 1 Alamo Group Inc. OPERA TION LOADER BOOM ASSEMBL Y • Inspect condition of each arm se ction weldment • Ensure all pins are in pl ace. • Ensure all bolt s and screws are properly installed. • Check condition of bushings at boom pivot points.
OPERATION 2545 01/11 Ope ration Section 4-15 © 201 1 Alam o Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection T ractor ID#:___________ _____________Make:________________________ Date:_________.
OPERATION 2545 01/11 Ope ration Section 4-16 © 201 1 Alamo Group Inc. OPERA TION FRONT END LOADER PRE- OPERA TION Inspection Front End Loader ID#_______________Make____________________ Date__________.
OPERATION 2545 01/11 Ope ration Section 4-17 © 201 1 Alam o Group Inc. OPERA TION 7. Driving the T ractor and Loader Be careful when oper ating or transporting th is equipme nt to prevent the Implement from running into or striking sign post s, guard rails, concrete abutment s or other solid objects.
OPERATION 2545 01/11 Ope ration Section 4-18 © 201 1 Alamo Group Inc. OPERA TION Safe tractor transport requ ires the operator p ossess a thorough knowledg e of the model be ing operated and precautions to t ake while driving with a n attached impl em ent.
OPERATION 2545 01/11 Ope ration Section 4-19 © 201 1 Alam o Group Inc. OPERA TION Do not raise the loader on a hillside. Do not transport across a slope with a raised loader . When the loader is raised, the center of gravity of the tractor and loader is ra ised increasing the pote ntial for the tractor to tip over .
OPERATION 2545 01/11 Ope ration Section 4-20 © 201 1 Alamo Group Inc. OPERA TION Do not raise the loade r into an overhead str ucture or allow a raised att achment to contact overhead st ructures. S udden or unex pected contact w ith an overhe ad structure could result in serious injury .
OPERATION 2545 01/11 Ope ration Section 4-21 © 201 1 Alam o Group Inc. OPERA TION Do not use an attachment tha t is not securely attached to th e quick hitch, The attachment could fa ll resu lting in severe crushing injuries or death to the operat or or bystander s.
OPERATION 2545 01/11 Ope ration Section 4-22 © 201 1 Alamo Group Inc. OPERA TION Do not use loader a s a jack to raise the tractor tires off the gr ound. The loader co uld fail causing the tractor and loader to fall to the ground resulting in serious inju ry .
OPERATION 2545 01/11 Ope ration Section 4-23 © 201 1 Alam o Group Inc. OPERA TION Always have a heavy att achment, such as a bu cket mounted on loader when it is removed from tractor . It is important not to put excessive weight on parking st ands with lift cylinder retr action.
OPERATION 2545 01/11 Ope ration Section 4-24 © 201 1 Alamo Group Inc. OPERA TION 8.1 Operating the Loader The following text and illustrati ons offer suggested loader an d tractor operating techniques. FILLING THE BUCKET Approach and enter th e pile with a level bucket.
OPERATION 2545 01/11 Ope ration Section 4-25 © 201 1 Alam o Group Inc. OPERA TION Lift and roll back of bucket will increase efficiency because... A level bucket throughout the lif ting cycle resists bucket lift and increa ses breakaway ef f ort. NOTE: Do not be concerned if the bucket is not completely filled durin g each pass.
OPERATION 2545 01/11 Ope ration Section 4-26 © 201 1 Alamo Group Inc. OPERA TION CARR YING TH E LOAD Position bucket just below tractor hood for maximum stability and visib ility , whether bucket is loaded or empty . Use extreme care when ope rating loader on a slope, keep bucket as low as possible.
OPERATION 2545 01/11 Ope ration Section 4-27 © 201 1 Alam o Group Inc. OPERA TION DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle. Move tractor in as close as possible to side of vehicle, then dump bucket. LOWERING THE BUCKET After bucke t is dumped, back away fro m vehicle while lowering and rolling back bucket.
OPERATION 2545 01/11 Ope ration Section 4-28 © 201 1 Alamo Group Inc. OPERA TION OPERA TING WITH FLOA T CONTROL During hard sur face operation, keep bucket level and put lift control in flo at position to permit bucket to float on workin g surface. If hy draulic down pressure is exerted on bucket, it will wear faster than normal.
OPERATION 2545 01/11 Ope ration Section 4-29 © 201 1 Alam o Group Inc. OPERA TION Side cutting is a good technique for cutting down a big pile. If the pile sides are too high a nd liable to cause cave-in, use loader to break do wn the sides until a slot can be cut over the top.
OPERATION 2545 01/11 Ope ration Section 4-30 © 201 1 Alamo Group Inc. OPERA TION It is important to keep the bucket level when approaching a bank or pile. This will help prevent gouging the work ar ea . PEELING AND SCRAPING Use a slight bucket angle, travel forward and hold lift control forward to st art the cut.
OPERATION 2545 01/11 Ope ration Section 4-31 © 201 1 Alam o Group Inc. OPERA TION Make additional passes until desired dep th is reached. Dur ing each pass, use only buck et control while working depth. This will allow you to concentrate on controlling bu cket angle to mainta in a precise cut.
OPERATION 2545 01/11 Ope ration Section 4-32 © 201 1 Alamo Group Inc. OPERA TION BACKFILLING Approach pile wit h a level bucket. Poor methods actually move no more dirt and make it more diff icult to hold a level grade. Do not use bucket in dumped position for bulldozing.
OPERATION 2545 01/11 Ope ration Section 4-33 © 201 1 Alam o Group Inc. OPERA TION Leave dirt in bucket. Dumping o n each pass wastes time. Operate tractor at righ t angles to ditch.
OPERATION 2545 01/11 Ope ration Section 4-34 © 201 1 Alamo Group Inc. OPERA TION Leave dirt which drif ts over side of bucket for final cleanup. Pile dirt on high side for easier backfilling on a slope.
OPERATION 2545 01/11 Ope ration Section 4-35 © 201 1 Alam o Group Inc. OPERA TION 8.2 Operating Bale Spear (Optional Att achment) Operate bale spear using extreme caution. Sh arp po ints on bale spea r can cause serious injury or death. Because of size and weight of large b ales, extreme care must b e taken in handling them.
OPERATION 2545 01/11 Ope ration Section 4-36 © 201 1 Alamo Group Inc. OPERA TION Carry bales as low to th e ground as possible to allow maximum visibility and avoid tipping. 9. Loader Storage Never allow children to play on or around T ractor or Implement.
OPERATION 2545 01/11 Ope ration Section 4-37 © 201 1 Alam o Group Inc. OPERA TION 10. T ransporting the T ractor and Implement Never allow children or other persons to ride on the T ractor or Implement. Falling off can result in serious injury or death.
OPERATION 2545 01/11 Ope ration Section 4-38 © 201 1 Alamo Group Inc. OPERA TION In case of mechanical dif f iculty during operation, place th e transmission in the park position, set the parking brak e, shu t dow n all po we r , inc l ud ing th e PTO and the eng ine and remove the key .
OPERATION 2545 01/11 Ope ration Section 4-39 © 201 1 Alam o Group Inc. OPERA TION 10.1 T ransporting on Public Roadways Make cert ain that the “Slow Moving V ehicle” (SMV) sign is inst alled in such a wa y as to be clearly visible and legible.
OPERATION 2545 01/11 Ope ration Section 4-40 © 201 1 Alamo Group Inc. OPERA TION 10.2 Hauling the T racto r and Implement Before transporting a loade d tractor and imple ment, measure the height and width dimension s and gross weight of the complete loaded unit.
OPERATION 2545 01/11 Ope ration Section 4-41 © 201 1 Alam o Group Inc. OPERA TION 1 1. T roubleshooting Guide TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Loader slow or will not lif t Hydraulic oil too heav y . Change to proper oil. and/or dump Oil filter plugged.
OPERATION 2545 01/11 Ope ration Section 4-42 © 201 1 Alamo Group Inc. OPERA TION PROBLEM POSSIBLE CAUSE REMEDY Insufficie nt lift cap acity Load is greater than boom Check loade r specifica tions. lif t cap acity . Improper hydraulic pump Repair or replace pump.
Maintenanc e Sec tio n 5- 1 © 201 1 Alam o Group Inc. MAINTENANCE SECTION.
MAINTENANCE 2545 01 /11 Maintenance Section 5-2 © 201 1 Alam o Group Inc. MAINTENANCE Never interfere with factory-set hydraulic calibrations. Any change in calibra tion could cause a failure of the eq uip m en t an d may re su lt in injury . (SBH-13) READ, UNDERST AND, and FOLLOW the following Safety Messag es.
MAINTENANCE 2545 01 /11 Maintenance Section 5-3 © 201 1 Alam o Group Inc. MAINTENANCE NEVER perform maintenance benea th a raised loader unless lo ader is properly supported to prevent accident al lowering. Avoid co ntact with hot surfaces inclu ding hydraulic oil tanks, p umps, motors, valves and hose connections.
MAINTENANCE 2545 01 /11 Maintenance Section 5-4 © 201 1 Alam o Group Inc. MAINTENANCE Lubrication Schedule Before operating your L oader , take the time to inspect a nd repair any damage to the machine or tracto r .
MAINTENANCE 2545 01 /11 Maintenance Section 5-5 © 201 1 Alam o Group Inc. MAINTENANCE Daily Maintenance Regular maintenance of your loader and hydraulic system will insure maximum load er efficiency and long life. 1. Check fluid level of tracto r hydraulic syste m before starting each da y’s operation.
MAINTENANCE 2545 01 /11 Maintenance Section 5-6 © 201 1 Alam o Group Inc. MAINTENANCE Cylinder Service Loader cylinders are designed to be re liable and easy to service.
MAINTENANCE 2545 01 /11 Maintenance Section 5-7 © 201 1 Alam o Group Inc. MAINTENANCE Lif t and Bucket Cylinder Reassembly Note: Be careful not to dama ge seals and o -rings on edge s or hole s in cylinder tu be. Inspect and rem ove burrs and sharp edges if necessary befo re reassembly .
MAINTENANCE 2545 01 /11 Maintenance Section 5-8 © 201 1 Alam o Group Inc. MAINTENANCE 1. S tore loader with att achment securely attached. 2. Place dust caps on hydraulic qu ick couplers. 3. Do not remove att achment from stored loader . 4. Do not allow children to play on or around loader .
MAINTENANCE 2545 01 /11 Maintenance Section 5-9 © 201 1 Alam o Group Inc. MAINTENANCE Proper T orque for Fasteners The chart lists the cor rect tightening torque fo r fastener s.
MAINTENANCE 2545 01/11 Maintenance Section 5-10 © 201 1 Alam o Group Inc. MAINTENANCE.
MAINTENANCE 2545 01/11 Maintenance Section 5-11 © 201 1 Alam o Group Inc. MAINTENANCE.
LIMITED W ARRANTY Bush Hog warrants to the or iginal purcha ser of any ne w Bush Hog equipmen t, pur chase.
T O THE OWNER/OPERA T OR/DEALER T o keep your implement running ef ficiently and safely , read your manua l thoroughly and follow these d irections and the Safety Messages in this Manua l. The T able of Contents clearly id entifies each section wher e you can easily find the informa tio n yo u ne ed .
2545-SOM-01/1 1 P/N 50069203 Printed U.S.A 2545 LOADER.
Een belangrijk punt na aankoop van elk apparaat Bush Hog 2545 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Bush Hog 2545 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Bush Hog 2545 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Bush Hog 2545 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Bush Hog 2545 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Bush Hog 2545 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Bush Hog 2545 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Bush Hog 2545 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
