Gebruiksaanwijzing /service van het product 9A656-04 ATM Module van de fabrikant Cabletron Systems
Ga naar pagina of 44
9032031-01 SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide.
.
i Notice Notice Cabletron Systems r eserves the right to make changes in speciÞcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made.
Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation.
iii Notice Dec laration of Conf ormity Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer Õs Name: Cabletron Systems, Inc. Manufacturer Õs Address: 35 Industrial W ay PO Box 5005 Rochester , NH 03867 European Repr esentative Name: Mr .
Notice iv.
v Contents Chapter 1 Intr oduction Document Objectives .................................................................................................... 1-1 Overview ..................................................................................
Contents vi Chapter 4 LANVIEW LEDs ANIM LEDs ............................................................................................................ 4-3 Chapter 5 General Specifications Operating SpeciÞcations ..................................
1-1 Chapter 1 Intr oduction Document Objectives This document, the SmartSwitch 9500 9A656-04 A TM Module Hardwar e and Installation Guide , contains introductory , installation and speciÞcation information for the support of the 9A656-04 SmartSwitch Module.
Introduction 1-2 Overview The 9A656-04 (shown in Figure 1-1) is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four A TM Network Interface Modules (ANIMs) of any type can be plugged into the 9A656-04 to provide fr ont panel connectivity to the network.
1-3 Ov er view Figure 1-1. The 9A656-04 AN AN AN AN 2031_01.
Introduction 1-4 Features The features of the 9A656-04 ar e described in the sections below: Pr ocessor The 9A656-04 is equipped with an advanced Intel i960 micropr ocessor . This micropr ocessor provides signalling, SNMP management, and serves as the in-band management LAN Emulation Client (LEC).
1-5 Related Manuals LANVIEW LEDs The 9A656-04 uses LANVIEW , The Cabletron Systems built-in visual diagnostic and status monitoring system. W ith LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance.
Introduction 1-6 Getting Help For additional support related to this de vice or document, contact the Cabletron Systems Global Call Center: Before calling the Cabletron Systems Global Call Center , ha.
2-1 Chapter 2 Installing the 9A656-04 Module SmartSwitch 9500 modules can be installed in any of the slots that are available. T o install a module, proceed as follows: 1. Remove the blank plate covering the slot in which the 9A656-04 will be installed.
Installing the 9A656-04 Module 2-2 Figure 2-1. Installing the 9A656-04 2031_02 AN AN AN AN Circuit Card Card Guides Metal Back-Panel Plastic Locking T ab Plastic Locking T ab.
2-3 The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: ¥ Pressing the Reset switch twice within thr ee seconds causes the processor (i960) to reset.
Installing the 9A656-04 Module 2-4 The Module Car d DIP Switch An eight position DIP switch is located on the module car d as shown in Figure 2-3. The functions of the switches ar e listed in T able 2-1. ! CA UTION Do not toggle Switch 8 unless you intend to reset the user configured pass words to their f actor y default settings .
2-5 Installing an ANIM Installing an ANIM Figure 2-3 shows the location of the 4 motherboar d connectors, and the 16 standoff scr ews for the A TM Network Interface Modules (ANIMs). Figure 2-3 also shows the location of the Module Card DIP Switch. Figure 2-3.
Installing the 9A656-04 Module 2-6 The 9A656-04 module is shipped without ANIMs. T o install the ANIMs proceed as follows: 1. Remove the module if it is installed in the SmartSwitch 9500 chassis. T o remove a module, r elease (rotate outwar d) the top and bottom plastic locking tabs, then slide the module out of the chassis.
2-7 Installing an ANIM 5. Press straight down Þrmly on the ANIM until the pins slide all the way into the motherboard connector . Ensure that the ANIM seats ßush on the standoffs. 6. Secure the ANIM with the two screws saved in step 2 and the two screws supplied with each ANIM.
Installing the 9A656-04 Module 2-8.
3-1 Chapter 3 Operation The 9A656-04 provides switching between the fr ont panel interfaces (ANIMs) and the Cell T ransfer Matrix backplane located inside the SmartSwitch 9500 chassis.
Operation 3-2 A TM Cell T raffic Flo w in the 9A656-04 The 9A656-04 SmartSwitch utilizes several innovative features that r esult in a completely redundant, fault-tolerant design.
3-3 A TM Cell T raffic Flow in the 9A656-04 CTM (Cell T ransfer Matrix) ASICs The 9A656-04 has seven CTM ASICs that provide two interfaces each between the TDM Bus and the CTM Backplane located in the SmartSwitch 9500 chassis. Each interface is a full-duplex connection with a raw throughput capacity of 2 Gbps.
Operation 3-4 System Management Buses There ar e two management channels within the SmartSwitch 9500 system: ¥ SMB-1 ¥ SMB-10 These buses provide out-of-band management and inter -module management communication. SMB-1 Bus The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9500 chassis.
3-5 System Diagnostic Controller System Diagnostic Contr oller This diagnostic controller is composed of a Z-80 micr oprocessor and its supporting logic.
Operation 3-6.
4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figur e 4-1 are the LANVIEW LEDs of the 9A656-04 module. Refer to T able 4-1 for the full deÞnitions of 9A656-04 LED states.
LANVIEW LEDs 4-2 T able 4-1. SMB and CPU LEDs LED LED Color State DeÞnition SMB Green Functional Fully operational Amber Crippled Not fully operational (i.
4-3 ANIM LEDs The front panel LANVIEW LEDs indicate the status of the ANIM and may be used as an aid in troubleshooting. Shown in Figur e 4-2 are the LANVIEW LEDs of all ANIMs. Although there ar e several types of ANIMs, all share the same LANVIEW LEDs.
LANVIEW LEDs 4-4.
5-1 Chapter 5 General Specifications The speciÞcations for the 9A656-04 are detailed in the sections that follow . Operating Specifications En vironmental Requirements Operating T emperature 5¡C t.
General Specifications 5-2 Ph ysical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) W eight Unit: 1.36 kg. (3lb) Shipping: 1.
5-3 ANIM Specifications ANIM-21/3 The ANIM-21/3 provides a multimode Þber connection using a Duplex SC connector and a line rate of 155.52 Mbps. The speciÞcations for the ANIM-21/3 are listed in T able 5-1. Figure 5-1. ANIM-21/3 T able 5-1. ANIM-21/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.
General Specifications 5-4 ANIM-29/3 The ANIM-29/3 provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3 are listed in T able 5-2. Figure 5-2. ANIM-29/3 T able 5-2. ANIM-29/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.
5-5 ANIM Specifications ANIM-29/3LR The ANIM-29/3LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3LR are listed in T able 5-3. Figure 5-3. ANIM-29/3LR T able 5-3.
General Specifications 5-6 ANIM-31/2 The ANIM-31/2 provides a multimode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-31/2 are listed in T able 5-4.
5-7 ANIM Specifications ANIM-39/2 The ANIM-39/2 provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2 are listed in T able 5-5.
General Specifications 5-8 ANIM-39/2LR The ANIM-39/2LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2LR are listed in T able 5-6. Figure 5-6. ANIM 39/2LR T able 5-6.
5-9 ANIM Specifications ANIM-67/2 The ANIM-67/2 provides a coaxial cable connection using BNC connectors with a line rate of 45 Mbps. The speciÞcations for the ANIM-67/2 are listed in T able 5-7.
General Specifications 5-10 ANIM-77/2 The ANIM-77/2 provides a coaxial cable connection using BNC connectors with a line rate of 34 Mbps. The speciÞcations for the ANIM-77/2 are listed in T able 5-8.
5-11 ANIM Specifications ANIM-22/4 The ANIM-22/3 provides a Category 5 UTP connection using four RJ45 connectors with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-22/4 are listed in T able 5-9. Figure 5-9. ANIM 22/4 T able 5-9. ANIM-22/4 Specifications Parameter SpeciÞcation Number of Interfaces 4 Line Rate 155.
General Specifications 5-12.
Een belangrijk punt na aankoop van elk apparaat Cabletron Systems 9A656-04 ATM Module (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cabletron Systems 9A656-04 ATM Module heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cabletron Systems 9A656-04 ATM Module vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cabletron Systems 9A656-04 ATM Module leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cabletron Systems 9A656-04 ATM Module krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cabletron Systems 9A656-04 ATM Module bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cabletron Systems 9A656-04 ATM Module kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cabletron Systems 9A656-04 ATM Module . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
