Gebruiksaanwijzing /service van het product 222D van de fabrikant AEG
Ga naar pagina of 20
222 D Fume Extractor Hood Installation and Operating Instructions.
2 Printed on recycled paper. AEG putting words into action..
3 Contents Introduction 4 Extraction mode 4 Recirculation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 10 Wall mou.
4 2 Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
5 ● Move the lever L to position A Fig. 3 . ● When connecting up the hood using a telescopic wall pipe, you should use an uninflammable outlet hose ABS 120 (120 mm Ø) available as an accessory. Recirculation mode ● The air is filtered and recirculated through the front grid.
6 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp.
7 Technical details Dimensions Height x Width x Depth (in cm) 13 x 59,9 x 51 Weight N e t : 6,9 kg Gross: 7, 8 k g Maximum absorbed power: 205 W Motor absorption 1 x 125 W Lighting: 2 x 4 0 W Length o.
8 Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.
9 ● The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms. ● Hoods can only be used safely with appliances connected to a chimney if the room and/or .
10 Wall unit mounting ● Make the holes on the bottom of the cupboard, using the drilling template . ● From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance.
11 Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I , 1 as desired at points L . ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely.
12 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
13 ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames.
14 6 Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 6. ● To remove the grid, pull it forwards from the right and release it.
15 8 Removing the filter Open the grid and remove the stops M to take out the filter. See Fig. 7. Carbon filter ● The activated carbon filter should only be used if you want to use the hood in its filtering function. ● To do this you will need an original AEG activated carbon filter (see special accessories).
16 Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply.
17 What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3.
18 Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Y our call will be automatically routed to the Service Centre covering your post code area.
19.
LI02GB Ed. 05/02 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http:/ /www .aeg.hausgeraete.de © Copyright by AEG.
Een belangrijk punt na aankoop van elk apparaat AEG 222D (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AEG 222D heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AEG 222D vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AEG 222D leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AEG 222D krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AEG 222D bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AEG 222D kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AEG 222D . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
