Gebruiksaanwijzing /service van het product (VISM) van de fabrikant Cisco Systems
Ga naar pagina of 664
Corporate He adquarters Cisc o Syst ems , Inc . 170 West Ta sman Drive San Jos e, CA 95 134-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553- NETS (638 7) Fax: 408 526-4100 Cisco VISM Installati on and Configuration Guide R ele ase 3 .
THE SPECIFICATIONS AND INFORMATION REG ARDING THE PRODUCT S IN THIS MANUAL ARE SUBJE CT TO CHANGE WITHOU T NOTICE. ALL STATEMENTS , INFORMATION, AND RE COMMENDATIONS IN THIS MANUA L ARE BELIEVED TO BE ACCURAT E BUT ARE PRESENTED WITHOUT WARRANT Y OF ANY KIND, EXPRESS OR IMPLIED.
iii Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 CONTENTS Preface xii i Object ives xii i Audienc e xiii Document Organi zation xiii Relat ed D ocum ent atio n xiv Cisco MGX 885 0 (PXM45) Mul tiservi ce Switch Release 3 xiv MGX 8850 (PXM1) Multiser vice Swit ch Releas e 1.
Cont ent s iv Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Instal ling VISM-P R Cards in MGX 800 0 Series Cha ssis 1-13 MGX 8850 and MGX 8.
Content s v Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 CAS Proces sing in VoI P Switchi ng and Switc hed AAL2 PVC Oper ating Mode 3-6 CCS .
Cont ent s vi Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Config uring ECAN 4- 29 Config uring Ji tter 4-30 Config uring PNNI for AAL1/AA.
Content s vii Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Announce ment Dir ection 4-62 Broadca st Annou ncemen ts 4-6 3 Multip le An nounc.
Cont ent s viii Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 DSP Do wnlo ad F ailure 6-7 VISM Front Card/Bac k Card Mismatc h 6-8 Cannot U.
FI GURES ix Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 Figu re 1-1 VISM T1 and E1 Front Card s 1-2 Figu re 1-2 VISM-PR T1 and E1 F ro.
Figures x Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004 Figu re A-2 VISM Conf igur ed f or L oop C loc king A-3.
TABLES xi Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 Ta b l e 1 Cisco MGX 885 0 (PXM45) Mul tiservi ce Switch Release 3 Doc umentati on xiv Ta b l e 2 MGX 8850 (PXM1) Multiser vice Swit ch Releas e 1.
Tables xii Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004.
xiii Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 Preface This p refac e descr ibes the objecti ves, aud ience , org ani zation, and con vent ions of the Cisco VISM Inst allation and Conf igu ra tio n Guid e.
xiv Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Preface Related Documenta tion • Chapter 5, “CLI Commands,” describes th e syntax and s emantic s of each VISM comm and line interf ace c ommand.
xv Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Preface Relat ed Document ation MGX 8850 (PXM1 ) Multis ervice S witch R elease 1.2.10 The docum entation for the installat ion and opera tion of the MG X 8850 (PXM1) Mu ltiservice Swi tch is listed in Ta b l e 2 .
xvi Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Preface Related Documenta tion MGX 8250 Edge Concen trator Release 1.2.10 The do cumentation f or the instal lation a nd operat ion of t he MGX 82 50 Edge Conc entrator is listed in Ta b l e 3 .
xvi i Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Preface Convent ions The documentation listed in Ta b l e 5 contain addit io nal in f ormatio n relate d to the oper at ion of th e Cisco VISM prod uct .
xviii Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Preface Obtain ing Do cument ation Note Means r eader t ake note . Not es co ntain helpf ul s uggest ions or r efer ence s to m ateri als not co ntain ed in this manual.
xix Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Preface Obtaining Technical Assistance Y ou ca n submit c omment s by using the respon se c.
xx Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Preface Obtainin g Addi tional Pub lications and Informat ion TAC Case Priority Definitions T o ensure that all cases are repor ted in a standard for mat, Cisco has estab lished case prior ity def initio ns.
xxi Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Preface Obtaining Additional Publications and Information • Int ernet Pr otocol J ourn al.
xxii Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Preface Obtainin g Addi tional Pub lications and Informat ion.
C HAPTER 1-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 1 Overview of the VISM and VISM-PR Card s This cha pter provides a ge neral introduct ion to VISM an d VISM- PR and descri bes the hardware and software mod ules, and installati on proced ures.
1-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Types Note Us ing the Ser vic e Resour ce Mo dul e ( SRM) a nd the 1 :N re dun dancy f eat ures , ot her phy sica l configurat ions ar e supp orted.
1-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards VISM an d VISM- PR Ca rd Types There are.
1-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Types Figu.
1-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards VISM a nd VISM-P R Card P hysical C hara.
1-6 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Features Figure 1-5 sh ows a simplif ied diagram of the VISM architect ure and its major compone nts.
1-7 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards VISM an d VISM- PR Card Feat ures • V oice ov er A TM (V oA TM ) usi n g AAL2 cell s—No Log ical L ink C ontrol /Subnetwo rk Access Pro tocol (LL C/SN AP) en capsu lat ion.
1-8 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Features • Line loopb ac k (D S1) toward the T DM lin es . • Channel lo opbac k (DS0) toward bo th t he T DM li nes and the A TM netwo rk.
1-9 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards VISM an d VISM- PR Card Feat ures Operat.
1-10 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Features Figure 1-6 shows th e major func tional bl ocks and inte rfaces fo r the V oIP switc hing an d swit ched AA L2 PVC operatin g mode s.
1-11 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards VISM an d VISM- PR Card Feat ures Call A gent Inter face The call ag ent interf ace con sists of CAS signaling o r CCS signaling and call control.
1-12 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s VISM and VISM-PR Card Features .
1-13 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Installing VISM Hardware and Software V oAAL2 SVC is su pport ed wit h the G.71 1, G.726 , G.
1-14 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Install ing VIS M Hardwar e and.
1-15 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Installing VISM Hardware and Software M.
1-16 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Install ing VIS M Hardwar e and.
1-17 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Installing VISM Hardware and Software The co nnecto r wiring is shown in Figure 1-10 .
1-18 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Install ing VIS M Hardwar e and Soft ware Step 3 Pull both of the e xtractor le ve rs out to the horizontal position.
1-19 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Installing VISM Hardware and Software S.
1-20 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Software U pgrades Software Upgrades VISM /VI SM- P R R el eas e 3.0 p rovid es a gr ac ef ul u pgr ad e pr oced ure f or th e f ol lowing re le as es :.
1-21 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Software Upgrades Step 4 Do wnload t h e sel ected f irmware f ile. T o upgrad e all VISM cards, proceed t o Step 4c.
1-22 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Software U pgrades This com mand cau ses the second ary VI SM or VISM-P R ca rd to reset a nd come u p in the standby state , runn ing th e ne w-re v fi rmwa re.
1-23 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Software Upgrades Boot Code Upgrade Pr .
1-24 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Software U pgrades Download VI SM-PR Boot Cod e and Fir mware t o PXM1E and PXM 45 T o download t he VISM-PR bo ot code and firmware to th e PXM1E or PX M45 card, use FTP .
1-25 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 1 Overv iew of the VISM and VISM -PR Cards Software Upgrades Step 6 T o commit the ne w do wnload to the VISM- PR card, ente r the commitre v command .
1-26 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 1 O vervie w of th e VISM a nd V ISM-P R Card s Software U pgrades Step 4 Ex ec.
C HAPTER 2-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 2 Telephony App lications Using VISM This chapte r describes the VISM card and the ways it is used in telepho ny applica tions to transport traditi onal TDM v oice traf f ic as digi tized v oice traf fic ove r A TM networ ks.
2-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 2 Telephon y Applicat ions Using VI SM Tandem Switch Offloadi ng When a call is initiated, the centr al of fi ce can use either th e Class 4 swi tch or VISM to handle th e call.
2-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 2 Telephony Applica tions Us ing VISM Multiserv ice Access Each of the two lower shelf c ellbuses can susta in a ban dwidth of one OC-3/ STM -1 link.
2-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapte r 2 Telephon y Applicat ions Using VI SM AAL2 T runkin g Figure 2-4 sh ows a tr unk with a V I SM-eq uippe d MGX 885 0 sh elf at eac h en d of the tru nk.
C HAPTER 3-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 3 VISM Functional Description The fu nctions performe d by VISM are desc ribed in.
3-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description TDM L ine-Han dling F unction Figur e 3-1 VISM Deta.
3-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Bearer P rocessing Fu nction Bearer Processing Fun c.
3-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Bearer Proc essing F unction • T emplate 3 — Support s G.71 1u, G.7 11a, G.7 26- 16k , G. 726 -24k, G .
3-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Signal ing Funct ion Jitter Control The VISM card uses v oice buf fers on the DSP to reduce jitter on outgoing v oice stream s.
3-6 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Signaling F unction Note Y ou can configure th e VISM c ard to support C CS signal ing wit hout V ISM card in v o lvement.
3-7 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Signal ing Funct ion Figure 3-3 shows the messages in volve d in CA S processing with the V oIP switching and switched AAL2 PVC operatin g mode s.
3-8 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Signaling F unction Figur e 3-4 CA S Signaling in Initiating and T er minating a Call Note Figur e 3-4 shows only the lo cal CAS aspects of c all setup.
3-9 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Signal ing Funct ion 5. When th e cal l ag ent rece ives the d ial ed n umb er , i t use s th e dia l pla n to com mun icat e wi th th e r emote call agent to set up the call .
3-10 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Signaling F unction Figure 3-5 sh ows the VISM PRI/backh aul pro cess. Figur e 3-5 PRI/Bac khaul P ath For R UDP link s betwee n VISM and the call ag ents, use a session with a session manage r .
3-11 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription ATM Voice Data P rocessing Fu nction Use the CLI PR.
3-12 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description ATM Vo ice Data Pr ocess ing Functio n 3. Encap sulated in an IP pack et. 4. Con verted to AAL5 A TM cells for transmissio n to an edge router on the network .
3-13 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription ATM Voice Data P rocessing Fu nction T o improv e reli ability , VISM support s two i ndependent O C-3 interf aces, eac h conne cted to a separate edge rou ter and eac h with its o wn PVC.
3-14 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description ATM Vo ice Data Pr ocess ing Functio n Figure 3-9 sh ows the p acketi zat ion pr ocess fo r AA L2 c el ls.
3-15 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Call Control Function Call Control Function Call con trol is use d in th e switc hed AAL 2 PVC o pera ting mode onl y and i s manage d by the ca ll ag ents.
3-16 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Call Control Function VISM suppo rts up to el e ven do main na mes and ea ch doma in name ca n hav e up to eight in ternal and e ight external IP addresses.
3-17 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Call Control Function xGCP Exten sions for AAL2 Swi.
3-18 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Call Control Function If an ala rm conditio n on a line is raised, a ll endpoint s on the line a re brought in to a for ced transition to OOS.
3-19 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Embedded VISM Ma nagement Fu nction Connectio n Adm.
3-20 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Embedd ed VISM Mana gement Func tion Figure 3-12 shows an example of a CWM VISM Card Config scr een with the card elem ents displa yed.
3-21 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 3 VISM Functional Des cription Embedded VISM Ma nagement Fu nction Figure 3-13 shows an exam ple of a CWM VI SM Card Co nf ig scree n with the VI SM feature s displaye d.
3-22 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 3 VISM Functional Description Embedd ed VISM Mana gement Func tion.
C HAPTER 4-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 4 Configuring VISM Features The c ommand line int erfac e (CLI ) is a D OS-like inte rface used to con fig ure VI SM cards.
4-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Connecting t o Cisco MGX 8000 Seri es Platform.
4-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Connecting to Cisco MGX 8000 Series Platforms Figur e .
4-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Connecting t o Cisco MGX 8000 Seri es Platforms Note The default user name is cisco . Y o u may change this username after your initial login is complete.
4-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Connecting to Cisco MGX 8000 Series Platforms 1.17 Empty Clear 1.18 Empty Clear 1.19 Empty Clear 1.20 Empty Clear 1.
4-6 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Configuring VI SM Features The CL I a llows you t o con figure a ll fea ture s an d func ti ons of V ISM.
4-7 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features T able 4-2 Mandatory Initial.
4-8 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Initial Card Level Configuration Y ou must complete the foll owi ng conf iguration tasks wh en you initia lly conf igure your VISM ca rd.
4-9 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 3 T ype the cnfvismmode co mman d, an oper -mo de argument value, an d press Ent er to configure th e VISM operati ng mode.
4-10 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • 3 = G.711u, G.711a, G.7 26-16k , G.726-2 4k, G.726- 32k, G.72 6-40k, G.
4-11 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 4 T ype the cnfvbdpol .
4-12 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Com ple te th e fo llowi ng step s to : • Add an d c on figure y our e ight T1 or E 1 lin e por ts on the VI SM back c ard.
4-13 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 3 T ype the cnfa l m c.
4-14 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Step 6 T ype the addlnloop comman d, a line-num ar gument v alue, a nd pr ess Enter to set a spec if ied line to the local l oopback stat e.
4-15 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 2 T ype th e cn fcl ksrc com mand , slot-num . po rt-nu m, and clk -type argument values, and pr ess Ente r to configure th e PXM card cl ock source .
4-16 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Note The y argument value is t he actua l slot number of the VI SM card.
4-17 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Note Y o u must includ e al.
4-18 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Add and Config.
4-19 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features – For template number 2: .
4-20 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • For templa.
4-21 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Com ple te th e fo llowin g.
4-22 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures – 15 = BC303.
4-23 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Configur ing TDM Si de Sign.
4-24 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Note The cnfcas paramsour ce command permits dif feren t CAS-relat ed timer v alues for dif ferent endpoints, b ut all are asso ciated with the same CAS v ariant.
4-25 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features • endpt- num : T ype the v alue used in Step 1 .
4-26 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Step 10 T ype .
4-27 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features • |sou r ce| (CAS va riant f ile location) : – 1 = Unsp ecified. If TFTP do main i s con f igured, t he loca tion is the TFT P server .
4-28 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • 2 = G.
4-29 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features • 5 = Loc al MIB, L CO list, remote SDP data list • 6 = Loc al MIB, rem ote SDP da ta list, LCO list Y ou hav e complete d assigning and conf igurin g the codec template .
4-30 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Step 4 T ype t.
4-31 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 3 T ype the cn fjtri nitdel ay command, the jitt er -buf fer-size ar gu ment v alu e, an d pres s Enter to specify the starting buf fer size.
4-32 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • The switc hed AAL2 PVC operating mode requi res you to set up as ma ny as 64 AAL2 PVCs connect ed to each remote lo cation s upporte d by the ne twork.
4-33 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features • conn- type (typ e of co.
4-34 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • service-ty.
4-35 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 2 T ype the cnfdefto s.
4-36 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • event-neg-.
4-37 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features – 5 = G.729a b – 6 = Clear cha nnel (V AD must be of f) – 7 = G.726-1 6k – 8 = G.
4-38 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • dtmf-trans.
4-39 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Configur ing a Vir tual Ci .
4-40 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures VISM/VISM -PR creates the prof ile tab le with t he def aults that a re listed in Ta b l e 4 - 5 .
4-41 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Comple te the following step s to assign a profile prefe rence and to modify th e packet period and SID v alue s of th e prof ile table , as ne cessary .
4-42 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Step 2 T ype t.
4-43 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features – 5 – 10 – 30 Step 4 .
4-44 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Y ou have compl eted con figuring t he swit che d AA L2 PV C op er ati ng mo de p aram eters.
4-45 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features 3. Configure gateway control prot ocols. 4. Configure ISDN PRI bac khaul (opti onal).
4-46 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures – 4 = Extern al first Step 2 If you are not using an externa l DNS to resol ve domain name s ( r esol-type = 1 in Step 1 ), pro ceed to Step 3 .
4-47 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Configuring Gateway Control Pr otocols Comp lete the fol lo wing steps to conf igure gat eway contr ol pr otoc ols.
4-48 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures • aal-conn- type : – 1 = AAL1 – 2 = AAL2 – 3 = Not applica ble Note Y o u must type 3 for t he aa l-conn- type argume nt if the netw ork-type argume nt = 1.
4-49 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 7 T ype th e cnfsrcppe.
4-50 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Conf igu rin g VIS M Feat ures Comple te the .
4-51 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Configuring VISM Features Step 6 T ype th e cn fses m.
4-52 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures Step .
4-53 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures • Added sup port for G.
4-54 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures • T.
4-55 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures Mid-Call DTMF.
4-56 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures This fe ature requir es you to add mo re th an one d omai n name and c onfigure these as re dundant call a gents or the same lo gica l M GC.
4-57 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures Y ou mus t pr o v i si o n t h e LA PD tru n k wh en usi ng this fea t ur e.
4-58 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures VISM Rele ase 3.0 allo ws you to conf igure provisio nal tone p lans if th e b uilt-in tone plan s do not m eet your appl ication need s.
4-59 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures FGD supp ort .
4-60 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures Confi.
4-61 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures • Pri v ate.
4-62 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures The G .72 3.1 c od ec, used in c om bina tion wit h the V ISM-PR c ard, sup por ts 14 4 ch annel s.
4-63 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures Broadcast Announcements VISM su pport s ann ounc eme nt r eque sts f or a sing le e ndpoi nt or conn ect ion.
4-64 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures When .
4-65 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures Call Agent-Controlled T.38 Fax The ca ll ag ent -con tr olled T .
4-66 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures Additional Support for MGCP 1.0 This re le ase expa nd s the supp ort for the Me dia Gateway Cont ro l Pro toco l (M GCP) 1.
4-67 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures • T ear down originate d or establi shed un idirecti onal res ource reservation s.
4-68 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures RTP C.
4-69 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 4 Configuring VI SM Features Confi guring Additiona l VISM Fe atures MGX 8000 Seri.
4-70 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Cha pter 4 Co nfig uri ng VIS M Fe at ures Configur ing Additio nal VISM Fe atures Addit.
C HAPTER 5-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 5 CLI Commands Command l ine inte rfac e ( CLI ) comma nd s al low you to c onfigure , mana ge, an d tr oub lesho ot V I SM to enable your applicati ons.
5-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands ? ? T o display some o r all c omman ds asso ciated with t he cur.
5-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addannpe rman ent addannperman ent T o conf igure an announce ment ser ver f ile an d associa ted codec type as perm anent, use the addannpermanent command in the V oIP switchi ng operating mode.
5-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addannpe rman ent Relat ed Comma nds Comman d Des cription cnfa nnageti me Configur es the time that a nonp ermanent announce ment is to remain v alid after it is p laced into the VI SM annou ncement c ache.
5-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addc asv ar addcasvar T o add a channel ass ociated sig naling (C AS.
5-6 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addca svar Exam ples The follo wing ex ample s ho w s tha t a win k st art CAS v ar iant called cas v ar is ad ded to a VISM c ard based upon i nformation c ontained in the wi nk_did_dod.
5-7 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addccs addccs T o add a common ch annel si gnaling ( CCS) ch annel (D chan nel) to a VISM card, use th e addccs comm an d in the switch ed A AL2 PVC an d A AL 2 tr unk ing opera ting mod es .
5-8 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addcid addcid T o add an AAL2 chann el iden tif ier (C ID) on a VISM ca rd, use t he addci d command in the AAL2 trunking op erat ing mode .
5-9 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addcid codec- type The type of coding/ decodi ng to be perf ormed on th e data stre am. It ca n be one of the follo wing valu es: • 1 = G .
5-10 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addcid Command Mode s AAL2 trunking Usage Guid elines Th is comm and establ ishes a rela tionshi p between a n endpoint an d an LCN /CID pair .
5-11 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addcid • The cur rent DSP tem plate must contai n the de sired codec type. This com mand can be used on an endp oint that has no asso ciated CAS variant.
5-12 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addcon addcon T o a dd a perma nent vir tual circ uit (PV C) con.
5-13 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addco n Command Mode s V oI P swi tchin g/trun king, swi tched AA L2 PV C, a nd A AL2 trun king Usage Guid elines Y o u mus t ex ecute the addport and addrscprtn comm ands before you use thi s comman d.
5-14 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addcon Exam ples Th e fol lowing example ad ds a ma ster co nnec tion a s t he pri ma ry ch anne l using AA L2 fo r beare r traffic.
5-15 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addconl oop addconloop T o s et a cel lbus c onn ec ti on t o l oca.
5-16 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands adddn adddn T o add a dom ain nam e (call ag ent na me, TFTP ser.
5-17 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addd n dspdn Displays the ar gument v alues of a call agent’ s domain numbe r .
5-18 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands adddnip adddnip T o add the IP addre sses for a dom ain nam e th.
5-19 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addendpt addendpt T o add an endpoi nt on a VISM card line, use the addendpt command i n the V oIP swit ching/trun king, switched AAL 2 PVC, and AAL 2 trunking opera ting modes.
5-20 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addendpt This comm and sen ds an RSIP messa ge to each ass ocia ted call agent i ndicating that the endpoin t is in service.
5-21 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addendpt loop addendptlo op T o place an endpoint in a lo opb ack c.
5-22 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addendpt s addendpts T o ad d multi ple co nsecutive number of e.
5-23 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addendpt s Command Mode s V oI P swi tch ing/t runki ng, sw itch ed.
5-24 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addendpt s This command sends a n RSIP message to eac h asso ciated ca ll agen t indica ting that the en dpoint s are in service.
5-25 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addl apd addlapd T o add a Link Access Pro tocol D cha nnel (LA PD) fro m a spec ified DS0 to a VISM c ard, use t he addlapd comm an d in V oIP sw itch ing/ tru nking o p erati ng mode .
5-26 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addlapdt runk addlapdtrunk T o add a Link Acc ess Protocol D chan nel (L APD) trunk t o a specific VISM card lin e, use the addlapdtrunk command i n the V oIP sw it chi ng/tru nking o per a ting m ode .
5-27 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addla pdt runk dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session. dsprudptrunks Displays the configura tion d ata o f all IS DN PRI ba ck haul RUDP session s.
5-28 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addln addln T o add a T 1 or E 1 line t o a VI SM card , use t he addln command in the V o IP switching/trunk ing, switched AAL2 PVC, an d AAL2 trunk ing operat ing modes.
5-29 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addlnlo op addlnloop T o set a spec if ied line of th e c urr en t .
5-30 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addmgc grpentry addmgcgrpent ry T o c on figure a cal l a gent a.
5-31 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addmgc grppr otocol addmgcgrpprotoc ol T o asso ciat e a call age n.
5-32 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addmgc grpprotoc ol Command Mode s V oI P switching/ trunking an d switched AAL 2 PVC Usage Guid elines Th is command allows you to add multiple protocols to the same redundancy group.
5-33 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addmgc grppr otocol dspmgcgrpparams Displays al l configured c all agent re dundancy group paramete rs. dspmg cgr ppr otoc ols Displays all co nfigured call agent redunda ncy group protocol s.
5-34 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addport addpo rt T o add a virtu al port betwee n the VISM and P.
5-35 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addrscpr tn addrscprtn T o add a resource part ition for a virtual .
5-36 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addrtpco n addrtpcon T o add a stat ic Rea l-T ime T ranspo rt Prot ocol (R TP) V oIP trun king connec tion , use the addrtpcon comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-37 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addrt pco n codec- type The ty pe of c oding/de coding to be perform ed o n the data str eam. I t can be one of the foll ow ing va lues: • 1 = G.
5-38 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addrtpco n Command Mode s V oI P swi tchin g/t runking Usage Guid elines Th e G.723. 1 codecs are supp orted for VISM-PR cards an d are not supp orted for VISM card s.
5-39 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addrt pco n cnfrtpcon Modifies an existing sta tic R TP V oIP t ru nking conn ec tion.
5-40 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addrudpt runk addrudptrunk T o add an ISDN PRI ba ckhau l Reliab.
5-41 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addrudp trunk dsprtpcnt Displays the bearer c ounters (s tatistics) fo r a specif ic R TP V oIP trunking connec tion. dsprtpcon Displays the con figurat ion data of a specif ic static R TP V oIP trunking connec tion.
5-42 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addses addses T o add a PRI back haul session betw een a VISM card and a call age nt, use the addse s command in the V oIP switchin g/trunki ng and switc hed AAL2 PVC oper ating modes.
5-43 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands adds es grp addsesgrp T o add a PRI ba ckhaul session group betwee n a VI SM card and a ca ll agen t, us e the addsesgrp command in the V oIP switchi ng/trunk ing and s witched AAL 2 PVC operati ng modes.
5-44 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addses set addsesset T o add a PRI back haul session se t between a VISM card an d a cal l agent, us e the addsesset comma nd in the V oIP switchin g/trunk ing and swit ched AAL 2 PVC operating mo des.
5-45 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addto neplan addtonepla n T o add a provisio nal tone plan to the curre nt VISM card, use the addtoneplan command in the V oIP switching /trunk i ng an d s w itc hed AAL2 PV C opera ting mo des.
5-46 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addtonep lan There i s n o r estric tion on t he file name o r extension of your t one plan d efiniti on file, but it must no t exc eed the maximum input size of the CLI co mmand.
5-47 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addto neplan Note If you do not spe cify the am pl itude s o f DT M F or MF R1 tone s, t he d efau lt value of 1 6384 (–9 d Bm) is ap pl ied.
5-48 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands addxgcpp ersiste vt addxgcppe rsistevt T o a dd pers istent xGCP.
5-49 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands addxgcpp ersistevt Relat ed Comma nds Comma nd De scripti on cnfcas flashtim e Configure s the m inimu m an d max imum CAS on- hook time pe riod s for inco ming flas h hooks on a specified end point.
5-50 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cc cc T o navigat e from th e curren t (logg ed on) c ard to ano.
5-51 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands chkfl ash chkflash T o verify the inte grity of a VISM ca rd’ s flash memory , use the chkflash command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-52 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clralm clralm T o c lea r ala rm s on a spe ci fic VI SM ca rd l ine , us e th e clr al m command in the V oI P switching /trunki ng, switched AAL 2 PVC, and AAL 2 trunking opera ting modes.
5-53 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clralm cnt clralmcnt T o cle ar the alarm c ounters and st atisti c.
5-54 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clralmcn ts clralmcnt s T o clear all the alarm counters and sta tistics on a VISM card , use the clralmcnt s com mand in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-55 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clral ms clralms T o clear alarm s on a VISM card, use the clralms command in the V oIP switching /trunk ing, switched AAL2 PVC, an d AAL2 trunk ing operat ing modes.
5-56 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clrcacf ailcntrs clrcacfailcntrs T o reset all con nection ad mi.
5-57 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clrmng cidcnt clrmngcidcnt T o clear AAL2 channel iden tif ier (CID) co unters, use the clrmngcidcnt command in the switc hed AAL2 PVC and AA L2 tru nking op er ating m odes.
5-58 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clrrtpcn t clrrtpcnt T o clear th e Real-T ime T ransport Pro to.
5-59 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clrrtp cnt dsprtpcons Displays the configu ratio n data o f al l sta tic R TP V oIP tru nking conn ec tions. dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session.
5-60 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clrsarc nt clrsarcnt T o clear th e se gmenta tion and r easse m.
5-61 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clrsarc nts clrsarcnt s T o c lear all segmenta tion an d rea ssemb.
5-62 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clrsarms gcnt clrsarmsgcnt T o c le ar th e c ontr ol messag e c.
5-63 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clrs crn clrscrn T o clea r t he co ntro l te rmi nal scre en, u se the clrscr n command in the V oIP switching/trunking , switched AAL2 PVC, an d AAL2 trunk ing operat ing modes.
5-64 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands clrslipcn t clrslipcnt T o c le ar c urre nt c loc k sli p c oun.
5-65 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands clrtaski nfo clrtas kinfo T o re set the values displaye d by the dsptaskinf o command , use the clrtaskinfo co mmand in the V oIP switching /trunki ng, switched AAL2 PVC, and AAL2 tr unking opera ting mo des.
5-66 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfaal2s ubcellm uxing cnfaal2 subcellmuxing T o enable or disab le AAL2 subcell mu ltiple xing , use the cnfaal2subcellmuxing command in the AAL2 trunking op erat ing mode .
5-67 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfaal2 timerp arams cnfaal2timerparams T o configur e the holdov e.
5-68 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfaal2tr anspa rams cnfaal2t ransparams T o co nfigure the tran.
5-69 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfad apgain cnfadapgai n T o enable or dis able t he DSP ad apti ve ga in featur e, us e the c nfadapgain command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-70 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfa lm cnfalm T o conf igure the alarm pa rame ters for a spec if ied line, use the cnfalm co mmand in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-71 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfalm Relat ed Comma nds C omma nd D escr iption clralm Clear s alarms fro m a spec ific line of a VISM car d clralms Clea rs al l ala rm s fr om a V I SM ca rd .
5-72 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfalmcn t cnfalmcnt T o configur e the collection of T ime Di v.
5-73 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfalm cnt Command Mode s V oI P swi tchin g/trun king, swi tched AA L2 PV C, a nd A AL2 trun king Usage Guid elines V alues higher than 2,147 ,483,6 47 for the ar gument v alues ar e truncat ed.
5-74 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfalmcn t • CRC code violation s encountered by the interface. • CRC code violations in the last 15 minutes encountered by the interf ace.
5-75 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfa nnag etim e cnfannaget ime T o c on figure th e tim e t ha t a.
5-76 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfannag etime dspanncache Displa ys all av ailable t emporar y announ cement file names, and as sociated age times be fore being refresh ed from the announ cement file server .
5-77 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfann dn cnfanndn T o desig nate th e annou ncem ent file server do main na me, use the cnfanndn command in the V oIP swi tchin g operat ing mode.
5-78 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfanndn dspannagetime Displa ys the time that a nonper mane nt announ cem ent is to remai n valid after it is p laced into the VI SM annou ncement c ache.
5-79 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfannp athpre fix cnfannpath prefix T o designate the main p ref i.
5-80 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfannpa thprefi x • g72 9_a/ • g7231_hi gh_rat e/ • g7231_ a_high_ rate/ • g7231_low_rat e/ • g7231_ a_low_rate/ Note VISM supports G.
5-81 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfannp athpre fix delannpermanent Deletes a perm anent an noun cement f ile and its as sociat ed codec type fro m the announ cement file server .
5-82 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfannpr efcode c cnfannpre fcodec T o conf ig ure the codec ty .
5-83 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfa nnpref codec cnfannreqt imeout Configures the expir ati on tim e f or annou nc em en ts t o begin p lay in g af ter t he VISM recei ves the anno uncemen t signal (requ est) from the ca ll agent.
5-84 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfannre qtimeout cnfannreq timeout T o conf igure the expir ati.
5-85 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfa nnre qtim eou t dspanncache Displays al l av ailable tem porar y announ cement file nam es, and associat ed age times be fore being refresh ed from the announ cement file server .
5-86 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcac cnfcac T o ena ble or di sable th e connec tion ad missio.
5-87 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfca cpa ram s cnfcacparams T o conf igure connectio n admissi on .
5-88 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcale a cnfcalea T o enab le or di sabl e the C ommun icat ion.
5-89 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc ascode cnfcascode T o conf igure channel as soc i at ed sig n .
5-90 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasc ode Command Mode s AAL2 trunking Usage Guid elines Y ou mus t add th e lin e assoc iated wit h the en dpt- num argument value be fore you use t his com mand.
5-91 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcasdialdelay cnfcasdialde lay T o c onfigure the VISM wait time .
5-92 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasd ialde lay Relat ed Comma nds C omman d Descr iption dspcastimers Displa ys an endpoi nt’ s cur rently co nfigured CAS timer s.
5-93 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfca sendpt cnfcasendpt T o associat e an endpoint with a channel associ ated signaling (CAS) va riant name, use the cnfcasendpt comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-94 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasf lash time cnfcasflashtime T o c onfigure th e minim um a.
5-95 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcasflashtime Relat ed Comma nds C omma nd De scripti on addxgcppersistevt Adds persistent xGCP e vents. cnfcas glareattr ib Config ures the direction of CAS calls and the glare polic y for a specif ied endpoin t.
5-96 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasg lareat trib cnfcasglareattrib T o c onfigure the di rect.
5-97 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcasglareattrib Exam ples The follow ing e xample sho ws that end.
5-98 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasg laret ime cnfcasglaretime T o co nfigure the c hannel as.
5-99 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcas glareti m e Exam ples The followin g example sho ws that end.
5-100 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasg uardtim e cnfcasguardtime T o conf igure the channel as.
5-101 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcasg uardti me Exam ples Th e fol lowing exampl e shows that en.
5-102 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcaso ffhookt ime cnfcasoffhoo ktime T o c onfigure a m inimu.
5-103 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc asonhookti m e cnfcasonhoo ktime T o c onfigure a mi nimum pr.
5-104 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcaso nhookt ime Relat ed Comma nds C omman d Descr iption dspcastimers Displa ys an endpoi nt’ s cur rently co nfigured CAS timer s.
5-105 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc aspackage cnfcaspacka ge T o c on figure th e Medi a G at ewa.
5-106 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasp ackage in-pack age P ackag e na me t o be used for pe rsist ent events obse rved on an i nc omi ng telephon y call.
5-107 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc aspackage Command Mode s V oI P swi tchin g/trun king, swi tched AA L2 PV C, a nd A AL2 trun king Usage Guid elines T his comm and enab les RFC 3064 suppo rt.
5-108 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasp ackage Command Description addxgcppersistevt Adds persistent xGCP e vents.
5-109 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcasp aramsour ce cnfcaspara msource T o c on figure c hann el a.
5-110 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasp aramso urce Relat ed Comma nds C omman d Des cription ds pca spa ra ms ource D isplays an endpoint ’ s cur rently co nfigured CAS-rela ted timer sour ce.
5-111 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcas var cnfcasvar T o c onfigure a p reviously ad ded ch anne l.
5-112 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasw inktim e cnfcaswinktime T o conf igure the channel asso.
5-113 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcas winkti me T o use this com mand, you mus t ensure t hat the e ndpoint i ndicate d by the en dpt-num argument value ha s been previously a dded, and tha t the associate d DS0 is co nfigured for CA S.
5-114 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcasx gcp cnfcasxgcp T o conf igure ch annel asso ciated si g.
5-115 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfclksrc cnfclksrc T o con figure the PXM1 , PXM1E, PX M45, VISM .
5-116 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfc lks rc • If the cl ock sour ce i s the PXM ’ s int erna l c rys tal a nd no o th er c loc k source h as be en sp ec ified, d o not conf igure the cl ock source.
5-117 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfco4timer cnfco4t imer T o configur e the bearer continuit y test CO4 timer value , u se the cnfc o4ti mer command in the V oIP switching /trunk ing an d swi tched A AL2 PVC opera ting mo de s.
5-118 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcodec jtrdela y cnfcodecjtrdel ay T o configur e the jitter .
5-119 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcod ecjtrde lay Exam ples The follo wing e xample sho ws th at codec G.
5-120 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcodec neg cnfcodecne g T o configur e th e prio rit y order of the lists of codec list pr ior ity order , use the cnf codecneg command in the V oIP switching/trunking operating mode.
5-121 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcod ecparams cnfcodecpa rams T o configure codec parame ter s.
5-122 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcodec params Command Mode s V oIP switching Usage Guid elines The packetiza tion period paramet er is required b u t the remaining para meters are opti onal.
5-123 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcod ectmpl cnfcodectmpl T o assign a code c template to an entir e VISM card, use th e cnfcodectmpl comma nd in the V o IP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-124 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcodec tmpl Relat ed Comma nds C omman d Descr iption dspcodectmpls Display s all ent ries in the V ISM card’ s codec tem plate table .
5-125 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc ompv ad cnfcompvad T o enable or dis abl e voi ce acti vity d.
5-126 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfcon cnfcon T o co nfigur e a con nec ti on bet wee n a VISM .
5-127 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfcon Usage Guid elines Follow standa rd CL I pro ced ure s w hen using t his co mma nd.
5-128 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfconca c cnfconcac T o c onfigure c onnec tion ad mission contro l (C A C) on a pr eviously ad ded con necti on, u se the cnfconcac comm an d in t he A AL2 t runki n g o pera tin g m od e.
5-129 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc onca cpa ram s cnfconcacp arams T o conf igure connec tion ad.
5-130 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfconca cpol cnfconcacp ol T o conf igure the polici es for f .
5-131 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfc onprot ect cnfconpro tect T o conf igure protect ion on a PVC, use the cnfconpr otect command in t he V oIP switching/tr unking operati ng mode.
5-132 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfconv bdpol cnfconvbdpo l T o conf igure the polici es for f .
5-133 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfconv cci cnfconvcci T o associate a virtual circuit co nnection iden tif ier (VCCI) a nd a remote address with an LCN, u se the cnfc on vcci in the switched AAL2 PVC operating mode.
5-134 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfdeftos cnfdeftos T o conf igure the type of service (T oS) parameters for both co ntrol and bearer IP packets, use the cnfd ef to s c ommand i n the V oIP switching /trunk ing operat ing mode .
5-135 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfdisctimers cnfdisctimers T o specify the wait delay times for t.
5-136 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfdn cnfdn T o conf igure the resolution type of a specif ied domain name, use the cnfdn command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-137 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfdn dspdnips Displays all statistica lly prov isioned and exte rnally resolv ed IP addresses conf igured for a sp eci fied dom ain na me.
5-138 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfdnss rvr cnfdnssrvr T o de sign ate a dom ain name a s a dom ain name se rver (DNS) , use the cnfdnssrvr command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-139 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfdp vcoampara ms cnfdpvcoamparams T o config ure the tra nsmitte.
5-140 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfds0 gain cnfds0gain T o configur e the adjustable gain for a specifie d DS0, use the cnfds 0gain command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-141 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfds0lo calcas cnfds0localc as T o conf igure a l ocal channe l a.
5-142 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfds0 localcas Relat ed Comma nds C omman d Des cription dspds0localcasstatus Display s the cur rently co nfig ured local CAS status for a li ne and D S0.
5-143 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfds0loop cnfds0loop T o conf igure a loopback type for a specif ied line and DS0, us e the cnfds 0loop comman d in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-144 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfds0 music thresh old cnfds0musicthres hold T o c onfigure th.
5-145 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfe cane nab le cnfecanena ble T o enable or disa ble echo ca ncella tion on a line, us e the cnfecanenable co mmand in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-146 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfecanr ec cnfecanre c T o c onfigure resi dual ech o con trol.
5-147 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfec ant ail cnfecantail T o c onfigure th e max imum tail len gt.
5-148 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfendpt caden ce cnfendptca dence T o confi gure c adence (digit tone) tim es for an e ndpoint, u se th e cnfendptcadence command i n the V oIP switching /trunk i ng an d A AL 2 tr unkin g o pera ting m od es.
5-149 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnferl cnferl T o conf igure a digita l signal proc essor (DSP) retu rn echo loss v alue, us e the cnferl command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-150 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfgain cnfgain T o conf igure the adjusta ble ga in for a VISM card, use the cnfgain command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-151 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfgwis cnfgwis T o conf igure an out-of-s ervi ce VISM ca rd to th e in- s er v ice s tat e, use the cnfgw is command in the V oIP switching /trunki ng operati ng mode.
5-152 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfg wo os cnfgwoos T o conf igure an in-s ervice VISM c ard to the out-of-servic e state, use the cnfgwoo s co mma nd in th e V o IP switching /trunk ing an d swi tched A AL2 PVC opera ting mo de s.
5-153 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfjtrinitdelay cnfjtrinitdelay T o configur e the initial jitter b uffer delay size, use the cnfjtrinitdel ay comman d in the V oIP switching /trunki ng, switched AAL2 PVC, and AAL2 tr unking opera ting mo de.
5-154 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfjt rinitde lay Exam ples The following e xample sho ws that the jitter b uffer size is set to 70 millisecond s: cnfjtrinitdelay 70 Relat ed Comma nds 1.
5-155 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfjtrmode cnfjtrmode T o conf igure the jitter alg orithm with a .
5-156 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflapd retrans cnflapdre trans T o c onfigure a maximu m numb .
5-157 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflapd timer cnflapdtime r T o c onfigure two LAPD timers fo r a previousl y added L ink Acce ss Protoc ol D c hannel (LAPD) , use the cnflapdtimer command in the V oIP switching /trunk ing operating mod e.
5-158 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflapd timer cnflapdtype Configures t he various type s o f LA PD st ack s for a pr eviously ad ded LA PD.
5-159 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflapdtrunkpvc cnflapdtru nkpvc T o a ssign the p erma nent virtu.
5-160 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflapd trunkp vc dsprtpcon Displays the con figurat ion data of a specif ie d static R TP V oIP trunking connec tion.
5-161 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflapdtype cnflapdtype T o c onfigure the various ty pes of L ink.
5-162 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflapd type Relat ed Comma nds C omman d Des cription cnflapdre trans Configu res a ma ximum nu mber of fra me ret ransmi ssions for a previous ly added LAPD .
5-163 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflapdwinsize cnflapdwin size T o con figure a maximu m number of out standing (unacknowledge d) I-fram es, use the c n fl a pdw in s i ze comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-164 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfln cnfln T o conf igure ch aracteri stics fo r a VISM card line, use the cnfln comman d in t he V o IP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-165 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfln Command Mode s V oI P swi tchin g/trun king, swi tched AA L2.
5-166 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflndigi torder cnflndigitorder T o assign the order in which .
5-167 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflngain cnflngain T o conf igure the a djusta ble gain for all D.
5-168 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflnis cnflnis T o conf igure an out-of-s ervice VISM card line to the in-ser vice state , use the cnfl nis comman d in t he V oIP switchin g/trunki ng operating mo de.
5-169 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflnmusicthreshold cnflnmusicthres hold T o c onfigure the mu sic.
5-170 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflnoo s cnflnoos T o conf igure a n in-servic e VISM card line to the o ut-of -service state, us e the cnflnoos command in the V oIP switchin g/trunki ng operating mo de.
5-171 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfl nring bac k cnflnringback T o c on figure t he ri ng back ton.
5-172 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflnringb ack dsplntonetimeout Displays the conf igured timeout periods for all call progress tones of a specif ied VISM card line .
5-173 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflnsig cnflnsig T o co nfigure the signalin g mode for a VISM ca rd line , use the cnflnsig comma nd in the AAL2 trunki ng operati ng mode.
5-174 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflntone plan cnflntonepla n T o assign a built- in or provisi.
5-175 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflnto neplan dsptoneplans Displa ys the ton e configurati on of all tone pl ans—eit her prec onfigured (built-in) or user-added t one plans .
5-176 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflntone timeou t cnflntonetimeout T o m odify th e tim eout p.
5-177 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflntonetimeout Exam ples Th e fol lowing example sh ows that the.
5-178 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnflntrunk cond cnflntrunkcond T o enab le or di sable line con.
5-179 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflntrunkcond dsplapd Displa ys data about an LAPD. dsplapdtrunkpvc Displa ys the assigned PVC tru nk type that ca rries LAPD trunk messages for the cu rrent VISM card.
5-180 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfmgcgrp entry cnfmgcgrpentry T o modify t he call agent pr io.
5-181 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfmgcgr ppar am cnfmgcgrpparam T o mod ify a cal l agent red unda.
5-182 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfmgcgrp param dspmgcgrps Displ ays all co nfigured call age nt redun dancy groups. dspsr cppeer grp params Displays t he SRCP paramet ers for all call agent redun dancy groups that have SRCP added.
5-183 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfmgcgr pproto col cnfmgcgrpprotoco l T o c onfigure a c all agen.
5-184 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfmgcgrp protoc ol Command Mode s V oIP swi tch ing/ tru nking.
5-185 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfmidcalltimers cnfmidcalltimers T o conf igure the midcal l dual.
5-186 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfmus icthre shold cnfmusicthreshold T o conf igure the music .
5-187 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfnwcot cnfnwcot T o conf igure VISM for a g ateway-in itiated network c ontinuity t est, use the cnfnwcot com ma nd i n th e V oIP switchin g/trunking a nd switc hed AAL2 PVC op erating modes.
5-188 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfpncon cnfpncon T o set priorit y routing f or a specif ied c.
5-189 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfprofelemvbd cnfprofelemvbd T o confi gure the voice band data (VBD) prof ile eleme nt for a profile , use the cnfprofe lemv b d comman d in the swi tched A AL2 PVC o perating mo de.
5-190 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfp rof ele mvbd Command Mode s Switch ed AAL2 PVC Usage Guid elines Use the dspaal2prof ile comman d to ide ntify valid combina tions o f codec type, p acketiza tion p eriod, and silence inser tion descriptor .
5-191 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnf prof elem voi ce cnfprofelemvoice T o conf igur e the prof ile v oice e lemen t, use th e cn fprof elemvo ice command in the switched AAL2 PVC operati ng mode.
5-192 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfp rof ele mvoic e Command Mode s Switch ed AAL2 PVC Usage Guid elines Use the dspaal2prof ile comman d to ide ntify valid combin ations o f code c type, p acketi zation p eriod, and SID.
5-193 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfprofneg cnfprofneg T o conf igure the profi le list p riority order , use the cnfpr ofneg command in the switc hed AAL2 PVC operati ng mode.
5-194 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfprof params cnfprofparams T o conf igure a prof ile prefer ence, u se the cnfprofparams command in the switched AAL2 PVC and AAL2 trun king operati ng modes.
5-195 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfrsvp cnfrsvp T o conf igure Resource R eserv ation Protoc ol (R.
5-196 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfrsvpref reshmi ss cnfrsvpref reshmiss T o con f igure the nu.
5-197 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfrtcprepint cnfrtcprepint T o c on figure th e Real T ime Contr .
5-198 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfrtpc on cnfrtpcon T o modi fy an e xist ing s tatic Real- T ime T ransp ort Pr otoc ol (R TP) V oIP trun king co nnec tion, use th e cnfr tpc on command in th e V oI P switch ing/trun king operat ing mode.
5-199 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfrtpc on Command Mode s V oIP switching/trunking Usage Guid elines Th e G.723. 1 codecs are supp orted for VISM-PR cards an d are not supp orted for VISM card s.
5-200 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfrtpc on Exam ples Th e following exampl e shows that the R TP trunki ng connec tion 26 is configured (modified) wi th G.
5-201 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfrtprxtimer cnfrtprxtimer To enab le or disable the r e ce i pt .
5-202 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfrudpt runkrmt ip cnfrudptrunk rmtip T o modi fy t he remote .
5-203 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfrud ptrunk rmtip dsprudptrunk Displays the con figuration data of a spe cified ISDN PRI ba ckhaul R UDP session. dsprudptrunks Displays the configura tion d ata o f all IS DN PRI ba ck haul RUDP session s.
5-204 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsesack cnfsesack T o con figure the tim eout peri od before .
5-205 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfs esm axres et cnfsesmaxreset T o conf igur e the maxi mum numb.
5-206 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsesm axseg cnfsesmaxseg T o co nfigure the ma ximum segme nt.
5-207 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfsesm axwindow cnfsesmaxwindow T o c on figure th e ma ximu m nu.
5-208 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsesnul lsegtmo ut cnfsesnullseg tmout T o configur e the tim.
5-209 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfseso utofseq cnfsesoutofseq T o c onfigure the maximu m numb er.
5-210 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsespor t cnfsesport T o c onfigure th e por t numbe rs of a previously ad ded PR I backh aul sessi on, use the cnfs es p ort comman d in the V oIP switchi ng/trunk ing opera ting mo de.
5-211 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfsesr etrans cnfsesretrans T o conf igure the timeou t perio d for un ackno wledg ed pack ets and num ber of re transmis sions, use th e cnfs esr etr ans command in the V oI P switchin g/trun king oper ating mo de.
5-212 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfses statetm out cnfsesstatetmout T o configur e the number o.
5-213 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfsessyncatm ps cnfsessyncatmps T o con figure the ma ximum num ber of atte mpts to sync hroniz e with the call agen t, use the cnfsessyncatmps c ommand in the V oIP switc hing/tr unking opera ting mode.
5-214 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsrcp peer cnfsrcppee r T o con figure the port for the call .
5-215 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnf src ppeer grp para m cnfsrcppee rgrpparam T o modi fy the S im.
5-216 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfsrcp peergrp param dspmgcgrps Displ ays all co nfigured call age nt redun dancy groups. dspsr cppeer grp params Displays t he SRCP paramet ers for all call agent redun dancy groups that have SRCP added.
5-217 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfsrc pretry cnfsrc pretry T o c on figure th e VISM car d level .
5-218 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnft 38fx lco cnft38fxlco T o config ure the fax h andling instructio ns for a specif ie d line, use the cnft38fxl co command in the V oIP switching /trunki ng operati ng mode.
5-219 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnft38fx lco Relat ed Comma nds C omma nd De scripti on cnfcodectmpl As signs a code c template to an entire VISM card .
5-220 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnft38 nsetime out cnft38nsetimeout T o config ure a sp ecif ie.
5-221 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnft38p arams cnft38params T o conf igu re the T .38 fa x tran sfer paramet ers f or a s pecif ied l ine, use th e cnft38param s command in t he V oIP switchin g/trunki ng operating mo de.
5-222 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnft38 params Command Mode s V oI P swi tchin g/t runking Usage Guid elines Follo w standard CLI proced ures for this comman d.
5-223 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnft38p arams cnft38params 2 3 28 20 3 0 2 1 1 500 4000 Relat ed Comma nds C omma nd De scripti on cnfcodectmpl As signs a code c template to an entire VISM card .
5-224 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnftftpdn cnftftpdn T o select t he T ri vial Fil e T ransfer Protoco l (TFTP) domain na me, use the cnf tftpdn command in the V oIP switchin g/trunki ng and switc hed AAL2 PVC oper ating modes.
5-225 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnflntrunkcond cnflntrunkcond T o enable or disable t r unk cond i.
5-226 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfvbdc odec cnfvbdcodec T o conf igure v oiceban d dat a (VBD) upspe ed codec on th e curr ent VI SM card, u se th e cnfvbdcodec comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-227 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfvbd pol cnfvbdpol T o co nfigure VISM card level voiceband dat .
5-228 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfv ism dn cnfvismdn T o c on figure th e cu rr ent V ISM c ard dom ai n name , use th e cnfvismdn command in the V oIP switching /trunk ing an d swi tched A AL2 PVC opera ting mo de s.
5-229 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfvismip cnfvismip T o con figure the cu rrent V ISM card co ntro.
5-230 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfv ism mod e cnfvismmode T o conf igure the initial oper ating mode for a VISM card, use the cnfvismmode command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-231 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfv oipt im erpa ram cnfvoiptimerparam T o configur e the holdov .
5-232 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfvoiptr anspa rams cnfvoiptran sparams T o configure the V o .
5-233 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfvoip transp arams Relat ed Comma nds C omma nd Descript ion cnfvoipt imerparam Configures the ho ldover time for V AD be fore sil ence c ompressi on is act i vated.
5-234 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfxgcpb t cnfxgcpbt T o co nfigure a defa ult beare r type— .
5-235 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfxgc pinteropsdp ost cnfxgcpinte ropsdpos t T o enable or disabl.
5-236 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfxgcpm wd cnfxgcpmwd T o configur e the maximum waiting delay.
5-237 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands cnfxgc ppeer cnfxgcppee r T o configur e the User Datagram Protoco.
5-238 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands cnfxgcpr etry cnfxgc pretry T o con figure VISM minim um and ma.
5-239 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delann alldynami c delannalldyn amic T o delete all an nounc emen .
5-240 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delannal ldyn amic dspannpathpref ix Di splays the main prefix direct ory path from which V ISM retrieves announ ceme nt files from th e annou ncemen t file server .
5-241 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dela nndynami c delanndynamic T o delete an anno uncemen t f ile a.
5-242 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delanndy namic Relat ed Comma nds C omman d Description addannpermanent Configure s an announ cem ent server file and assoc iated codec typ e as perman ent.
5-243 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dela nnp erma nen t delannperman ent T o delete a perma nent annou.
5-244 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delannpe rmanent dspanncontrols Disp lays a summary list of all prov isionable announc ement file v ariables, including v ariables assoc iated with all announ cement f ile CLI commands.
5-245 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delcas var delcasvar T o delete a chan nel asso ciated s ignali ng (CAS) v ariant, use th e del ca sva r comman d in the V o IP switching /trunki ng operati ng mode.
5-246 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delccs delccs T o delete the association betwe en a common chan.
5-247 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delcid delcid T o d ele te th e a ssoci ati on be t wee n an e ndp oint an d a n LC N/CI D pa ir, use the delcid command in the AAL2 trun king operati ng mode.
5-248 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delcon delcon T o delete a PVC be tween a VISM car d and an MGX 8000 Series shelf PXM car d, use the delcon comm and in the V oIP swit ching/tr unking, sw itched A AL2 PVC, and AA L2 trunkin g operatin g modes.
5-249 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delco nl oop delconloop T o de lete a loc al loopba ck stat e on a connec tion to the cell bus, use the delc onloop comm and in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-250 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands deldn deldn T o delete a domain name , use the deldn command in the V oIP sw itching/ trunking an d switche d AAL2 PVC operatin g mode s.
5-251 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands deldn ip deldnip T o de lete a st atisti cally provisi oned IP ad dress of a dom ain name, use the deldnip command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-252 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delendpt delendpt T o delete a sp ecif ied e ndpoint on a VISM car d line, use the dele ndpt command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-253 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delend ptloop delendptloo p T o take an endpoin t out of the loopback condition, use the delendptloop comm an d i n the V o IP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-254 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delendpt s delendpts T o d ele t e a rang e of conse c utive endpo int s on a V I SM ca rd , use t he delendpts command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-255 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delend pts Command Mode s V oI P swi tchin g/trun king, swi tched .
5-256 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dellapd dellapd T o dele te an Link A ccess Protocol D channel (LAPD) , use the dellapd command in the V oIP switching /trunki ng operati ng mode.
5-257 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dellapd trunk dellapdtru nk T o d elet e a Li nk Acc ess Prot ocol D c hann el (LAP D) co nfigured line, u se t he dellapdtrunk command in the V oIP switching/trunking operating mode .
5-258 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dellapd trunk dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session. dsprudptrunks Displays the configura tio n data o f all IS DN PRI ba ck haul RUDP session s.
5-259 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delln delln T o de le te a D S1 li ne on a VI SM card , us e the delln command in the V oIP switc hing/tru nking, swit c hed AAL2 PVC, an d AAL2 trunk ing opera ting modes .
5-260 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dellnloop dellnloop T o delete th e T1 o r E1 lo cal line loopback state f or a VISM card, use the dellnloop command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-261 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dellnto neplan dellntonepla n T o delete a built- in or pro vision.
5-262 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delmgc delmgc T o delete a cal l agen t from a VISM car d’ s list of conf igured cal l agents , use th e delmgc command i n th e V oIP switchin g/trunking a nd switc hed AAL2 PVC op erating modes.
5-263 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delmgcgr pentry delmgcgrpentry T o delete a call agen t from a call agent re dundanc y group, use t he delmgcgrpentry comm and in t he V oIP switching /trunk i ng an d s w itc hed AAL2 PV C opera ting mo des.
5-264 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delmgcgrp protoc ol delmgcgrpprotoco l T o d elete a Media Gate.
5-265 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delmgcgr pproto col cnfsr cppeer grpp aram Mo difies t h e SRC P he ar tb eat in te rval an d m ax imum U D P s iz e fo r a specified call a gent redun dancy gr oup .
5-266 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delport delport T o delete th e VISM po rt on th e pack et netw ork side , use th e delport command in th e V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-267 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delrscprtn delrscprt n T o delete a resource partition w hich w as.
5-268 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delrtpc on delrtpcon T o dele te a static Real-Time T ra nsport Prot ocol (R T P) V oIP trunki ng connec tion, use the delrtpcon comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-269 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delrtpc on dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session. dsprudptrunks Displays the configura tion d ata o f all IS DN PRI ba ck haul RUDP session s.
5-270 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delrudpt runk delrudptrunk T o d ele te an I SDN PRI ba ck haul.
5-271 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delru dpt runk dsprtpcons Displays the configu ratio n data o f al l sta tic R TP V oIP tru nking conn ec tions. dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session.
5-272 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delses delses T o de lete a PRI back haul sessio n, us e the delses command in the V oIP switching /tr unki ng and sw itch ed AAL2 PVC o pera ting m ode.
5-273 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delsesg rp delsesgrp T o d elete a PRI bac khaul session g roup, use the delsesgrp comma nd in the V oI P swit ching/tru nking and swi tched A AL2 P VC operat ing mode.
5-274 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delses set delsesset T o d elet e a PRI ba ckha ul sessio n se t, use th e delsesse t command in the V oIP switching/trunk ing and swi tched A AL2 P VC operat ing mode.
5-275 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands deltoneplan deltoneplan T o delete a prov isional tone plan fr om the system , use th e del toneplan com mand in th e V oIP switching /trunk i ng an d s w itc hed AAL2 PV C opera ting mo des.
5-276 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands deltone plan dsptoneplan Displ ays the ton e configurati on of a speci fied tone plan—ei ther a prec onfigured ( built-in ) o r user-adde d to ne pla n.
5-277 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands delxg cpcon delxgcpcon T o delete an xGCP connection specifie d by the xGCP con nection identif ication number , use the delxgcpc on comman d in the V oIP switchi ng/trunk ing and swit ched AAL2 PVC operating mod e.
5-278 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands delxgcpp ersist evt delxgcppersiste vt T o delete a persistent xGCP e ve nt, use the delxgcppersiste vt command in the V oIP switching/tr unking and switc hed AAL2 PVC op erating mo des.
5-279 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dnco n dncon T o configur e a specifie d connection do wn, prev en.
5-280 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspaal2pa rams dspaal2 params T o displ ay AAL 2 conf igurati on para meters, use t he dspaal2params c omman d in the s witc hed A AL 2 PVC and AA L2 tru nking op er ating m odes.
5-281 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspaal2profile dspaal2 profile T o display data about a specif ied AAL2 profile ty pe and prof ile number , use the dspaal2prof ile comm an d in t he A AL2 t runki n g o pera tin g m od e.
5-282 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspalm dspalm T o display th e alarms asso ciated with a specif ied line, u se the dspalm command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-283 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspalmcnf dspalmcnf T o display the threshold data about the a lar.
5-284 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspalmc nf Relat ed Comma nds C omman d De scri ption cnfalmcnt Conf igures the collec tion of TDM line statistics.
5-285 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspalmcnt dspalmcnt T o displa y alarm counter s and s tatisti cs,.
5-286 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspalmc nt RcvOOFCount: 1 RcvRAICount: 0 RcvFECount: 97997379 Relat ed Comma nds C omman d De scri ption clralmcnt Cle ars the alarm counters and stati stics on a spec ifie d VISM card line.
5-287 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspal ms dspalms T o display the alarms for a specif ied VISM card line type, use the dspalms comma nd in th e V o IP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-288 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspanna getime dspann agetime T o display the time that a nonpe.
5-289 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspan nageti me dspannpathpref ix Di splays the main prefix direct ory path from which V ISM retrieves announ ceme nt files from th e annou ncemen t file server .
5-290 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannc ache dspann cache T o display all a vaila ble tempor ar.
5-291 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspa nnc ach e dspanncontrols Disp lays a summary list of all prov isionable announc ement file v ariables, including v ariables assoc iated with all announ cement f ile CLI commands.
5-292 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannc ontrols dspanncontrols T o di splay a summ ary list of .
5-293 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspan ncontr ols dspannagetime Displa ys the tim e that a nonperma nent a nnouncem ent is to remai n valid after it is plac ed into the VISM announ cement cac he.
5-294 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannd n dspann dn T o display the announcem ent file ser ver domain na me, use the dspanndn comma nd in the V oIP swi tchin g operat ing mode.
5-295 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspanndn dspannpathpref ix Di splays the main prefix direct ory path from which V ISM retrieves announ ceme nt files from th e annou ncemen t file server .
5-296 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannp athpre fix dspann pathprefix T o display the main pref .
5-297 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspannpat hprefi x dspanndn Displa ys the anno uncement file server domain name.
5-298 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannp ermanent s dspannperman ents T o di splay al l av ailab.
5-299 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspan npermane nts dspanncontrols Disp lays a summary list of all prov isionable announc ement file v ariables, including v ariables assoc iated with all announ cement f ile CLI commands.
5-300 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannp refcod ec dspann prefcodec T o d isplay the cod ec ty p.
5-301 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspannpre fcodec dspanncontrols Disp lays a summary list of all prov isionable announc ement file v ariables, including v ariables assoc iated with all announ cement f ile CLI commands.
5-302 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspannre qtime out dspann reqtimeout T o d i splay the expirati.
5-303 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspan nreqt imeout dspanncontrols Disp lays a summary list of all prov isionable announc ement file v ariables, including v ariables assoc iated with all announ cement f ile CLI commands.
5-304 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcacf ailcntrs dspcac failcntrs T o display the connection ad.
5-305 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspca lea dspcale a T o displa y the C ommuni cations Assi stance .
5-306 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcardd sp dspcarddsp T o display all card l ev e l con figu r.
5-307 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspca sendpts dspcase ndpts T o d ispl ay da ta abou t c onfigured cha nne l assoc ia ted signa ling (CA S) endpo in ts, use t he dspcasendpts comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-308 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas glareatt rib dspcasglareattrib T o di spl ay the dir ect.
5-309 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcasgl areattri b Relat ed Comma nds C omma nd De scripti on addxgcppersistevt Adds persistent xGCP e vents.
5-310 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas package dspcasp ackage T o d ispl ay t he Me dia G atewa.
5-311 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspc aspackage Relat ed Comma nds C omma nd De scripti on addxgcppersistevt Adds persistent xGCP e vents.
5-312 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas paramso urce dspcasp aramsource T o di spl ay th e cur r.
5-313 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspca stimers dspcastimers T o displa y the cu r re ntly con f igu.
5-314 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas timers Relat ed Comma nds C omman d Des cription addxgcppersistevt Adds persistent xGCP e vents.
5-315 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcasvar dspcasvar T o d ispl ay d ata a bout cha nne l assoc iat ed si gnal ing (CAS ) variant s f or a given variant na me, use th e dspcasvar command in the V oIP switching/tr unking operating mo de.
5-316 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas varend pts dspcasva rendpts T o display all en dpoints a.
5-317 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcasv ars dspcasva rs T o display the paramete rs of all ch anne.
5-318 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcas xgcps dspcasx gcps T o di splay timer paramet ers for th.
5-319 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspccs dspccs T o di spla y the configura tion dat a of a previous.
5-320 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspccs chans dspccsc hans T o display all ch annels that ar e c.
5-321 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspccs cnt dspccsc nt T o display th e common ch annel signaling (.
5-322 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcd dspcd T o d isplay the cu rren t VISM card ’ s configur.
5-323 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcds dspcds T o di splay a list o f ch assis card types, with as.
5-324 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcid dspcid T o display th e conf igur ation data of an AAL2 channe l identif ier (CID) on the cu rrent VISM card, use the dspcid command in the switche d AAL2 PVC and AA L2 trunk ing operat ing modes.
5-325 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcids dspcids T o display all AAL2 ch annel identif iers (CIDs) for an LCN on the curren t VISM card, use the dspcids comm an d in the switch ed A AL2 PVC an d AA L2 t runk in g ope ra ting mod es.
5-326 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspco4 timer dspco4t imer T o display the bearer continui ty test CO4 timer va lue, use the dspco4timer command in the V oIP switching /trunki ng operati ng mode.
5-327 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcodecj trdelays dspcodecjtrdela ys T o display the c onfi gured.
5-328 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcode cparams dspcodecpa rams T o displ ay code c paramete rs, use the dspcodecparams command i n the V oIP swit ching/trun king operati ng mode.
5-329 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcodect mpls dspcodectmpls T o display all entries in the codec tem plate table, u se the dspcodectmpls command i n the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-330 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcon dspcon T o di splay the c onfiguratio n data of a channe l, use the dspcon command in the V oIP switching/tr unking, switched AAL 2 PVC, and AAL 2 trunking opera ting modes.
5-331 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspcon ChanFarEndAddrType: notapplicable ChanFarEndE164Addr: 0 ChanFarEndGWIDAddr: .
5-332 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspconc ac dspcon cac T o di splay c onne ction ad mission cont.
5-333 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspconcnt dspcon cnt T o displ ay coun ter co nf igur ation data (.
5-334 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspcons dspcon s T o d ispl ay c ha nnel con figurati on data f.
5-335 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspconvbd pol dspcon vbdpol T o display fax/mo dem upspe ed, conn .
5-336 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspdisct imers dspdisctimers T o di splay the Resta rt in Progr.
5-337 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspdnallips dspdna llips T o display all statistically provisioned.
5-338 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspdnip s dspdnip s T o display all statistically pro v isioned.
5-339 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspdns dspdns T o di splay the con figuration da ta of all dom ain name s of a call agent , use the dspdns command in the V oIP swit chin g/trun king, swi tch ed AA L2 PVC, and AA L2 t runki ng oper ati ng mode s.
5-340 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspdns srvr dspdnssrvr T o dis play the domain nam e of the co .
5-341 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspdpv coampara ms dspdpvcoamparams T o display the transmitte d a.
5-342 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspds0 gain dspds0gai n T o display the adjustable gain v alues for a specifie d DS0, use the dspds0gain command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-343 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspds0localcasstatus dspds0localca sstatus T o display the c urren.
5-344 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspds0 loop dspds0loop T o d i splay the loopb ack t ype f or a spe c ified line an d DS0, u se the dspds0loop command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-345 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspds0musicthr eshold dspds0musicthresh old T o display th e music.
5-346 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspendp t dspend pt T o display configur ation da ta of a spe cified VISM c ard end point, use the dspendpt command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-347 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspen dpt Relat ed Comma nds C omma nd D escr iption addendpt Adds a n e ndpo int on a VI SM car d. delendpt Deletes a spec ifie d endpoint on a VISM card.
5-348 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspendp ts dspend pts T o d ispl ay c on figuratio n dat a a bo.
5-349 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspg ain dspgain T o display the adjustable gain fo r a specified VISM card, use the dspgain command in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-350 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspgwst ate dspgwstate T o display th e current us er -conf igured s ervice stat e of the gat ew ay , use the dspgwstate in the V oIP switching /trunki ng operati ng mode.
5-351 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl apd dsplapd T o display co nf igurati on data ab out a Link Access Pro tocol D channel ( LAPD), use th e dsplapd comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-352 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplapd cnflntrunkcond Enab les or dis able s li ne c ondit ioni ng on a V ISM ca rd l ine i f a netw ork a larm is encou ntered.
5-353 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl apd s dsplapd s T o displ ay conf igurati on data abou t all Li nk Acces s Prot ocol f or ISDN D ch anne ls (LAP Ds), us e the dsplapds command in the V oIP switching/trunkin g operating mode.
5-354 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplapd stat dsplapd stat T o d ispl ay c on figuration data a .
5-355 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplapdst at Relat ed Comma nds Ther e ar e no r ela te d comm an ds .
5-356 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplapd trunkp vc dsplapd trunkpvc T o d ispl ay t he assign ed.
5-357 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplap dtrunkpvc dsprudptrunk Displays the con figurat ion data of a specif ied ISDN PRI backhaul R UDP session. dsprudptrunks Displays the configura tion d ata o f all IS DN PRI ba ck haul RUDP session s.
5-358 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplapd trunks dsplapd trunks T o di splay the data of all Li nk Access Prot ocol D channe l (LAPD) configured trunk s, use the dsplapdtrunks command in the V oIP switching/trunkin g operating mode.
5-359 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplapd trunks dsprtpcon Displays the con figurat ion data of a specif ic static R TP V oIP trunking connec tion. dsprtpcons Displays the configu ratio n data o f al l sta tic R TP V oIP tru nking conn ec tions.
5-360 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplin ecasbit s dsplinecasbi ts T o display the currently tran.
5-361 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplinecasbits Relat ed Comma nds C omma nd D escr iption addendpt Adds a n e ndpo int on a VI SM car d. addendpts Adds a consec uti ve numbe r of endp oints to a VISM card.
5-362 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspln dspln T o display th e confi g uration data of a VISM card line, us e the dspln comman d in the V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-363 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplnc ids dsplnci ds T o display th e channe l identif ication (C.
5-364 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplndigi torder dsplndi gitorder T o di sp lay th e o rde r in.
5-365 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl ndsp dsplnds p T o display the digital signal processor (DSP).
5-366 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplndsx0 s dsplnds x0s T o di splay the con f igurat ion data .
5-367 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplnd sx0s Relat ed Comma nds C omma nd D escr iption addln Ad ds a T1 or E1 line to a VISM card . delln Deletes a T 1 or E1 line f rom a VISM card.
5-368 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplnen dptstat us dsplnendptst atus T o display th e status of.
5-369 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplng ain dsplngain T o display th e adjustable gain for all DS0s.
5-370 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplnmu sicthres hold dsplnmusicthresh old T o display th e mus.
5-371 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl nring bac k dsplnringback T o display the ringback tone me th.
5-372 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplnringb ack dsptoneplans Displ ays the ton e configurati on of all tone pl ans—ei ther prec onfigured (built-in) or user-added t one plans .
5-373 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplns dsplns T o display all line conf iguration data for the current VI SM card, use the dsplns comman d in t he V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-374 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplnsta te dsplnstate T o di splay the ser vice state of speci.
5-375 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsplnto neplan dsplnto neplan T o di spla y the tone plan con figurat ion of a spec ified VISM card line , use the dsplntoneplan comma nd in the V oIP switchi ng/trunk ing and s witched AAL 2 PVC operati ng modes.
5-376 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplntone plan dsptonepro vplans Displa ys all use r-added (pr ovisional ) to ne p lans.
5-377 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl nton etim eo ut dsplntonetimeout T o di splay t he c onfigure.
5-378 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsplntone timeou t dsptoneplan Displ ays the ton e configurati on of a speci fied tone plan—ei ther a prec onfigured ( built-in ) o r user-adde d to ne pla n.
5-379 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspl oop s dsploop s T o display all li ne s and DS0 s th at are in th e lo opback c ond ition , use th e dsploops comman d in th e V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-380 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmaxm gcs dspma xmgcs T o d isp lay the maxi mu m numb er of .
5-381 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmgc dspmgc T o d ispl ay t he con figurati on data of a spe ci fied Medi a G ateway Cont rol (M G C), use the dspmgc comm an d in the V o IP switc hing/t runki n g and swi tched AA L2 PV C opera ting mod es.
5-382 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmgcgr pparam s dspmgcgrpparams T o d ispl ay a ll configure .
5-383 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmgcgrp protoc ols dspmgcgrpprotoco ls T o d ispl ay a ll config.
5-384 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmgcgr ps dspmgcgrps T o d ispl ay a ll configure d M edi a G.
5-385 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmgcs dspmgc s T o display conf iguration data ab out all conf i.
5-386 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmgpro tocol s dspmg protocols T o display data of all ca ll .
5-387 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmidcalltimers dspmidcalltimers T o display the con f igured par.
5-388 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmngci dcnt dspmn gcidcnt T o display the m anaged cha nnel i.
5-389 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmngcid cnt Relat ed Comma nds Ther e ar e no r ela te d comm an ds .
5-390 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspmonec anendp t dspmo necanendpt T o monitor the echo ca ncel.
5-391 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspmusicthr eshold dspmus icthreshold T o display th e music on- h.
5-392 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspnwc ot dspnwcot T o display the st atus—enabled or disa bl.
5-393 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspp ort dspport T o di splay con figuration da ta about the virtu.
5-394 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspprof params dspprofparams T o display th e prof ile elements an d the pr eferen ce for a ll prof iles, use th e dspprofparams command in the swit ched AAL2 PVC a nd AA L2 tru nking o per atin g mode s.
5-395 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsppr ofpara ms - - - - - - - - - - - - - - - - - - - - - - Profile Type : ITU Profile Number : 8 Profile Preference : 5 Voice Profile Codec : G.
5-396 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprscp rtn dsprsc prtn T o display conf iguration data ab out .
5-397 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprsvpif dsprsvpif T o display the Re source R eservation Proto c.
5-398 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprsvpreq dsprsvp req T o display the data associated with a s.
5-399 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprsvpr eq Relate d Comma nds Comm and De script ion cnfrsvp Configures RSVP for a sp ec ified co nne ct ion.
5-400 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprsvpreq s dsprsvp reqs T o displ ay all Resourc e Reservatio.
5-401 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprsvpresv dsprsvpresv T o display a ll d ata associ ated w ith a.
5-402 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprsvp resv Relat ed Comma nds C omman d Description cnfrsvp Configures RSVP for a spec ified co nne ct ion.
5-403 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprsvpresvs dsprsvpresv s T o displ ay all incom ing Resource Res.
5-404 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprsvps ender dsprsvp sender T o display all data associated w.
5-405 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprsvps ender rsvpSenderAdspecGuaranteedPathBw : 0 bps rsvpSender.
5-406 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprsvps enders dsprsvp senders T o displ ay all Re source Rese.
5-407 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprtp cnt dsprtp cnt T o display the bearer counters (statisti cs.
5-408 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprtpc nt dsplapdtrunkpvc Displa ys the assigned PVC tru nk type that ca rries LAPD trunk messages for the cu rrent VISM card.
5-409 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsp rtp con dsprtp con T o di splay the co nfiguration data of a s.
5-410 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprtpc on cnfrtpcon Modifies an existing sta tic R TP V oIP t ru nking conn ec tion.
5-411 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprtpconn stat dsprtp connstat T o display the Re al-T ime T rans.
5-412 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprtpc onnst at Relat ed Comma nds C omman d Des cription addrtpcon Adds a static R TP V o IP trunking connec tion.
5-413 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsprtpc ons dsprtp cons T o di splay the con figuration data of a .
5-414 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprtpc ons dsprtpcnt Displays the bearer c ounters (s tatistics) f or a spe cific R TP V oIP trunking connec tion.
5-415 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspr udptru nk dsprudptrunk T o d ispl ay the con figuration da ta.
5-416 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprudpt runk dsprtpcnt Displays the bearer c ounters (s tatistics) f or a spe cific R TP V oIP trunking connec tion.
5-417 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspr udptru nks dsprudptrunks T o di splay the configurat ion data.
5-418 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsprudpt runks dsprtpcnt Displays the bearer c ounters (s tatistics) f or a spe cific R TP V oIP trunking connec tion.
5-419 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspsar cnt dspsarcnt T o display th e segmenta tion and reassembly.
5-420 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspsarc nts dspsarcnts T o display the s e gm en tat ion and re.
5-421 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspsar msgcnt dspsarmsgcnt T o d isplay the se gmen tation an d re.
5-422 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspses dspses T o di splay the con figuration dat a of a Primary Rat e Interfac e (PRI) back haul sessi on, use the dspses comm an d in the V o IP switc hing/ tr unkin g and swi tch ed A AL2 PVC opera tin g mod e.
5-423 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsps esgr p dspsesgrp T o d ispl ay c on figuratio n dat a o f a P.
5-424 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspsesgrp s dspsesgrps T o d ispl ay c on figuratio n data abo .
5-425 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsps ess dspsess T o display config ura tion data ab out al l Primar y Rate Inter f ace (PRI) backhaul sessions, use the dspsess comm an d in the V oIP switc hing/t runki n g ope rat ing m od e.
5-426 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspses set dspsesset T o display conf iguration data about a sp.
5-427 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspsesstat dspsesstat T o disp lay con figuration d ata abou t Pri mary Rate Inter face (PRI) back haul sessi on statis tics (cou nters), use the dspsesstat comma nd in the V oIP switching /trunk ing operat ing mode.
5-428 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspslipc nt dspslipcnt T o displa y the curre nt clock slip cou.
5-429 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspsrcpcnt dspsrc pcnt T o display the Simple Resource Control Protocol (SRCP) message counters (statistics) for a specified call agent, use the dspsrcpcnt command in the V oIP switchi ng/trunk ing opera ting mo de.
5-430 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspsrcp cnts dspsrc pcnts T o displ ay the Simp le Resour ce Co.
5-431 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsps rcp peer dspsrc ppeer T o display th e peer con figu ration d.
5-432 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspsrcp peergrp params dspsrcppee rgrpparams T o display the Si.
5-433 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsps rc ppeer s dspsrc ppeers T o d ispl ay t he pee r c onfigura .
5-434 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspsrcp port dspsrcpport T o d is play the loc al Us er D atagr.
5-435 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspsrc pretry dspsrc pretry T o display the V ISM card le vel Simp.
5-436 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspt38 fxlco dspt38fxl co T o display the fax handling instruct.
5-437 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspt38fxl cos dspt38fxl cos T o display the fax handling instr uct.
5-438 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspt38 nsetime out dspt38nsetime out T o display a specifi ed c.
5-439 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspt38 nsetimeo uts dspt38nsetime outs T o display all conf igured.
5-440 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspt38 params dspt38params T o display the T .
5-441 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsptaski nfo dsptaski nfo T o display data about currentl y operating tasks, use the dsptaskinfo comm an d in th e V o IP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-442 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsptone builtinpl ans dsptonebuilt inplans T o display all buil.
5-443 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dsptone builtinpl ans Relat ed Comma nds C omma nd De scripti on addtoneplan Adds a to ne plan to th e curre nt VISM car d.
5-444 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsptone plan dsptone plan T o display the tone conf iguration o.
5-445 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspto neplan dsplntoneplan Displays th e tone plan conf iguration of a speci fied VISM card line.
5-446 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsptone plans dsptone plans T o display the tone conf iguration.
5-447 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspton eplans dsplntonetimeout Displays the conf igu red timeout periods for all call progress tone s of a specif ied VISM card line .
5-448 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsptone provplan s dsptone provplans T o display all provisional tone plan s, use the dsptoneprovplans command in the V o IP switching /trunk i ng an d s w itc hed AAL2 PV C opera ting mo des.
5-449 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspton eprovplans dsptonebuilt inplans Displa ys all prec onfigured (built-in ) tone plans on t he curre nt VISM card .
5-450 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dsptone regionpl ans dsptone regionplans T o d isplay a list of.
5-451 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspton eregio nplans dsptonebuilt inplans Displa ys all prec onfigured (built-in ) tone plans on t he curre nt VISM card .
5-452 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspvbd codec dspvbdc odec T o display th e upspe ed codec us ed for v oiceb and data (V BD), use the dspvbdcodec command in the V oIP switchin g/trunki ng operating mo de.
5-453 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspvbd pol dspvbdp ol T o di splay the VISM c ard level v o iceban.
5-454 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspvismdn dspvismd n T o di splay the domain na me of the c urren t VISM card, use the dspvismdn co mmand in the V oIP switching /trunk ing an d swi tched A AL2 PVC opera ting mo de s.
5-455 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspv ismi p dspvismi p T o display th e IP addres s and su bnet mask f or the cur rent VISM car d, use the dspvismip comm and i n the V oIP switching/trunking operating mode.
5-456 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspvismpa ram dspvismp aram T o displ ay VI SM card co nf igur ation para meter s, use the dspvismparam comm and in t he V oIP switching /trunking, switched AA L2 PVC, and AAL2 trun king opera ting mode s.
5-457 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspvismp aram cnfco4 time r Config ures the bearer con tinuity te st CO4 timer v alue. cnfcodectmpl As signs a code c template to an entire VISM card .
5-458 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspvoippa rams dspvoipparams T o di splay t h e V oIP sw itch ing/ trun king opera ti ng mode para m eters, use t he dspvoipparams comm an d in the V oIP switchi ng/trunk ing opera ting mo de.
5-459 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpbt dspxgc pbt T o di splay the default ne twork type, virtu.
5-460 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp calls dspxgc pcalls T o di splay the xGCP call ID, c on.
5-461 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspx gcp cids dspxgc pcids T o display the logical chan nel number.
5-462 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp cids dspxgcpcons Displa ys the xGCP conne ctio n ID, endpo int name, and call ID corr espond ing to each cal l agent est ablished c onnecti on on t he ga tew ay .
5-463 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspx gcpcnf dspxgc pcnf T o d ispl ay p reviously c onfigured Si m.
5-464 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp cnt dspxgc pcnt T o d isplay the Sim ple G ateway Contr.
5-465 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspx gcp cnts dspxgc pcnts T o d isplay the Sim ple G ateway Contr.
5-466 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp con dspxgc pcon T o display the attrib utes associated .
5-467 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspx gcp con Triple Redundancy = TRUE DTMF forwarding = FALSE Loca.
5-468 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp con MDCX Ack (MDCX Ack - CRCX) = 80.000000000 ms Time since the CRCX was received = 2016.930000000 sec (CRCX Command is not shown since it is used as reference) Codec List: Codec[1] = PCMA Pkt.
5-469 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxg cpcons dspxgc pcons T o display th e xGCP connec tion iden t.
5-470 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp defpkg dspxgc pdefpkg T o d isplay the Sim ple G ateway.
5-471 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpde tail cnt dspxgc pdetailcnt T o disp lay Sim ple Gateway .
5-472 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp detailcn ts dspxgc pdetailcnts T o disp lay Sim ple Gat.
5-473 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpen dpt dspxgc pendpt T o di splay the at tributes associ at.
5-474 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp endpt Relat ed Comma nds C omman d De scri ption delxgcpcon Deletes an xGCP connect ion specif ied b y the xGCP connect ion identif ication number .
5-475 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpend ptcons dspxgc pendptcons T o d i splay the at tri butes.
5-476 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp endptc ons MGC IP Address = Unknown MGC UDP Port = 2427 Port in Notified Entity = FALSE Protocol Version = MGCP 0.
5-477 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpend pts dspxgc pendpts T o displ ay the xGCP end point name.
5-478 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp errcnt dspxgcperrcn t T o d isplay the Sim ple G ateway.
5-479 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcpi nterops dspxgc pinterops T o d ispl ay the status of the .
5-480 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp lncons dspxgc plncons T o display th e DS0s with acti v.
5-481 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcppe ers dspxgc ppeers T o display all the User Datagram Prot.
5-482 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp persist evts dspxgcppersistev ts T o display all acti ve per sistent xGCP ev ents, use the dspxgc ppersistevt s command in the V oIP switching /trunk ing an d swi tched A AL2 PVC opera ting mo de s.
5-483 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands dspxgcppo rt dspxgcpport T o display th e local User Datagram Prot.
5-484 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands dspxgcp retry dspxgc pretry T o display the current xGCP retran.
5-485 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands Help Help T o display , in an alphabetical lis t, all commands ass.
5-486 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands pinglnd sp pinglndsp T o di splay the digi tal signal proc esso.
5-487 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands tstcon tstcon T o test a specif ie d con necti on, use th e tstcon comman d in the V oIP switching /trunki ng, swit ched AAL2 PVC, and AAL 2 trunking ope rating mod es.
5-488 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands tstdelay tstdelay T o test the delay on a specif ied connectio n, use the tstdelay comm and in the V o IP switchi ng/trunk ing, switched AAL 2 PVC, and AAL 2 trunking opera ting modes.
5-489 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands upco n upcon T o conf igure a speci f ied co nnecti on u p, al low.
5-490 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands versi on version T o displa y version-r elated data —such a s.
5-491 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 5 CLI Commands version Minor Release = 6 Build number = 4 DSPM C5421 T1 & E1 ECAN FW Details: Major Release = 8 Minor Release = 13 Build number = 0 Made by = swtools VxWorks (for R5k PDC) version 5.
5-492 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapter 5 CLI Co mmands versi on.
C HAPTER 6-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 6 Troubleshooting Tips Use t he fo llowing tr oub lesho oti ng t ools an d te chn.
6-2 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapt er 6 Trou bl esho otin g Tips VISM and PXM D isplay, Log, an d Diagnos tic Loopbac .
6-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 6 Troublesh ooting Tips VISM and PX M Di splay, L og, an d Diag nost ic Loop back P.
6-4 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapt er 6 Trou bl esho otin g Tips VISM and PXM D isplay, Log, an d Diagnos tic Loopbac .
6-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 6 Troublesh ooting Tips VISM Ala rms VISM Alarms Ta b l e 6 - 1 descr ibes VISM T1 and E1 card alarms. Refer to T1.4 03 for DS1 and G.
6-6 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapt er 6 Trou bl esho otin g Tips Symptoms and Solutions VISM Card Did Not Become Activ.
6-7 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 6 Troublesh ooting Tips Symptoms and Solutions 20 ------> No configuration file .
6-8 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapt er 6 Trou bl esho otin g Tips Symptoms and Solutions 1.4 Empty Clear 1.5 Failed VISM-8E1 Clear 1.6 Empty Clear 1.7 Active PXM1-OC3 Clear 1.
6-9 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Chapter 6 Troublesh ooting Tips Symptoms and Solutions FunctionModuleFWRev: 2.
6-10 Cisco VI SM Installati on and Co nfigur ation Guide Release 3.0, Part Number OL-2521-01 Rev. D0, June 2004 Chapt er 6 Trou bl esho otin g Tips Symptoms and Solutions Firmware Does Not S ee the C ard Insert Bit Status As Set This sy mptom can also indica te a bad VI SM card or bad MGX slot.
A-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 APPENDIX A VISM and VISM-PR Card Clocking Options An MGX 800 0 Series p latfo rm, co nsi sting of PXM and VISM cards, shoul d have one primary c lo cking source.
A- 2 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Re v. D0, June 2004 Appen dix A VISM and VI SM-PR C ard Cl ocking O ptions PXM1 Card as Prima ry Clocking .
A-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Appendix A VISM and VISM- PR Card Clocking Option s VISM Ca rd as Primary Clocki ng Sour ce.
A- 4 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Re v. D0, June 2004 Appen dix A VISM and VI SM-PR C ard Cl ocking O ptions PXM1E or PXM45 Card as Primary .
A-5 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Appendix A VISM and VISM- PR Card Clocking Option s Reverti ve and Nonreverti ve Cl ocking Rev ertiv e and nonrevertiv e clocki ng de pends upo n the p rocessor modul e back card u sed a nd the c locking source specif ied.
A- 6 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Re v. D0, June 2004 Appen dix A VISM and VI SM-PR C ard Cl ocking O ptions Revertive a nd Nonre vertive Cl.
B-1 Cisco VISM Installation and Configuration Guide Release 3.0, P art Number OL-25 21-01 Rev. D0, Jun e 2004 APPENDIX B VISM and VISM-PR—3.0 Specifications VISM Card Specifications • A TM la yer: Pe r ITU sta ndard s I. 36 1 and A TM UN I v3.1 • AAL layer: AAL5 as per stan dard I.
B-2 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Re v. D0, June 2004 Appen dix B VISM and V ISM-P R—3.0 Spec ificati ons VISM Card Phy sical Interfac e Sp.
B-3 Cisco VISM Installation and Configuration Guide Release 3.0, Pa rt Number OL-2521-01 Re v. D0, June 2004 Append ix B VISM and VISM-PR—3.0 Sp ecificatio ns VISM- PR Card Specif ications RT P / RT.
B-4 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Re v. D0, June 2004 Appen dix B VISM and V ISM-P R—3.0 Spec ificati ons VISM-PR Card Spe cifications – G.726-1 6k – G.726-2 4k – G.726-4 0k – G.723-H – G.
IN- 1 Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 INDEX Symbols ? comm and 5-2 A AAL2 p rofiles 4-39 AAL2 trun king appl icati on 2-3 .
Index IN-2 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004 clrc acfailcn trs comman d 5-56 clrmng cidc nt comm and 5-57 clrrtp cnt comm and.
Index IN- 3 Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 cnflnd igito rder co mman d 5-166 cnflng ain co mman d 5-167 cnflni s comm and.
Index IN-4 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004 VISM cloc king 4-14 connect ing cable s 1-16 connec tio n adm issi on cont ro l .
Index IN- 5 Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 dspcodec tmp ls comm a nd 5-329 dspco ncac comm and 5-332 dspconcn t c omm an .
Index IN-6 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004 dspslipc nt comm and 5-428 dspsmc nf comman d 6-6 dspsrcpc nt c om mand 5-429 ds.
Index IN- 7 Cisco VI SM Instal lation a nd Confi gurati on Guide Release 3.0 , Part Number OL-2 521-01 Rev. D0, June 2004 loopbac k configura tions 6-4 loopbac k paths 6-4 M mandat ory c om man ds 4-6.
Index IN-8 Cisco VI SM Installati on and Co nfigur atio n Guide Release 3.0, Part Number OL-2521-01 Rev. D0, Jun e 2004.
Een belangrijk punt na aankoop van elk apparaat Cisco Systems (VISM) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems (VISM) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems (VISM) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems (VISM) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems (VISM) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems (VISM) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems (VISM) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems (VISM) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
