Gebruiksaanwijzing /service van het product PA-T3 van de fabrikant Cisco Systems
Ga naar pagina of 74
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 P A-T3 Ser ial P or t Adapter .
.
Preface v Pref ace This preface describes ho w to find additional information on the P A-T3 and P A-2T3 serial port adapters and other Cisco products, services, and documentation.
Related Documentation vi PA-T3 Serial Port Adapter Installation and Configuration Related Documentation Y our router and the Cisco IOS software running on it contain extensi ve features and functional.
Preface vii Cisco Connection Online — Route Switch Module Catalyst VIP2-15 and VIP2-40 Installation and Configur ation Note (Document Number 78-4780-01) which shipped with your Catalyst RSM/VIP2 .
Cisco Documentation CD-ROM viii PA-T3 Serial Port Adapter Installation and Configuration A vailable 24 hours a day , 7 days a week, CCO provides a wealth of standard and value-added services to Cisco’ s customers and business partners.
CHAPTER Overview 1-1 1 Ov er vie w This chapter describes the one-port P A-T3 and two-port P A-2T3 serial port adapters. This chapter contains the following sections: • Port Adapter Overvie w , page.
PA-T3 Serial Port Adapter Features PA-T3 Serial Port Adapter Installation and Configuration 1-2 Figure 1-2 T wo-P ort P A-2T3 Serial Port Adapter The P A-T3 serial port adapter can be installed in the.
Overview 1-3 Management Information Base • Single-width port adapter for the Catalyst RSM/VIP2 in all Catalyst 5000 series switches • Single- or double-port T3 rate (45 Mbps) connectivity • Full.
Management Information Base PA-T3 Serial Port Adapter Installation and Configuration 1-4.
CHAPTER Preparing for Installation 2-1 2 Prepar ing f or Installation This chapter describes the general equipment, safety , and site preparation requirements for installing the P A-T3 port adapters.
Software and Hardware Requirements PA-T3 Serial Port Adapter Installation and Configuration 2-2 Software and Har dware Requirements T able 2-1 lists the minimum Cisco IOS software release required to use the P A-T3 and the P A-2T3 serial port adapters in supported router platforms.
Preparing for Installation 2-3 PA-T3 Port Adapter LEDs Note The VIP2 and Catalyst RSM/VIP2 supports online insertion and remov al (OIR), b ut indi vidual port adapters do not.
PA-T3 Port Adapter LEDs PA-T3 Serial Port Adapter Installation and Configuration 2-4 Figure 2-1 LEDs on the P A-T3 Serial Port Adapter—P artial Front View The P A-2T3 has one status LED and six uplink port status LEDs (RCLK, FERF , OOF , AIS, RL, and LL) for each serial P A-T3 port.
Preparing for Installation 2-5 PA-T3 Receptacles and Cables P A-T3 Receptacles and Cab les The P A-T3 port adapter serial interface cable, which is a 75-ohm coaxial cable, connects your router to a T3 serial network. Serial cables conform to EIA/TIA-612 and EIA/TIA-613 specifications.
Safety Guidelines PA-T3 Serial Port Adapter Installation and Configuration 2-6 Safety Guidelines Follo wing are safety guidelines that you should follo w when working with any equipment that connects to electrical power or telephone wiring. W arning This warning symbol means danger .
Preparing for Installation 2-7 Electrical Equipment Guidelines A viso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos.
FCC Class A Compliance PA-T3 Serial Port Adapter Installation and Configuration 2-8 Pre v enting Electrostatic Discharge Damage Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures.
Preparing for Installation 2-9 FCC Class A Compliance • Plug the equipment into an outlet that is on a dif ferent circuit from the television or radio. (That is, make certain the equipment and the tele vision or radio are on circuits controlled by dif ferent circuit breakers or fuses.
FCC Class A Compliance PA-T3 Serial Port Adapter Installation and Configuration 2-10.
CHAPTER VIP2 and the PA-T3 Port Adapter 3-1 3 VIP2 and the P A-T3 P or t Adapter This chapter provides information on the P A-T3 port adapter and its use on the VIP2 in Cisco 7000 series and Cisco 7500 series routers.
Overview PA-T3 Serial Port Adapter Installation and Configuration 3-2 Figure 3-1 VIP2-15 or VIP2-40 with One-P ort P A-T3 Serial P ort Adapters in P ort Adapter Slots 0 and 1 Note Port adapters hav e a handle attached, but this handle is not sho wn to allo w a full vie w of detail on each port adapter’ s faceplate.
VIP2 and the PA-T3 Port Adapter 3-3 Overview Figure 3-2 sho ws two one-port P A-T3 port adapters installed in port adapter slots 0 and 1 on a VIP2-50. Figure 3-2 VIP2-50 with One-P ort P A-T3 P ort Ad.
Removing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 3-4 When only one port adapter is installed on a VIP2, a blank port adapter must fill the empty slot.
VIP2 and the PA-T3 Port Adapter 3-5 Installing a Port Adapter Figure 3-4 Pulling a P ort Adapter Out of a Slot—Partial P ort Adapter View Step 7 If you remo ved a port adapter , place it in an antistatic container for safe storage or shipment back to the factory .
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 3-6 Caution T o prevent jamming the carrier between the upper and the lo wer edges of the port adapter slot and to en.
VIP2 and the PA-T3 Port Adapter 3-7 Installing a Port Adapter This completes the procedure for installing a port adapter on a VIP2. Proceed to Chapter 8, “Configuring the P A-T3 Interfaces, ” for information on how to configure your port adapter interfaces.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 3-8.
CHAPTER Catalyst RSM/VIP2 and the PA-T3 Port Adapter 4-1 4 Catalyst RSM/VIP2 and the P A-T3 P or t Adapter This chapter provides information on the P A-T3 serial port adapter and its use on the Catalyst RSM/VIP2 in the Catalyst 5000 series switches.
Overview PA-T3 Serial Port Adapter Installation and Configuration 4-2 Figure 4-1 Catalyst RSM/VIP2-15 or Catalyst RSM/VIP2-40 with One-P ort P A-T3 Serial P ort Adapters in P ort Adapter Slots 0 and 1 Note Port adapters hav e a handle attached, but this handle is not sho wn to allo w a full vie w of detail on each port adapter’ s faceplate.
Catalyst RSM/VIP2 and the PA-T3 Port Adapter 4-3 Removing a Port Adapter When only one port adapter is installed on a Catalyst RSM/VIP2, you must use a blank port adapter to fill the empty slot.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 4-4 Figure 4-3 Pulling a P ort Adapter Out of a Slot—Partial P ort Adapter View Step 7 If you remo ved a port adapter , place it in an antistatic container for safe storage or shipment back to the factory .
Catalyst RSM/VIP2 and the PA-T3 Port Adapter 4-5 Installing a Port Adapter Figure 4-4 Aligning a P ort Adapter in a Port Adapter Slot Caution T o prevent jamming the carrier between the upper and the .
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 4-6 Figure 4-5 Installing a P ort Adapter in a Port Adapter Slot—P artial Port Adapter View Step 4 Replace the scre w in the rear of the port adapter slot. (See Figure 4-2 for its location.
CHAPTER Cisco 7200 Series and the PA-T3 Port Adapter 5-1 5 Cisco 7200 Ser ies and the P A-T3 P or t Adapter This chapter provides information on the P A-T3 port adapter and its use in Cisco 7200 series routers.
Removing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 5-2 Note The Cisco 7200 series routers support online insertion and remov al; therefore, you do not hav e to po wer down the Cisco 7200 series routers when removing and replacing a port adapter .
Cisco 7200 Series and the PA-T3 Port Adapter 5-3 Installing a Port Adapter Caution Always handle the port adapter by the carrier edges and handle; ne v er touch the port adapter’ s components or connector pins.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 5-4 Step 5 W ith the metal carrier aligned in the slot guides, gently slide the port adapter halfway into the slot. Caution Do not slide the port adapter all the way into the slot until you hav e connected all required cables.
CHAPTER Cisco uBR7200 Series and the PA-T3 Port Adapter 6-1 6 Cisco uBR7200 Ser ies and the P A-T3 P or t Adapter This chapter provides information on the P A-T3 port adapter and its use in the Cisco uBR7200 series univ ersal broadband routers.
Removing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 6-2 Note Cisco uBR7200 series routers support OIR; therefore, you do not hav e to po wer down the router when removing and replacing a P A-T3 port adapter .
Cisco uBR7200 Series and the PA-T3 Port Adapter 6-3 Removing a Port Adapter Figure 6-3 Placing the P ort Adapter Lever in the Unlocked P osition—Cisco uBR7223 Step 3 Grasp the handle on the port adapter and pull the port adapter from the router midplane, about halfway out of its slot.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 6-4 Installing a P or t Adapter Follo wing is the procedure for installing a ne w port adapter in a Cisco uBR7200 series router: Step 1 Attach an ESD-pre venti v e wrist strap between you and an unfinished chassis surface.
Cisco uBR7200 Series and the PA-T3 Port Adapter 6-5 Installing a Port Adapter Figure 6-6 Placing the P ort Adapter Retention Clip in the Locked P osition—Cisco uBR7246 Shown • For a Cisco uBR7223, place the port adapter lever in the lock ed position.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 6-6.
CHAPTER Configuring the PA-T3 Interfaces 8-1 8 Configur ing the P A-T3 Interf aces T o continue your P A-T3 port adapter installation, you must configure the P A-T3 interfaces. The instructions that follow apply to all supported platforms. Minor dif ferences between the platforms are noted.
Using the EXEC Command Interpreter PA-T3 Serial Port Adapter Installation and Configuration 8-2 Using the EXEC Command Interpreter Y ou modify the configuration of your router through the software command interpreter called the EXEC (also called enable mode) .
Configuring the PA-T3 Interfaces 8-3 Cisco 7200 Series and Cisco uBR7200 Series Ports Note The I/O controller is av ailable with or without a Fast Ethernet port.
Identifying Port Adapter Slot and T3 Interface Port Numbers PA-T3 Serial Port Adapter Installation and Configuration 8-4 Figure 8-2 P A-T3 Interface Port Address Example—Cisco uBR7246 Y ou can ident.
Configuring the PA-T3 Interfaces 8-5 Catalyst RSM/VIP2 Ports For e xample, the serial port on a one-port P A-T3 serial port adapter in the first port adapter slot in chassis slot 3, is numbered 3/0/0. (See Figure 8-3.) If the P A-T3 serial port adapter is in port adapter slot 1, this same port is numbered 3/1/0.
Identifying Port Adapter Slot and T3 Interface Port Numbers PA-T3 Serial Port Adapter Installation and Configuration 8-6 Figure 8-4 P A-T3 Serial Port Adapter in the Catalyst 5509 Y ou can identify in.
Configuring the PA-T3 Interfaces 8-7 Shutting Down an Interface Slots in the Cisco 7140 series routers are numbered as sho wn in Figure 8-6. The fixed LAN interface is slot 0, the fixed W AN interfaces are slots 1 and 2, and the modular port adapter interface is slot 4.
Shutting Down an Interface PA-T3 Serial Port Adapter Installation and Configuration 8-8 Step 4 Enter the shutdown command as follows: Router(config-if)# shutdown Step 5 T o shut down additional interf aces, enter the slot/port address (or slot/port address/interface port for a VIP2) of each additional interface follo wed by the shutdown command.
Configuring the PA-T3 Interfaces 8-9 Shutting Down an Interface The example that follo ws is for Cisco 7100 series, Cisco 7200 series, or Cisco uBR7200 series routers: Router# show interfaces serial 1.
Performing a Basic Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-10 The example that follo ws is for a VIP2: Router(config)# interface serial 1/1/0 Router(config-if)# no shu.
Configuring the PA-T3 Interfaces 8-11 Configuration Example • For a VIP2, specify the interface to configure by entering the subcommand interface serial , follo wed by the slot/port-adapter/port (interface processor slot number , port adapter slot number , and interface port number).
Customizing the PA-T3 Serial Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 8-12 Customizing the P A-T3 Serial P ort Adapter Y ou can customize the P A-T3 serial port adapter . The features you can customize ha ve default v alues that probably suit your en vironment and do not require change.
Configuring the PA-T3 Interfaces 8-13 Specifying T3 Framing Note The local port configuration must match the remote port configuration. For e xample, if you enable scrambling on the local port, you must do the same on the remote port.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-14 For a Cisco 7100 series, Cisco 7200 series, or Cisco uBR7200 series router, use the follo wing example: router# configure terminal Enter configuration commands, one per line.
Configuring the PA-T3 Interfaces 8-15 Using show Commands to Display Interface and System Information Step 3 Specify one of the ne w interfaces: • For Cisco 7100 series, Cisco 7200 series, and Cisco.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-16 The following e xample of the show interfaces type slot/port command sho ws all of the information specific to.
Configuring the PA-T3 Interfaces 8-17 Using show Commands to Display Interface and System Information For a Catalyst RSM/VIP2, the show interfaces port-adapter/port command displays status information for the interfaces you specify . In this example, a one-port P A-T3 serial port adapter-configured Catalyst RSM/VIP2 is in port adapter slot 0.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-18 line state: down PA-T3 DTE cable, received clockrate 1582 base0 registers=0x3F000000, base1 registers=0x3F00200.
Configuring the PA-T3 Interfaces 8-19 Using show Commands to Display Interface and System Information 0 P-bit Err Secs, 0 P-bit Severely Err Secs 0 Severely Err Framing Secs, 0 Unavailable Secs 0 Line.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-20 byron uptime is 22 minutes System restarted by reload System image file is "c7200-p-mz", booted via tftp from 10.0.0.0 cisco 7206 (NPE150) processor with 12288K/4096K bytes of memory.
Configuring the PA-T3 Interfaces 8-21 Using show Commands to Display Interface and System Information T o determine which type of port adapter is installed in your system, use the show diag slot command.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-22 The following e xample sho ws a one-port P A-T3 serial port adapter on a Catalyst RSM/VIP2: router# show diag 0.
Configuring the PA-T3 Interfaces 8-23 Using show Commands to Display Interface and System Information Ethernet0/0/1, addr 00e0.f7d7.cb01 (bia 00e0.f7d7.cb01) gfreeq 48000148, lfreeq 48000180 (1536 bytes), throttled 0 rxlo 4, rxhi 273, rxcurr 0, maxrxcurr 0 txq 48001A08, txacc 48001A0A (value 0), txlimit 152 Ethernet0/0/2, addr 00e0.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-24 For complete command descriptions and e xamples for the Cisco 7100 series routers, Cisco 7200 series routers, Cisco uBR7200 series routers, VIP2 and Catalyst RSM/VIP2, refer to the publications listed in the “Related Documentation” section on page vi.
Configuring the PA-T3 Interfaces 8-25 Using the loopback Command to Verify the Physical Interface • Set the interface into local loopback mode as follo ws: Router# configure terminal Enter configuration commands, one per line.
Checking the Configuration PA-T3 Serial Port Adapter Installation and Configuration 8-26.
CHAPTER Cisco 7100 Series and the PA-T3 Port Adapter 7-1 7 Cisco 7100 Ser ies and the P A-T3 P or t Adapter This chapter provides information on the P A-T3 port adapter and its use in the Cisco 7100 series routers.
Removing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 7-2 Figure 7-2 Cisco 7140 Series Router—P ort Adapter Slot 4 Location Depending on your circumstances, you might need to install a new port adapter in a Cisco 7100 series router or replace a failed port adapter in the field.
Cisco 7100 Series and the PA-T3 Port Adapter 7-3 Installing a Port Adapter Figure 7-3 Handling a P ort Adapter Step 6 Place the port adapter on an antistatic surf ace with its components facing upward, or in a static shielding bag. If the port adapter will be returned to the factory , immediately place it in a static shielding bag.
Installing a Port Adapter PA-T3 Serial Port Adapter Installation and Configuration 7-4 Figure 7-4 Aligning the Single-Width P ort Adapter Between the Slot Guides Step 7 W ith the port adapter halfway in the slot, connect all required cables to the port adapter .
Een belangrijk punt na aankoop van elk apparaat Cisco Systems PA-T3 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Systems PA-T3 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Systems PA-T3 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Systems PA-T3 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Systems PA-T3 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Systems PA-T3 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Systems PA-T3 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Systems PA-T3 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
