Gebruiksaanwijzing /service van het product 247.795861 van de fabrikant Craftsman
Ga naar pagina of 16
OWNER'S MANUAL MODELNOS° 247.795860 247=795861 Caution: Readand Follow All Safety Rules and Instructions Before Operating This Equipment 8 HORSEPOWER 3 CUTTING STAGE MULCHING AND BAGGING CHIPPER=SHREDDER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO.
SAFETY RULES l_ PERSONAL INJURY, WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN TRAINING e Read t.
CC'NGRATULATIONS on your purchase of a Sears Crattsman Chipper-Shredder It has been designed, engi- neered and manufactured to give you the best possible dependability and performance, Should you.
TABLE OF CONTENTS ' SAFETY RULES ....................................................................... 2 PRODUCT SPECIFICATIONS ..................................... 3 WARRANTY ...................................................................
£ ASSEMBLY mNSTRUCTmONS IMPORTANT: This unit is shipped WITHOUT GASO_ LINE or OIL After assembly, see operation section of this manual for proper fuel and engine oil recommen- dation& NOTE: To determine right and left hand sides of your .
Spacers Hinge) Housing Assembly Hex Lock- Nut Hand Chute Deflector FIGURE 2. Stop Washer Upper Guide Release Assembly Bar Frame FIGURE 3. Hopper Pivot Door ASSEMBLE THIS TRUSS SCREW AND NUT FIRST Bar 8-3/8" Long Flat Washer Hex Lock Nut Hopl: Assembly Jper Guide Assembly pper Leaf Ramp Section Remove Truss Screw and Nut FIGURE 4.
e To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the draw- string, and pull on the drawstring until the bag is tight around the chute opening.
TO STOP ENGINE • Move engine shut-off switch to OFF position See figure 6 • Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended. e Close fuel shut-off valve when equipment is not in use to prevent fuel leakage.
® To lower the hopper assembly, use one hand to grasp the handle at the top of the hopper assembly and lift slightly Pull up on the release bar, and lower the hopper assembly to the ground Release the bar_ See figure 10 Hopper 5/ Release Bar FIGURE 10.
Check the fuel level periodically to avoid running out of gasoline while operating the chipper-shredder. If the unit runs out of gas as it is shredding or chipping, it may be necessary to unclog the unit before it can be restarted.
CUSTOMER RESPONSDBnLITIES MAINTENANCE SCHEDULE ,/___//_O_/ FILL IN DATES /_ ,/ _/ _ / ,_/a,,o_/^_,co/ .s REGULAR SERVICE ! / / / SERVICE ....... DATES F- Oil Pivot Points _/ O Clean Shredder q _1 rt C.
AIRCLEANER The air cleanerprevents damaging dirt, dust, etc., from entering the carburetor and being forced into the engine and is important to engine life and per- formance Never run your engine without air cleaner com- pletely assembled. To Service Air' Cleaner: Service pre-cleaner after every 25 hours of use, or at least once a season.
STORAGE ® Drain the fuel tank Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: NEVER STORE MACHINE WITH FUEL IN THE FUE.
Chute Deflector. Hairpin _ Clips, Clevis Pins --_Hex Nuts Washers Screen Chipper Chute FIGURE 19. Hand Knobs SHARPENING OR REPLACING THEBLADES CHIPPER BLADES ® Disconnect spark plug wire and move it away from spark plug e Remove the flail screen as instructed in previous section e Remove the chipper chute by removing three hex nuts and washers.
NGTE: Usecaution when removing the blade to avoid contacting the weld bolts on the housing_ e When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.
TROUBLE SHOOTING CORRECTIVE ACTION PROBLEM POSSIBLE CAUSE(S) Engine fails to start e Fuel shut-off valve closed. e Fuel tank empty, or stale fuel. e Spark plug wire disconnected e Faulty spark plug. Loss of power; e Spark plug wire loose. operation erratic • Unit running on CHOKE e Blocked fuel line or stale fuel.
Een belangrijk punt na aankoop van elk apparaat Craftsman 247.795861 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 247.795861 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 247.795861 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 247.795861 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 247.795861 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 247.795861 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 247.795861 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 247.795861 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
