Gebruiksaanwijzing /service van het product 77588 van de fabrikant Craftsman
Ga naar pagina of 26
Owner's Manual CRAFTSMAN 8.5 Horse Power CHIPPER-SHREDDER Model No. 247.77588O CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. 770-1228A Printed in U.
Content Page Content Page Warranty Information 2 Service & Adjustment 14 Safe Operation Practices 3 Off-Season Storage 16 Assembly 5 Trouble-Shooting 17 Operation 8 Repair Parts 18 Maintenance 11 .
This symbol points out important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder.
impeller tocome toa complete stop. The impeller continues torotate for a few seconds after the engine is shut off. Never place any part of the body in the impeller area untilyou are sure the impeller has stopped rotating. Muffler and engine become hot and can cause a bum.
Hopper* Chipper Chute Discharge Chute Bottle of Oil Safety Glasses Catcher Bag * The hopper is packed in the top insert in your chipper-shredder carton. Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine, Al_er assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up.
through hinge on discharge chute and housing (spacer fits inside of hinge). See figure 3 inset. Spac_er _-J-_ Hex Nut --Hex Bolt Hinge Hopper Pivot Door Inlet Guide Opening He_ Hopper Nut Wing Dischargl Figure 3 Place second spacer over hex bolt inside the other part of the hinge.
& WARNING; This flap control rod is a safety device to hold the flap in place inside the hopper while shredding branches. Do not operate the chipper-shredder without properly attachingthis flap control rod to the unit.
Read this owner's manual and safety rules before operating your chipper-shredder. Compare the illustration in figure 9 with your chipper-shredder to familiarize yourselfwith the location of various controls and adjustments. Save this manual for future reference.
WARNING: Before using yourchipper- shredder, again refer to the safety rules on pages 3 and 4 of this manual. Always be careful. GAS AND OIL FILL-UP Oil (Packed with unit) Only use high quality detergent oil rated with API service classification SF, SG or SH.
NOTE: TO prevent the unit fromsliding, place your foot firmly against the tire. 1. Attach spark plug wire -- 3. Move choke to "on" position 2. Place throttle in Fast Position 4. Pull rope Figure 1t Attach spark plug wire and rubber boot to spark plug.
changes (becomes stdngy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the shredding blade and/or chipper blades are dull and need to be sharpened or replaced. Refer to Service and Adjustments section.
CUSTOMER RESPONSIBILITIES o MAINTENANCE _ _ ..,P e,_P _3 =_ sc. oo, o,O { o ,v.C o,TEs Oil pivot points 0 Clean shredder _ a. Check engine oil ,,, Change engine oil <_ Service air cleaner ILl Clean engine _ Reset spark plug _ Clean muffler operatingtemperature.
If necessary, replace paper filter (do not attempt to clean). Installnew filter on base. Slide pre-cleaner over filter. Install cover and wing nut. Tighten wing nut securely. Clean Engine Clean engine periodically. Remove dirt and debris with a cloth or brush.
14.
REMOVING THE FLAIL SCREEN If the discharge area becomes clogged, remove the flail screen and clean area as follows. Stop engine, make certain the chipper- shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute.
Disconnect spark plug wire and move it away from spark plug. Lower the hopper assembly. Block up the housing. See figure 19. Weld Bolt Allen Screw Pipe cause damage to the unit.The blade can be tasted for balance by balancing it on a round shaft screwddver or nail.
Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. A WARNING: Never store machine with fuel in the fuel tank inside of building whe.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Engine fails to start 1. Fuel tank empty, orstale fuel 1. Fill tank with clean, fresh fuel 2. Spark plug wire disconnected 2. Connect wire to spark plug. 3. Faulty spark plug 3. Clean, adjust gap or replace. 4.
SEARS CRAFTSMAN 8.5 H.P. CHIPPER-SHREDDER MODEL 247.775880 6 29 12 21 5 14 18 97 33 13 74 52 56 85 88 63 65 80 79 91 19.
Key Part No No -- 770-1228A 1 11480 2 681-0118 3 681-0144 4 710-0542 710-0607 710-3256 7 712-0429 8 712-3027 9 714-0104 10 715-0129 11 726-0106 12 726-0135 13 728-0175 14 732-0546 15 732-0629 16 735-0.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 35 4OO 310 3O5 757 87 7O 69 2g0 101 1t0 182 251 21.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. -- m 1 35385 2 27652 4 5 30969 15 30699C 15A 17 18 19 20 25 26 28 30 35 38 37 38 40 40 41 41 42 .
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247,775880 Key Part No. No. 185 34707 186 34667 200 34677 203 31342 204 651029 206 610973 207 33878 209 650821 215 35882 223.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Carburetor Key Part Description No. No. 640112 1 631776A 2 631970 4 631184 ,.
SEARS CRAFTSMAN 8.5 H.P. ENGINE MODEL 143.988503 FOR CHIPPER-SHREDDER MODEL 247.775880 Recoil Starter 590746 13 12 "8 6_'_6 ¢p-.4 Key Part Description No. No. 590746 1 590599A 2 590600 3 590679 4 590601 5 590678 6 590680 7 590412 8 590681 11 590747 12 590535 13 590701 Recoil Starter Spring Pin (Incl.
For the repair or replacement partsyou need delivered directlyto your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7.
Een belangrijk punt na aankoop van elk apparaat Craftsman 77588 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 77588 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 77588 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 77588 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 77588 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 77588 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 77588 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 77588 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
