Gebruiksaanwijzing /service van het product AVR-X5200W van de fabrikant Denon
Ga naar pagina of 335
. AVR-X5200W INTEGRATED NETWORK AV RECEIVER Owner’s Manual You can print more than one page of a PDF onto a single sheet of paper. Contents Connections Playback Settings Tips Appendix 1 Front panel .
Accessories 8 Inserting the batteries 9 Operating range of the remote control unit 9 Features 10 High quality sound 10 High performance 11 Easy operation 14 Part names and functions 15 Front panel 15 .
Playback Basic operation 75 Turning the power on 75 Selecting the input source 75 Adjusting the volume 76 Turning off the sound temporarily (Muting) 76 Playback a DVD player/Blu-ray Disc player 76 Pla.
Viewing photographs on the Flickr site 109 Viewing photographs shared by particular users 110 Viewing all photographs on Flickr 112 AirPlay function 113 Playing songs from your iPhone, iPod touch or i.
Selecting a sound mode 128 Selecting a sound mode 129 Direct playback 130 Pure Direct playback 130 Auto surround playback 131 HDMI control function 143 Setting procedure 143 Sleep timer function 144 U.
Inputs 190 Input Assign 190 Source Rename 192 Hide Sources 192 Source Level 192 Input Select 193 Speakers 194 Audyssey ® Setup 194 Procedure for speaker settings (Audyssey ® Setup) 196 Error messages 202 Retrieving Audyssey ® Setup settings 204 Manual Setup 205 Amp Assign 205 Speaker Config.
Operating external devices with the remote control unit 249 Registering preset codes 250 Operating devices 252 Initializing registered preset codes 255 Specifying the operating zone with the remote co.
Thank you for purchasing this Denon product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference. Accessories Check that the following parts are supplied with the product.
Inserting the batteries 1 Slide the rear cover off the remote control unit in the arrow direction. . 2 Insert two batteries correctly into the battery compartment as indicated. . R6P/AA batteries 3 Put the rear cover back on. NOTE 0 To prevent damage or leakage of battery fluid: 0 Do not use a new battery together with an old one.
Features High quality sound 0 With discrete circuit technology, the power amplifier provides identical quality for all 9-channels (175 Watts x 9-channels) For optimum realism and stunning dynamic range, the power amplifier section features discrete power devices (not integrated circuitry).
High performance 0 4K 60Hz input/output supported . 4K 60p 4:4:4 4K 60p 4:4:4 When 4K Ultra HD (High Definition) is used, an input/output speed of 60 frames per second (60p) is achieved for video signals.
0 HDMI connections enable connection to various digital AV devices (8 inputs, 3 output) . 83 / Out In For connection to a broad range of digital sources, this unit features 8 HDMI inputs, including 1 on the front panel that lets you quickly and conveniently connect a camcorder, game console or other HDMI- equipped device.
0 Wireless connection with Bluetooth devices can be carried out easily ( v p. 85) . You can enjoy music simply by connecting wirelessly with your smartphone, tablet, PC, etc.
Easy operation 0 “Setup Assistant” provides easy-to-follow setup instructions First select the language when prompted. Then simply follow the instructions displayed on the TV screen to set up the speakers, network, etc. 0 Easy to use Graphical User Interface This unit is equipped with a Graphical User Interface for improved operability.
Part names and functions Front panel . u w qt r e y A B C D E F G Contents Connections Playback Settings Tips Appendix 15 Front panel Display Rear panel Remote Index.
. e w qr t y u A Power operation button ( X ) Used to turn the power of the MAIN ZONE (room where this unit is located) on/off (standby). ( v p. 75) B Power indicator This is lit as follows according to the power status: 0 Green : Power on 0 Off: Normal standby 0 Red: 0 When “HDMI Pass Through” is set to “On” ( v p.
With the door open . io Q 0 qw rt yu e A ZONE2 ON/OFF button This turns the power of ZONE2 on/off. ( v p. 156) B ZONE2 SOURCE button This selects the input source for ZONE2. ( v p. 156) C ZONE3 ON/OFF button This turns the power of ZONE3 on/off. ( v p.
. Q 3 Q 4 Q 8 Q 1 Q 2 Q 7 Q 6 Q 5 K AUX1 HDMI connector This is used to connect HDMI output compatible devices such as video camcorders and game consoles. ( v p. 63) L USB port This is used to connect USB storages (such as USB memory devices) and the USB cable supplied with iPod.
Display . Q0 Q1 Q2 i uo y t r e w q G H I J K L A Input signal indicators The respective indicator will light corresponding to the input signal. ( v p. 193) B Decoder indicators These light when Dolby or DTS signals are input or when the Dolby or DTS decoder is running.
. Q0 Q1 Q2 i uo G Sleep timer indicator This lights when the sleep mode is selected. ( v p. 145) H MUTE indicator This blinks while the sound is muted. ( v p. 76, 157) I Volume indicator J Information display The input source name, sound mode, setting values and other information are displayed here.
Rear panel . 1 CBL/SAT PHONO 1 CBL/SAT 2 DVD 2 CD 1 TV AUDIO 6 MEDIA PLAYER 2 DVD 12 3 Blu-ray 5 CD 4 GAME 1 CBL/SAT 1 CBL/SAT 2 DVD 2 DVD 4 GAME (ASSIGNABLE) DIGITAL AUDIO RS-232C REMOTE CONTROL TRIG.
. 1 CBL/SAT PHONO 1 CBL/SAT 2 DVD 2 CD 1 TV AUDIO 6 MEDIA PLAYER 2 DVD 12 3 Blu-ray 5 CD 4 GAME 1 CBL/SAT 1 CBL/SAT 2 DVD 2 DVD 4 GAME (ASSIGNABLE) DIGITAL AUDIO RS-232C REMOTE CONTROL TRIGGER OUT AUD.
. 1 CBL/SAT PHONO 1 CBL/SAT 2 DVD 2 CD 1 TV AUDIO 6 MEDIA PLAYER 2 DVD 12 3 Blu-ray 5 CD 4 GAME 1 CBL/SAT 1 CBL/SAT 2 DVD 2 DVD 4 GAME (ASSIGNABLE) DIGITAL AUDIO RS-232C REMOTE CONTROL TRIGGER OUT AUD.
Remote control unit . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AV R CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L /.
. SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AV R CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L / SAT Blu-ray Blu- ra.
. SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AV R CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L / SAT Blu-ray Blu- ra.
o Contents Connecting speakers 28 Connecting a TV 55 Connecting a playback device 59 Connecting an iPod or USB memory device to the USB port 65 Connecting an FM/AM antenna 67 Connecting to a home netw.
Connecting speakers Install speakers and connect them to this unit. ( v p. 28, 35) Speaker installation Determine the speaker system depending on the number of speakers you are using and install each speaker and subwoofer in the room. Speaker installation is explained using this example of a typical installation.
. FHL FHR TRR TRL TFR TFL RHL RHR TMR TML FHL/FHR (Front height speaker left/ right) : Place the FRONT HEIGHT left and right speakers directly above the front speakers. Mount them as close to the ceiling as possible and aim them towards the main listening position.
. FDL FDR BDL BDR SDL SDR FDL/FDR (Front Dolby speaker left/ right) : Place the FRONT DOLBY ENABLED speaker on the front speaker. For a Dolby enabled speaker integrated with a front speaker, place the Dolby enabled speaker instead of the front speaker.
0 This unit is compatible with Audyssey DSX ® , Dolby Atmos and DTS Neo:X which offers an even wider and deeper surround sensation. ( v p. 295, 296, 299) When using Audyssey DSX ® , install front wide speakers or front height speakers. 0 Use the illustration below as a guide for how high each speaker should be installed.
o When 7.1-channel speakers are installed using surround back speakers . z 1 z 2 z 3 FL SW C SL SBL FR SR SBR Listening position z 1:22° - 30° z 2:90° - 110° z 3:135° - 150° When using a single surround back speaker, place it directly behind the listening position.
o When 5.1-channel speakers are installed . z 1 z 2 FL SW C SL FR SR z 1:22° - 30° z 2:120° Contents Connections Playback Settings Tips Appendix 33 Front panel Display Rear panel Remote Index.
o Layout including height speakers and top speakers n Dolby Atmos layout example Combination of 7.1-channel layout with surround back speaker and top front/top rear speakers. . C FL FR SBL SBR SW TRR TRL TFR TFL SL SR n DTS Neo:X layout example Combination of 9.
Speaker connection Here we connect the speakers in the room to this unit. This section explains how to connect them using typical examples. NOTE 0 Disconnect this unit’s power plug from the power outlet before connecting the speakers. Also, turn off the subwoofer.
o Connecting the speaker cables Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to this unit, and be sure to connect the channels and polarities correctly.
o About the speaker cable label (supplied) for channel identification The channel display section for speaker terminals on the rear panel is color-coded for each channel to be identifiable.
Speaker configuration and “Amp Assign” settings This unit has a built-in 9-channel power amplifier. In addition to the basic 5.1-channel system, a variety of speaker systems can be configured by changing the “Amp Assign” ( v p. 205) settings to suit the application, such as 7.
In addition to the connections described in ( v p. 40 - 54), this unit allows for various speaker connections with the “Amp Assign” setting. Also refer to the menu screen in “View Terminal Config.” on the “Amp Assign” setting screen, which shows how to make connections in your environment.
o Standard configuration and connection n 5.1-channel playback This serves as a basic 5.1-channel surround system. . FL SW C SL FR SR . 1 CBL/SAT 1 CBL/SAT 2 DVD 2 CD 1 TV AUDIO 6 MEDIA PLAYER 2 DVD 12 3 Blu-ray 5 CD 4 GAME (ASSIGNABLE) DIGITAL AUDIO RS-232C REMOTE CONTROL TRIGGER OUT COAXIAL OPTICAL STRAIGHT CABLE IR DC12V 150mA MAX.
n 7.1-channel playback (surround back) This 7.1-channel surround system is the same as a basic 5.1-channel system but with surround back speakers. . FL SW SL FR SR SBR SBL .
o Advanced connections n 9.1-channel playback This system, which is based on a 5.1-channel system, plays back up to 9.1-channels at the same time. You can connect speakers for up to 11-channels for MAIN ZONE. When you connect speakers for 10 or more channels, the output speakers automatically switch according to the input signal and sound mode.
n 11.1-channel playback This system, which is based on a 5.1-channel system, plays back up to 11.1-channels at the same time. You can connect speakers for up to 13-channels for MAIN ZONE by using an external power amplifier.
n 7.1-channel playback (bi-amp connection of front speakers) This system plays back 7.1-channels. You can use the bi-amp connection for front speakers. Bi-amp connection is a method to connect separate amplifiers to the tweeter terminal and woofer terminal of a speaker that supports bi-amplification.
n Exclusive 9.1-channel playback + 2-channel playback speakers You can connect speakers used exclusively for 2-channel playback, which are used for the direct and stereo modes, and speakers used exclusively for 9.
n Exclusive 7.1-channel playback + 2-channel playback (bi-amp connection) speakers You can connect speakers used exclusively for 2-channel playback, which are used for the direct and stereo modes, and speakers used exclusively for 7.1 multi-channel playback.
n 7.1-channel playback + front speakers of second unit This system enables switching playback between front speakers A and B as desired. You can connect speakers for up to 9-channels for MAIN ZONE. When you connect speakers for 8 or more channels, the output speakers automatically switch according to the input signal and sound mode.
n 7.1-channel playback (MAIN ZONE) + 2-channel playback (ZONE2 or ZONE3) This type of configuration plays back 7.1-channels in MAIN ZONE and 2-channels in ZONE2. (Speakers can output audio from ZONE3 instead of ZONE2 (Assign Mode: 7.1ch + ZONE3).) You can connect speakers for up to 9-channels for MAIN ZONE.
n 5.1-channel playback (bi-amp connection of front speakers: MAIN ZONE) + 2-channel playback (ZONE2) This type of configuration plays back 5.1-channels in MAIN ZONE and 2-channels in ZONE2. You can use the bi-amp connection for front speakers in MAIN ZONE.
n 5.1-channel playback (MAIN ZONE) + 2-channel playback (ZONE2) + 2-channel playback (ZONE3) This type of configuration plays back 5.1-channels in MAIN ZONE and 2-channels in ZONE2 and ZONE3. . FL SW C SL FR SR ZONE2 L ZONE2 R ZONE3 L ZONE3 R MAIN ZONE ZONE2 ZONE3 .
n 7.1-channel playback (MAIN ZONE) + 1-channel playback (ZONE2) + 1-channel playback (ZONE3) This type of configuration plays back 7.1-channels in MAIN ZONE and 1-channel (monaural) in ZONE2 and ZONE3. You can connect speakers for up to 9-channels for MAIN ZONE.
o Dolby Atmos This speaker configuration is optimized for Dolby Atmos playback. n 11.1-channel system This system configuration plays back 11.1-channels by using an external power amplifier.
n 9.1-channel system This configuration uses only this unit for Dolby Atmos playback. . C FL FR SBL SBR SW SL SR TMR TML . 1 CBL/SAT 1 CBL/SAT 2 DVD 2 CD 1 TV AUDIO 6 MEDIA PLAYER 2 DVD 12 3 Blu-ray 5 CD 4 GAME (ASSIGNABLE) DIGITAL AUDIO RS-232C REMOTE CONTROL TRIGGER OUT COAXIAL OPTICAL STRAIGHT CABLE IR DC12V 150mA MAX.
o Connecting an external power amplifier You can use this unit as a pre-amp by connecting an external power amplifier to the PRE OUT connectors. By adding a power amplifier to each channel, the realness of the sound can be further enhanced. Select the terminal to use and connect the device.
Connecting a TV Connect a TV to this unit so that the input video is output to the TV. You can also enjoy audio from the TV on this unit. How to connect a TV depends on the connectors and functions equipped on the TV. ARC (Audio Return Channel) function plays TV audio on this unit by sending the TV audio signal to this unit via HDMI cable.
Connection 1 : TV equipped with an HDMI connector and compatible with the ARC (Audio Return Channel) Use an HDMI cable to connect a TV that is compatible with the ARC function to this unit. Set “HDMI Control” to “On” when using a TV that supports the ARC function.
Connection 2 : TV equipped with an HDMI connector and incompatible with the ARC (Audio Return Channel) Use an HDMI cable to connect the TV to this unit.
Connection 3 : TV equipped without an HDMI connector Use a component video or a video cable to connect the TV to this unit. To listen to audio from TV on this unit, use an optical cable to connect the TV to this unit.
Connecting a playback device This unit is equipped with three types of video input connectors (HDMI, component video and composite video) and three types of audio input connectors (HDMI, digital audio and audio). Select input connectors on this unit according to the connectors equipped on the device you want to connect.
Connecting a set-top box (Satellite tuner/cable TV) This explanation uses the connection with a satellite tuner/cable TV STB as an example. Select the input connectors on this unit to match the connectors on the device that you want to connect to.
Connecting a DVD player or Blu-ray Disc player This explanation uses the connection with a DVD player or Blu-ray disc player as an example. Select the input connectors on this unit to match the connectors on the device that you want to connect to.
Connecting a Blu-ray Disc player compatible with the Denon Link HD function By making a Denon Link HD connection to a player compatible with the Denon Link HD function, you can enjoy higher quality playback compared with when only the HDMI connector connection is made.
Connecting a video camcorder or game console This explanation uses the connection with a video camcorders as an example. Connect a playback device to this unit, such as a video camcorder or game console.
Connecting a turntable This unit is compatible with turntables equipped with a moving magnet (MM) phono cartridge. When you connect to a turntable with a low output moving coil (MC) cartridge, use a commercially available MC head amp or a step-up transformer.
Connecting an iPod or USB memory device to the USB port To connect an iPod to this unit, use the USB adapter cable that was supplied with the iPod. For operating instructions see “Playing an iPod” ( v p. 77) or “Playing a USB memory device” ( v p.
o Supported iPod/iPhone models . • iP od classic • iP od nano • iP od touc h • iPhone Contents Connections Playback Settings Tips Appendix 66 Front panel Display Rear panel Remote Index.
Connecting an FM/AM antenna Connect the antenna, tune in to a broadcast and then move the antenna to the location where there is least noise. Then use tape, etc. to fix the antenna in this location. (“Listening to FM/AM broadcasts” ( v p. 91)) If you are unable to receive a good broadcast signal, we recommend installing an outdoor antenna.
o Using the AM loop antenna Suspending on a wall Suspend directly on a wall without assembling. . Nail, tack, etc. Standing alone Use the procedure shown above to assemble.
Connecting to a home network (LAN) This unit can connect to a network using a wired LAN or wireless LAN. You can connect this unit to your home network (LAN) to enable various types of playback and operations as described below.
Wireless LAN When connecting to the network via wireless LAN, connect the external antennas for Bluetooth/wireless connectivity connection to the rear panel and stand them upright. See “Wi-Fi Setup” ( v p. 232) on how to connect to a wireless LAN router.
Connecting an external control device REMOTE CONTROL jacks When this unit is installed in a location where the remote control signals cannot reach (installation in a cabinet etc.), it can still be controlled by the remote control by connecting a remote control receiver unit (sold separately).
TRIGGER OUT jacks When a device with TRIGGER IN jack is connected, the connected device’s power on/standby can be controlled through linked operation to this unit.
Connecting the power cord After completing all the connections, insert the power plug into the power outlet. . 1 CBL/SAT 1 CBL/SAT 2 DVD 2 DVD 4 GAME (ASSIGNABLE) DIGITAL AUDIO (ASSIGNABLE) (ASSIGNABL.
o Contents Basic operation Turning the power on 75 Selecting the input source 75 Adjusting the volume 76 Turning off the sound temporarily (Muting) 76 Selecting a sound mode 128 Playback a device Play.
Basic operation . SOUND MODE SOUND MODE AVR CONTROL AVR CONT ROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VIE GAME GA ME MUSIC MU SI C OPTION OPTIO N INFO INFO BACK BACK SETUP.
Adjusting the volume 1 Use VOLUME df to adjust the volume. 0 The variable range differs according to the input signal and channel level setting. 0 You can also adjust the master volume by turning MASTER VOLUME on the main unit. Turning off the sound temporarily (Muting) 1 Press MUTE : .
Playing an iPod . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SAT B.
Listening to music on an iPod 1 Connect the iPod to the USB port. ( v p. 65) 2 Press iPod/USB to switch the input source to “iPod/ USB”. “Browse from iPod” is displayed on the display of this unit. 0 Nothing is displayed on the TV screen. 3 Operate iPod itself while seeing the iPod screen to play back music.
iPod Browse Mode settings In this mode, various lists and screens during playback on the iPod are displayed on the TV screen. This section describes the steps up to playing back tracks on the iPod in “On-Screen”. 1 Press OPTION when the input source is “iPod/USB”.
o Operations accessible through the option menu This can be operated when the “iPod Browse Mode” is set to “On- Screen”. ( v p. 79) 0 “iPod Browse Mode settings” ( v p. 79) 0 “Performing repeat playback” ( v p. 81) 0 “Performing random playback” ( v p.
Performing repeat playback 1 Press OPTION with “iPod Browse Mode” set to “On- Screen”. The option menu screen is displayed. 2 Use ui to select “Repeat”, then press ENTER. 3 Use o p to select repeat playback mode. Off (Default) : Repeat playback mode is canceled.
Playing a USB memory device . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB.
Playing files stored on USB memory devices 1 Connect the USB memory device to the USB port. ( v p. 65) 2 Press iPod/USB to switch the input source to “iPod/ USB”. . Folder1 Folder2 Folder3 Music1 Music2 Music3 Music4 OPTION OPTION USB [1/9] Option 3 Use ui p to select the file to be played, then press ENTER.
o Operations accessible through the option menu 0 “Performing repeat playback” ( v p. 118) 0 “Performing random playback” ( v p. 118) 0 “Searching content with keywords (Text Search)” ( v p. 120) 0 “Playing back music and a favorite picture at the same time (Slideshow)” ( v p.
Listening to music on a Bluetooth device . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C.
Pairing with a Bluetooth device In order to enjoy music from a Bluetooth device on this unit, the Bluetooth device must first be paired with this unit. Once the Bluetooth device has been paired, it does not need to be paired again. 1 Prepare for playback.
Playing a Bluetooth device Check the following before you play back music. 0 The Bluetooth function of the Bluetooth device must be turned on 0 Pairing must be completed 1 Press Bluetooth to switch the input source to “Bluetooth”. The unit will automatically connect to the most recently used Bluetooth device.
NOTE 0 To operate the Bluetooth device with the remote control of this unit, the Bluetooth device needs to support the AVRCP profile. 0 The remote control of this unit is not guaranteed to work with all Bluetooth devices.
Pairing with the Pairing Mode Pair a Bluetooth device with this unit. 1 Press OPTION when the input source is “Bluetooth”. The option menu screen is displayed. 2 Use ui to select “Pairing Mode”, then press ENTER. The device will go into the pairing mode.
Listening to FM/AM broadcasts . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SAT Blu-ray.
Listening to FM/AM broadcasts 1 Connect the antenna. (“Connecting an FM/AM antenna” ( v p. 67)) 2 Press TUNER to switch the input source to “Tuner”. G TV screen H . TUNE+/- TUNE+/- STEREO AUTO CH / CH / OPTION OPTION Tuner FM 87.50MHz Now Playing Tune Preset Option CH 1 G Display of this unit H .
o Operations accessible through the option menu 0 “Tuning in by entering the frequency (Direct Tune)” ( v p. 93) 0 “RDS search” ( v p. 93) 0 “PTY search” ( v p. 94) 0 “TP search” ( v p. 95) 0 “Radio Text” ( v p. 95) 0 “Changing the tune mode (Tune Mode)” ( v p.
Tuning in by entering the frequency (Direct Tune) You can enter the receiving frequency directly to tune in. 1 Press OPTION when the input source is “Tuner”. The option menu screen is displayed. 2 Use ui to select “Direct Tune”, then press ENTER.
PTY search Use this function to find RDS stations broadcasting a designated program type (PTY). PTY identifies the type of RDS program. The program types and their displays are as follows: NEWS News W.
TP search TP identifies programs that carry traffic announcements. This allows you to easily find out the latest traffic conditions in your area before leaving home. Use this function to find RDS stations broadcasting traffic programs (TP stations). 1 Press OPTION when the input source is “Tuner”.
Changing the tune mode (Tune Mode) You can change the mode for tuning into FM and AM broadcasts. If you cannot tune in automatically with “Auto” mode, change the mode to “Manual” and tune in manually. 1 Press OPTION when the input source is “Tuner”.
Presetting the current broadcast station (Preset Memory) Your favorite broadcast stations can be preset so that you can tune them in easily. Up to 56 stations can be preset. 1 Tune in the broadcast station you want to preset. (“Listening to FM/AM broadcasts” ( v p.
Specify a name for the preset broadcast station (Preset Name) You can set the name to the preset broadcast station or change it. Up to eight characters can be input. 1 Press OPTION when the input source is “Tuner”. The option menu screen is displayed.
Skipping preset broadcast stations (Preset Skip) Perform auto preset memory to save all the broadcasting stations that can be received in the memory. Selecting a broadcast station becomes easier by skipping unnecessary memories. 1 Press OPTION when the input source is “Tuner”.
Cancelling Preset Skip 1 Use o p to select a group containing a broadcast station to cancel the skip for while the “Preset Skip ” screen is displayed. 2 Use ui to select a broadcast station to cancel the skip for. 3 Use o p to select “On”. The skip is cancelled.
Listening to Internet Radio . POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT GAME GAME CB CB L/ SAT Blu-ray Blu- ray D VD VD AUX1 AUX1 AUX2 AUX2 INTE RNET R ADIO ADIO iPo iPo d/ USB USB VOLUME VO LUM E INFO INFO SETUP SETU P MENU MEN U Z 2 Z 3 Z 3 1 2 3 4 MAIN MAI N PHONO PH ON O DE V.
Listening to Internet Radio 1 Prepare for playback. 0 Check the network environment, then turn on this unit’s power. (“Connecting to a home network (LAN)” ( v p. 69)) 2 Press ONLINE MUSIC. 0 You can also press INTERNET RADIO to select the input source “Internet Radio” directly.
5 Use ui p to select the station, then press ENTER. Playback starts once buffering reaches “100%”. Operation buttons Function 1 Playback 2 Stop ENTER (Press and hold) Stop CH/PAGE d f Switch to the previous page/next page in the list display 0 The display switches between track title and radio station name etc.
Using vTuner to add Internet Radio stations to favorites There are many Internet Radio stations in the world, and this unit can tune into these stations. But finding the radio station you want to hear may be difficult, because there are too many stations.
Playing back files stored on a PC and NAS . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI .
Applying media sharing settings Here, we apply the settings to share music files stored on a PC and NAS on the network. If you are using a Media Server, be sure to apply this setting first. . o When using Windows Media Player 12 (Windows 7 / Windows 8) 1 Start up Windows Media Player 12 on the PC.
Playing back files stored on a PC and NAS Use this procedure to play music files, image files or playlists. 1 Prepare for playback. A Check the network environment, then turn on this unit’s power. (“Connecting to a home network (LAN)” ( v p. 69)) B Prepare the computer.
0 The display switches between track title, artist name, and album title each time the main unit’s STATUS is pressed. 0 When a WMA (Windows Media Audio), MP3 or MPEG-4 AAC file includes album art data, the album art can be displayed while the music files are playing.
Viewing photographs on the Flickr site . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SA.
Viewing photographs shared by particular users 1 Prepare for playback. 0 Check the network environment, then turn on this unit’s power. (“Connecting to a home network (LAN)” ( v p. 69)) 2 Press ONLINE MUSIC. 3 Use uio p to select “Flickr”, then press ENTER.
8 Use ui to select the folder, then press ENTER. Favorites : Displays the favorite photographs of the specified user. Photostream : Displays a list of shared photographs. PhotoSets : Displays the folder (photograph album) list. Contacts : Displays the screen name used by the specified user in Contacts.
Viewing all photographs on Flickr 1 Use ui to select “All Content”, then press ENTER. 2 Use ui to select the folder, and then press ENTER. Interestingness : Displays photographs that are popular from the number of user comments or number of times they are added as favorites.
AirPlay function Music files stored on your iPhone, iPod touch, iPad or iTunes can be played on this unit via the network. 0 + is displayed on the menu screen while AirPlay is being operated. 0 Source input will be switched to “Online Music” when AirPlay playback is started.
Playing songs from your iPhone, iPod touch or iPad If you update your “iPhone/iPod touch/iPad” to iOS 4.2.1 or later, you can stream music stored in your “iPhone/iPod touch/iPad” directly to this unit. 1 Connect your iPhone, iPod touch or iPad Wi-Fi to the same network as this unit.
Selecting multiple speakers (devices) It is possible to play iTunes songs on your home’s AirPlay compatible speakers (devices) other than those of this unit. 1 Click the AirPlay icon ' and select “Multiple”. 2 Check the speakers you want to use.
Spotify Connect function Spotify is the world’s most popular streaming service. If you subscribe to Spotify Premium, you can control your new speaker with your phone or tablet. Because Spotify is built-in to your speaker, you can still take calls or use other apps - the music never stops.
Convenience functions . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SAT Blu-ray Blu- ra.
Performing repeat playback n Supported input sources : USB / Media Server / Bluetooth 1 While content is playing, press OPTION. The option menu screen is displayed. 2 Use ui to select “Repeat”, then press ENTER. 3 Use o p to select repeat playback mode.
Registering to Favorites You can register a total of 100 favorites. o Supported input sources: Internet Radio / Media Server 1 While content is playing, press OPTION. The option menu screen is displayed. 2 Use ui to select “Save to Favorites”, then press ENTER.
Deleting content added to favorites 1 Press ONLINE MUSIC. 2 Use uio p to select “Favorites”, then press ENTER. 3 Use ui to select the content you want to delete from favorites, then press OPTION. The option menu screen is displayed. 4 Use ui to select “Remove from Favorites”, then press ENTER.
Playing back music and a favorite picture at the same time (Slideshow) n Supported input sources : USB 1 Play back a still picture. 0 Playing back still pictures stored on USB memory devices. ( v p. 83) 2 Play back a music file. ( v p. 83) 3 Press OPTION.
Setting the Slideshow Interval Set the playback interval when playing back a slideshow of still picture (JPEG) files stored on a USB memory device or media server, or on the Flickr website. n Supported input sources : USB / Media Server / Flickr 1 While the list is displayed, press OPTION.
Adjusting the volume of each channel to match the input source (Channel Level Adjust) The volume of each channel can be changed while listening to music. You can set this for each input source. 1 Press OPTION. The option menu screen is displayed. 2 Use ui to select “Channel Level Adjust”, then press ENTER.
Adjusting the tone (Tone) Adjusts the tonal quality of the sound. 1 Press OPTION. The option menu screen is displayed. 2 Use ui to select “Tone”, then press ENTER. The Tone screen is displayed. 3 Use o p to set the tone control function to on/off.
Displaying your desired video during audio playback (Video Select) This unit can display video from a different source on TV during audio playback. You can set this for each input source.
Adjusting the picture quality for your viewing environment (Picture Mode) n Supported input sources : CBL/SAT / DVD / Blu-ray / Game / AUX1 / AUX2 / Media Player / iPod/USB / Online Music / CD z / TV Audio z z You can set the picture mode when an HDMI, component video or video connector is assigned.
Playing the same music in all zones (All Zone Stereo) You can play back the music being played back in MAIN ZONE simultaneously in ZONE2 and ZONE3 (other rooms). It is useful when you want to enjoy the same music at the same time in multiple rooms during home party or when you want to play back the same BGM in the entire house.
Selecting a sound mode . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT GAME GAME CB CB L/ SAT Blu-ray Blu- ray D VD VD AUX1 AUX1 AUX2 AUX2 INTE RNET R ADIO AD.
Selecting a sound mode 1 Press MOVIE, MUSIC or GAME to select a sound mode. MOVIE : Switches to the sound mode suitable for enjoying movies and TV programs. MUSIC : Switches to the sound mode suitable for enjoying music. GAME : Switches to the sound mode suitable for enjoying games.
Direct playback Sound recorded in source is played as is. 1 Press PURE to select “Direct”. Direct playback begins. While DSD signals are played back, “DSD Direct” is displayed. Pure Direct playback This mode is for playback with higher sound quality than in Direct playback mode.
Auto surround playback This mode detects the type of input digital signal, and automatically selects the corresponding mode for playback. Perform stereo playback when the input signal is PCM. When the input signal is Dolby Digital or DTS, the music is played back according to the respective channel number.
o Description of sound mode types Dolby sound mode Sound mode type Description Dolby Surround This mode uses Dolby Surround Upmixer to extend various sources to natural and realistic multi channels for playback. Use ceiling speakers such as top middle speakers to realize a three-dimensional sound field.
DTS sound mode Sound mode type Description DTS Neo:X This matrix decoding technology uses the DTS Neo:X decoder to playback 2-channel source or 5.1/6.1/7.
PCM multi-channel sound mode Sound mode type Description Multi Ch In This mode can be selected when playing multi-channel PCM/DSD sources. Audyssey DSX ® sound mode Sound mode type Description Audyssey DSX ® (A-DSX) z This mode creates playback for the new channels (front wide or front height) in 5.
Original sound mode Sound mode type Description Multi Ch Stereo This mode is for enjoying stereo sound from all speakers. Stereo audio (2-channel) sources are played back via the front (L/R) speakers, the surround speakers and surround back speakers (if connected).
Stereo sound mode Sound mode type Description Stereo This mode plays 2-channel stereo audio with no additional surround sound processing. 0 Sound is output from the front left and right speakers, and subwoofer if connected.
o Sound mode that can be selected for each input signal 0 The following sound modes can be selected using the MOVIE, MUSIC and GAME buttons. 0 Adjust the sound field effect with the menu “Surround Parameter” to enjoy surround sound the way you like it.
Input signal Sound mode Sound mode MOVIE MUSIC GAME Multi-channel z 3 Stereo S S S Dolby Digital Dolby Digital S S S Dolby Digital + Dolby Surround S S S Dolby Digital A-DSX z 4 S S S Dolby Digital + .
Input signal Sound mode Sound mode MOVIE MUSIC GAME Multi-channel z 3 Dolby Digital Plus Dolby Digital Plus S S S Dolby Digital Plus + Dolby Surround z 5 S S S Dolby Atmos z 6 S S S Dolby Digital Plus.
Input signal Sound mode Sound mode MOVIE MUSIC GAME Multi-channel z 3 DTS-HD / DTS Express DTS-HD Hi Res S S S DTS-HD Mstr S S S DTS-HD Mstr A-DSX z 4 S S S DTS Express S S S DTS Express A-DSX z 4 S S.
Input signal Sound mode Sound mode MOVIE MUSIC GAME Multi-channel z 3 Multi Ch Stereo S S S Mono Movie S Rock Arena S Jazz Club S Matrix S Video Game S Virtual S S S z 3 Some sound modes cannot be selected depending on the audio format or number of channels of the input signal.
o Views on the display . Dolby D + S Blu-ray q w A Shows a decoder to be used. 0 In the case of the Dolby Digital Plus decoder, “Dolby D +” is displayed. B Shows a decoder that creates sound output. 0 “ k ” indicates that the Dolby Surround decoder is being used.
HDMI control function A recent addition to the HDMI standard is CEC (Consumer Electronics Control), which allows control signals from one device to communicate with another device via the HDMI cable connection. Setting procedure 1 Enable the HDMI control function of this unit.
Sleep timer function . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ .
Using the sleep timer 1 Press MAIN, Z2 or Z3 to select the operating zone with the remote control. The button for the selected zone is lit. 2 Press SLEEP and display the time you want to set. 0 The B indicator lights up on the display and the sleep timer starts.
Quick select plus function . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SAT Blu-ray Blu- ray.
Calling up the settings 1 Press MAIN, Z2 or Z3 to select the operating zone with the remote control. The button for the selected zone is lit. 2 Press QUICK SELECT. The Quick Select settings registered to the button you pressed are called up. 0 The default settings for the input source and volume are as shown below.
Changing the settings 1 Set the items below to the settings you want to register. The following settings from A to I can be memorized for MAIN ZONE, and settings A and B can be memorized for ZONE2 and ZONE3. A Input source ( v p. 75) B Volume ( v p. 76) C Sound mode ( v p.
Web control function You can control this unit from a web control screen on a web browser. . This unit PC Router Tablet 0 This unit and the PC or tablet need to be connected correctly to the network in order to use the web control function. (“Connecting to a home network (LAN)” ( v p.
4 Enter the IP address of this unit in browser’s address box. For example, if the IP address of this unit is “192.168.100.19”, enter “http://192.168.100.19”. . http://192.168.100.19 File Edit View Tools Help Favorites 5 When the top menu is displayed, click on the menu item you want to operate.
Playback in ZONE2/ZONE3 (Separate room) You can operate this unit to enjoy video and audio in a room (ZONE2 and ZONE3) that is different from the room where this unit is placed (MAIN ZONE). You can simultaneously play back the same source in both the MAIN ZONE, ZONE2 and ZONE3.
o Connection 2 : Connection through the video output connector and speaker output connector When “Assign Mode” in the menu is set to any of the following audio is output from speakers in ZONE2 or ZONE3.
n Assign Mode: 7.1ch + ZONE2/3-MONO . IN VIDEO VIDEO COMPONENT VIDEO YP B P R IN wq w q ASSIGNABLE SPEAKERS SURROUND BACK SURROUND BACK FRON T ZONE3 ZONE2 or This unit MAIN ZONE COMPONENT VIDEO MONITO.
o Connection 3 : Connection through the video output connector and external power amplifiers The audio signals of this unit’s ZONE2 and ZONE3 audio output connectors are played on the ZONE2 and ZONE3 power amplifiers.
0 The analog audio signal and the 2-channel PCM signal input from HDMI connector or digital connectors (OPTICAL/COAXIAL) can be played back in ZONE2. 0 If you want to play back HDMI signals other than 2-channel PCM in ZONE2, set “HDMI Audio” to “PCM”.
Playback in ZONE2/ZONE3 . SOUND MODE SOUN D MOD E AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT TUNE TUNE TUNE TUNE PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C OPTION OPTI ON INFO INFO BACK.
o Adjusting the volume Use VOLUME df to adjust the volume. 0 At time of purchase, “Volume Limit” is set to “70 (–10 dB)”. ( v p. 241) Turn MASTER VOLUME after pressing ZONE2 SOURCE or ZONE3 SOURCE on the main unit to adjust the volume. o Turning off the sound temporarily (Muting) Press MUTE : .
Menu map When using menu operations, connect this unit to a TV and operate this unit while viewing the TV. The recommended settings are configured for this unit by default. You can customize this unit based on your existing system and your preferences.
Setting items Detailed items Description Page . Inputs Input Assign Changes input connector assignment. 190 Source Rename Changes the display name for input source. 192 Hide Sources Removes from the display input sources that are not used. 192 Source Level Adjusts the playback level of the audio input.
Setting items Detailed items Description Page . General Language Changes the language of the display on the TV screen. 238 ECO Configures the ECO Mode and Auto Standby energy-saving functions. 238 ZONE2 Setup/ ZONE3 Setup Makes settings for audio playback with ZONE2 and ZONE3.
. SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C GAME GAME CB CB L/ SAT Blu-ray Blu- ray D VD VD AUX1 AUX1 AU.
Inputting characters 0 On this unit, you can change the name displayed on the following screens to the names that you prefer. 0 Preset Name ( v p. 98) 0 Text Search ( v p. 120) 0 Source Rename ( v p. 192) 0 Friendly Name ( v p. 236) 0 Zone Rename ( v p.
Using the keyboard screen 1 Display the screen for inputting characters. G Example H “Source Rename” screen . Inputs/Source Rename Changes the display name for this source CBL/SAT A N 0 $ B O 1 % .
Audio Make audio-related settings. Subwoofer Level Adjust This setting adjusts the volume level for the subwoofer. o Subwoofer Level Adjust Set whether to adjust the subwoofer level. On: Enables the adjustment of the subwoofer level. Off (Default) : Disables the adjustment of the subwoofer level.
o Loudness Management This sets whether to output as specified in “Dynamic Compression” or output directly without compressing the dynamic range of audio recorded in the disc. On (Default) : Outputs are given based on enabling the settings made in “Dynamic Compression” and “Dialog normalization function” ( v p.
o Center Gain Distributes the dialogue output from the center channel to the front left and right channels and widens the sound image in the front. 0.0 – 1.0 0 You can set this when the sound mode is set to DTS Neo:X. 0 The smaller the value, the more dialogue is concentrated on the center channel.
o Room Size Determine size of acoustic environment. Small: Simulate acoustics of a small room. Medium small: Simulate acoustics of a medium-small room. Medium (Default) : Simulate acoustics of a medium room. Medium large: Simulate acoustics of a medium-large room.
o Speaker Select Makes settings for the speakers outputting sound. n When the sound mode is “DTS Neo:X”. Surround Back: Sound is output from the surround back speakers. Height: Sound is output from the front height speakers. Wide: Sound is output from the front wide speakers.
Restorer Compressed audio formats such as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the amount of data by eliminating signal components that are hard for the human ear to hear.
Audio Delay Compensates for incorrect timing between video and audio. 0 ms – 200 ms (Default : 0 ms) 0 Audio Delay for game mode can be set when “Video Mode” is set to “Auto” or “Game”. ( v p. 183) 0 “Audio Delay” settings are stored for each input source.
Audyssey Set Audyssey MultEQ ® XT32, Audyssey Dynamic EQ ® , Audyssey Dynamic Volume ® and Audyssey LFC™. These can be selected after Audyssey ® Setup has been performed. For additional information on Audyssey technology, please see “Explanation of terms” ( v p.
o Dynamic EQ Solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Works with MultEQ ® XT32. On (Default) : Use Dynamic EQ. Off: Do not use Dynamic EQ. When the menu “Dynamic EQ” setting is “On”, it is not possible to do “Tone Control” adjustment.
o Dynamic Volume Solves the problem of large variations in volume level between TV, movies and other content (between quiet passages and loud passages, etc.) by automatically adjusting to the user’s preferred volume setting. Heavy: Most adjustment to softest and loudest sounds.
o Audyssey DSX ® Provides more immersive surround sound by adding the new channels. Wide: Turn on Audyssey DSX ® processing for front wide channel expansion. Height: Turn on Audyssey DSX ® processing for front height channel expansion. Wides/Heights: Turns on Audyssey DSX ® processing for front wide and front height channel expansion.
Graphic EQ Uses the graphic equalizer to adjust the tone of each speaker. 0 Speakers for which “Graphic EQ” can be set differ according to the sound mode. 0 This can be set when the “MultEQ ® XT32” is set to “Off”. ( v p. 171) 0 This cannot be set when the sound mode is set to “Direct” or “Pure Direct”.
o Curve Copy Copy the Flat correction curve created in the Audyssey ® Setup. “Curve Copy” is displayed after Audyssey ® Setup has been performed.
Video Make video-related settings. Picture Adjust Picture quality can be adjusted. 0 Can be set when the “Video Conversion” setting is “On”. ( v p. 184) 0 Can be set when “HDMI”, “COMP” or “VIDEO” is assigned for each input source.
0 The two special adjustment modes, ISF Day and ISF Night, should be used by a certified technician to adjust the color calibration to match the installation conditions. We recommend that the settings and adjustments be carried out by an ISF- certified technician.
o Noise Reduction Reduce overall video noise. Low / Medium / High / Off (Default : Off) o Enhancer Emphasize picture sharpness. 0 – +12 (Default : 0) HDMI Setup Make settings for HDMI video/audio output. NOTE When “HDMI Pass Through” and “HDMI Control” is set to “On”, it consumes more standby power.
o HDMI Audio Out Select HDMI audio output device. AVR (Default) : Play back through speakers connected to the unit. TV: Play back through TV connected to the unit. 0 When the HDMI control function is activated, priority is given to the TV audio setting.
o HDMI Pass Through Selects how this unit will transmit HDMI signals to the HDMI output in standby power mode. On: Transmits the selected HDMI input through the AV receiver’s HDMI output when this unit is in standby power mode. Off (Default) : No HDMI signals are transmitted through this unit’s HDMI output in standby power mode.
o Pass Through Source Sets the HDMI connector that inputs HDMI signals when in standby. Last (Default) : The most recently used input source will go into standby mode. CBL/SAT / DVD / Blu-ray / Game / AUX1 / AUX2 / Media Player / CD z : Pass through the selected input source.
Output Settings Makes settings for video output. 0 Can be set when “HDMI”, “COMP” or “VIDEO” ( v p. 191) is assigned for each input source. 0 “Resolution”, “Progressive Mode” and “Aspect Ratio” can be set when “i/p Scaler” is set to anything other than “Off”.
o Video Conversion The input video signal is converted automatically in conjunction with the connected TV. (“Video conversion function” ( v p. 281)) On (Default) : The input video signal is converted. Off: The input video signal is not converted. o i/p Scaler Set the video input signal to be subjected to i/p scaler processing.
n When the input source is set to “iPod/USB” and “Online Music” On (Default) : Use i/p scaler function. Off: Do not use i/p scaler function. 0 “Analog & HDMI” can be set for input sources for which an HDMI input connector is assigned. 0 Which items can be set depend on the input source assigned to each input connector.
o Progressive Mode Set an appropriate progressive conversion mode for the source video signal. Auto (Default) : The video signal is automatically detected and the appropriate mode is set. Video: Select mode suitable for video playback. Video and Film: Select mode suitable for video and 30- frame film material playback.
Component Video Out Set the zone to which the component video output connector is assigned. MAIN ZONE (Default) : Assigns the component video output connector to MAIN ZONE.
On Screen Display Select the on-screen display user interface preferences. o Volume Sets where to display the volume level. Bottom (Default) : Display at the bottom.
TV Format Set the video signal format to be output for the TV you are using. o Format PAL (Default) : Select PAL output. NTSC: Select NTSC output. “Format” can also be set by the following procedure. However, the menu screen is not displayed. Following the display content to make the setting.
Inputs Perform settings related to input source playback. You do not have to change the settings to use the unit. Make settings when needed. Input Assign By making connections as indicated by the inpu.
o HDMI Set this to change the HDMI input connectors assigned to the input sources. 1 / 2 / 3 / 4 / 5 / 6 / 7 / Front: Assign an HDMI input connector to the selected input source. – : Do not assign an HDMI input connector to the selected input source.
Source Rename Change the display name for input source. This is convenient when the name of your device and the input source name of this unit are different. You can change the name to suit your needs. When the renaming is completed, the name is displayed on this unit’s display and on the menu screen.
Input Select Set the audio input mode and decode mode of each input source. The input modes available for selection may vary depending on the input source. “Input Select” settings are stored for each input source. o Input Mode Set the audio input modes for the different input sources.
Speakers The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically. This is called “Audyssey ® Setup”. You do not have to perform Audyssey ® Setup when you have already performed “Speaker Calibration” in “Setup Assistant”.
o About the main listening position The main listening position is the position where listeners would normally sit or where one would normally sit alone within the listening environment. Before starting Audyssey ® Setup, place the Sound calibration microphone in the main listening position.
Procedure for speaker settings (Audyssey ® Setup) . Finish Check Calculation & Store Measurement Preparation 1 Attach the Sound calibration microphone to the supplied microphone stand or own tripod and install it at the main listening position.
3 Connect the Sound calibration microphone to the SETUP MIC jack of this unit. . When the Sound calibration microphone is connected, the follo wing screen is display ed.
6 When the following screen is displayed, select “Begin Test” and then press ENTER. Start the measurement of the first position. . Begin Test Back Select “Begin Test” to start the calibration. NOTE: You will hear a series of loud chirps starting and stopping during the tests.
8 Move the Sound calibration microphone to position 2, select “Continue”, then press ENTER. The measurement of the second position starts. Measurements can be made in up to eight positions.
11 Perform the settings for Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . The following screen is displayed during the analysis. Configure the settings as preferred. . Audyssey Setup Audyssey Dynamic EQ maintains bass, clarity and surround sound at low volumes letting you enjoy late-night movies and television.
13 Select “Details” and press ENTER to verify the measurement results. 0 Subwoofers may measure a greater reported distance than the actual distance due to added electrical delay common in subwoofers. NOTE Do not change the speaker connection or subwoofer volume after Audyssey ® Setup.
Error messages An error message is displayed if Audyssey ® Setup could not be completed due to speaker placement, the measurement environment, etc. If an error message is displayed, check the relevant items and perform the necessary measures. Be sure to turn off the power before checking speaker connections.
o Subwoofer level error message and how to adjust The optimal level of each subwoofer channel for Audyssey ® Setup measurement is 75 dB. During subwoofer level measurement, an error message is displayed when one level of subwoofers is outside the 72 – 78 dB range.
Retrieving Audyssey ® Setup settings If you set “Restore...” to “Restore”, you can return to Audyssey ® Setup measurement result (value calculated at the start by MultEQ ® XT32) even when you have changed each setting manually. . Audyssey Setup Channel Select Amp Assign Check Results Restore.
Manual Setup Perform when setting the speakers manually or when changing settings made in Audyssey ® Setup. 0 If you change the speaker settings after performing Audyssey ® Setup, you will no longer be able to select Audyssey MultEQ ® XT32, Audyssey Dynamic EQ ® or Audyssey Dynamic Volume ® .
7.1ch + ZONE2: 0 Setting to assign the power amplifiers in this unit for ZONE2 to 2-channels. 0 You can connect speakers for up to 9.1 channels for MAIN ZONE. Speakers to output audio are automatically switched for playing back up to 7.1-channels in accordance with the input signal and sound mode.
9.1ch/ 2ch Front: 0 Setting to assign the power amplifiers in this unit for connecting 2-channel playback speakers to 2 channels. 0 You can switch the front speakers when using 2-channel playback in direct mode or stereo mode, or when using multi-channel surround playback.
o Detailed settings when “Assign Mode” is set to “11.1ch” When “Assign Mode” is set to “11.1ch”, set the following items. n Height Speakers Select the number of the height speakers used in MAIN ZONE. 2 Height Speakers (Default) : Uses a set of (two) height speakers.
G When “Height Speakers” is set to “Using Dolby Speakers” H Select the height channels used for the two pair. AUDIO OUT connectors Select items HEIGHT1 HEIGHT2 Front Dolby (Default) Front Dolby Not assigned. Surround Dolby Surround Dolby Not assigned.
n Pre-out Selects the PRE OUT connectors that connect the external power amplifier used in MAIN ZONE. G When “Height Speakers” is set to “2 Height Speakers” H Front: The front left and right pre-amp outputs are connected to an external amplifier.
G When “Height Speakers” is set to “Using Dolby Speakers” H Available settings differ depending on the “Height Layout” and “Wide/ Height2” settings. Front: The front left and right pre-amp outputs are connected to an external amplifier.
n Height Layout Select the type of the height speakers used. This can be selected when the “Height Speakers” setting is “2 Height Speakers”, “4 Height Speakers” or “Using Dolby Speakers”. G When “Height Speakers” is set to “2 Height Speakers” H Select the height channel used.
o Detailed settings when “Assign Mode” is set to “7.1ch + ZONE2” When “Assign Mode” is set to “7.1ch + ZONE2”, set the following items. n Speakers for ZONE2 Select speaker terminals that output audio in ZONE2. The channels of speaker terminals selected for ZONE2 cannot be output in MAIN ZONE.
o Detailed settings when “Assign Mode” is set to “7.1ch + ZONE3” When “Assign Mode” is set to “7.1ch + ZONE3”, set the following items. n Speakers for ZONE3 Select speaker terminals that output audio in ZONE3. The channels of speaker terminals selected for ZONE3 cannot be output in MAIN ZONE.
o Detailed settings when “Assign Mode” is set to “7.1ch + ZONE2/3-MONO” When “Assign Mode” is set to “7.1ch + ZONE2/3-MONO”, set the following items. n Speakers for ZONE2/3 Select speaker terminals that output audio in ZONE2 and ZONE3.
o Detailed settings when “Assign Mode” is set to “7.1ch (Bi-Amp)” When “Assign Mode” is set to “7.1ch (Bi-Amp)”, set the following items. n Speakers for Bi-Amp Select the speaker terminals used for the bi-amp connection of front speakers.
o Detailed settings when “Assign Mode” is set to “9.1ch/2ch Front” When “Assign Mode” is set to “9.1ch/2ch Front”, set the following items. n Speakers for 2ch Select the speaker terminals that connect the front speakers exclusively used for 2-channel playback.
o Detailed settings when “Assign Mode” is set to “7.1ch + Front B” When “Assign Mode” is set to “7.1ch + Front B”, set the following items. n Speakers for Front B Select the speaker terminals used for the front speakers of the second unit.
o Detailed settings when “Assign Mode” is set to “Dolby Atmos” When “Assign Mode” is set to “Dolby Atmos”, set the following items. n Layout Select the speaker layout for Dolby Atmos playback. 7.1ch + 4 Height: This is a layout that adds the top front and top rear speakers to the 7.
Speaker Config. Select whether or not speakers are present, playback capacity for low bass frequencies and speaker size. o Front Set the front speaker size. Large (Default) : Use a large speaker that can adequately play back very low bass frequencies.
o Surr. Back Set the presence, size and number of surround back speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default) : Use a small speaker that has inadequate playback capacity for very low bass frequencies.
o Top Front Set the presence and size of the top front speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default) : Use a small speaker that has inadequate playback capacity for very low bass frequencies.
o Front Dolby Set the presence and size of the front Dolby speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default) : Use a small speaker that has inadequate playback capacity for very low bass frequencies.
Distances Set distance from listening position to speakers. Measure beforehand the distance from the listening position to each speaker. o Unit Set the unit of distance. Meters (Default) Feet o Step Set the minimum variable width of the distance. 0.1 m (Default) / 0.
Levels Set the volume of the test tone to be the same at the listening position when it is output from each speaker. o Test Tone Start A test tone is output from the selected speaker. While listening to the test tone, adjust the volume output from the selected speaker.
Crossovers Set in accordance with the lower limit frequency of the base frequencies that can be played back through each speaker. See the speaker manual for information concerning speaker crossover frequency. o Speaker Selection Selects how to set the crossover frequency.
Bass Set subwoofer and LFE signal range playback. o Subwoofer Mode Select low range signals to be reproduced by subwoofer. LFE (Default) : The low range signal of the channel set to “Small” speaker size is added to the LFE signal output from the subwoofer.
Front Speaker Set the front speaker A/B to use for every sound mode. A (Default) : Front speaker A is used. B : Front speaker B is used. A+B : Both front speakers A and B are used. This can be set when “Assign Mode” is set to “7.1ch + Front B”.
o Front Set the size of the front speakers for 2-channel playback. Large (Default) : Use a large speaker that can adequately play back very low bass frequencies. Small: Use a small speaker that has inadequate playback capacity for very low bass frequencies.
o Crossover Set the maximum frequency of the bass signal output from each channel to the subwoofer. 40 Hz / 60 Hz / 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 200 Hz / 250 Hz (Default : 80 Hz) 0 This can be set when “2ch Playback”-“Subwoofer” is set to “Yes”.
Network To use this unit by connecting it to a home network (LAN), you must configure network settings. If you set up your home network (LAN) via DHCP, set “DHCP” to “On”. (Use the default setting.) This allows this unit to use your home network (LAN).
Wi-Fi Setup Connect to a wireless LAN (Wi-Fi) router. The router can be connected in the following ways. Select the connection method to suit your home environment. o Scan Networks Select the network you wish to connect to from the list of possible networks shown on the TV screen.
o WPS Router Use a WPS-compatible router to connect. There are two ways to connect, using the push button method or the PIN code method. Select the connection method to match your router. n When connecting using the push button method 1. Select “Push Button” on the TV screen.
Settings Configure the proxy settings and IP address. 0 If you are using a broadband router (DHCP function), the information required for network connection such as the IP address will be automatically configured since the DHCP function is set to “On” in the default settings of this unit.
o Proxy Make this setting when connecting to the Internet via a proxy server. Make the proxy settings only when you connect to the Internet via a proxy server that is on your internal network or provided by your provider, etc. On(Address): Select when inputting by address.
Friendly Name The Friendly Name is the name of this unit displayed on the network. You can change the Friendly Name according to your preferences. o Friendly Name Selects Friendly Name from the list. When you select “Other”, you can change the Friendly Name according to your preferences.
Maintenance Mode Use when receiving maintenance from a Denon service engineer or custom installer. Ordinarily, this mode isn’t suitable for use by the end user, only by a trained service technician or custom installation professional. NOTE Only use this function if so instructed by a Denon serviceperson or installer.
General Make various other settings. Language Set the language for display the menu on the TV screen. English / Deutsch / Français / Italiano / Español / Nederlands / Svenska / Pусский / Polski (Default : English) “Language” can also be set up by the following operation.
o Power On Default Set the mode to ECO when the power is on. Last (Default) : The ECO Mode will be set to the previous setting before the power was switched off. On: When power is turned on, the mode will always be switched to the ECO Mode in “On”.
ZONE2 Setup / ZONE3 Setup Makes settings for audio playback with ZONE2 and ZONE3. Values set for “Volume Limit” and “Power On Volume” are displayed according to the setting specified for the volume “Scale”. ( v p. 170) o Bass Adjust bass. -10 dB – +10 dB (Default : 0 dB) o Treble Adjust treble.
o Volume Level Set the volume output level. Variable (Default) : Volume can be adjusted. 1 – 98 (–79.5 dB – 18.0 dB): Volume is fixed at the desired level. The volume cannot be adjusting using the remote control unit. o Volume Limit Make a setting for maximum volume.
Zone Rename Change the display title of each zone to one you prefer. MAIN ZONE / ZONE2 / ZONE3 Set Defaults: The default setting is restored for the edited zone name. Up to 10 characters can be input. For character input, see “Using the keyboard screen” ( v p.
Front Display Makes settings related to the display on this unit. o Dimmer Adjust the display brightness of this unit. Bright (Default) : Normal display brightness. Dim: Reduced display brightness. Dark: Very low display brightness. Off: Turns the display off.
o Video Show the HDMI input/output signals and HDMI monitor information for MAIN ZONE. HDMI Signal Info. Resolution / Color Space / Pixel Depth HDMI Monitor 1 / HDMI Monitor 2 Interface / Resolutions o ZONE Show information about current settings. MAIN ZONE: This item shows information about settings for MAIN ZONE.
Usage Data To help us improve our products and customer service, Denon collects anonymous information about how you use your AV receiver (such as frequently used input sources and sound modes and speaker settings). Denon will never provide any information we collect to third parties.
Firmware Checks for the latest firmware information about updates and upgrades, updates the firmware, and sets up the notification message display for updates and upgrades. o Update Updates the firmware of this unit. Check for Update: Checks to see if the firmware is the latest version.
o Add New Feature Display new features that can be downloaded to this unit and perform an upgrade. Upgrade Package: Display the items to be upgraded. Upgrade Status: Display a list of the additional functions provided by the upgrade. Upgrade Start: Execute the upgrade process.
Setup Lock Protect settings from inadvertent changes. o Lock On: Turn protection on. Off (Default) : Turn protection off. When cancelling the setting, set “Lock” to “Off”. NOTE When “Lock” is set to “On”, no setting items are displayed except for “Setup Lock”.
Operating external devices with the remote control unit . SOUND MODE SOUN D MOD E POWER POWE R AVR CONTROL AVR CON TROL QUICK SELECT QUICK SELECT PURE PU RE MOVIE MO VI E GAME GA ME MUSIC MU SI C INTE.
Registering preset codes There are two methods for registering preset codes; the simple method for registering preset codes of Denon players, and the method for registering the preset numbers of other manufacturers’ devices. ● “Registering Denon Players”( v p.
n Registering multiple players at the same time 1 Press and hold down QUICK SELECT 1 – 4 and OPTION until the DEV, TV and AVR indicators on the remote are flashing green, then release.
Operating devices To operate an external device, press the input source button registered with the preset code, followed by one of the buttons in the following tables. 0 The “DEV.” indicator lights when an external device is being operated. 0 The “TV” indicator lights when the TV is being operated.
n TV group (TV) operation Operation buttons Function TV X TV power on/off TV INPUT Switch TV input TV MENU TV menu CH/PAGE df Switch channels (up/down) INFO Information OPTION Sub menu, Option u i o p.
n BD/DVD group (Blu-ray Disc player/HD-DVD player/DVD player/DVD recorder) operation Operation buttons Function DEVICE X Power on/off DEVICE MENU (Popup) Menu CH/PAGE df Switch channels (up/down) INFO.
Initializing registered preset codes 1 Press and hold down MAIN and OPTION until the DEV, TV and AVR indicators on the remote are flashing green, then release. Specifying the operating zone with the remote control To prevent accidental misuse, you can set the zone for which the remote control unit is used.
o Contents Tips I want the volume not to become too loud by mistake 257 I want to keep the volume at the same level when I turn the power on 257 I want to have the subwoofer always output audio 257 I .
Tips I want the volume not to become too loud by mistake 0 Set the volume upper limit for “Volume Limit” in the menu beforehand. This prevents children or others from increasing the volume too much by mistake. You can set this for each zone. ( v p.
I want to set the optimized listening environment after changing the configuration/position of the speakers or changing a speaker to a new one. 0 Perform Audyssey ® Setup. This automatically makes the optimized speaker settings for the new listening environment.
Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other devices operating properly? If this unit does not operate properly, check the corresponding symptoms in this section.
o Power does not turn on / Power is turned off Symptom Cause / Solution Page Power does not turn on. 0 Check whether the power plug is correctly inserted into the power outlet. 73 Power automatically turns off. 0 The sleep timer is set. Turn on the power again.
o Operations cannot be performed through the remote control unit Symptom Cause / Solution Page Operations cannot be performed through the remote control unit. 0 Batteries are worn out. Replace with new batteries. 9 0 Operate the remote control unit within a distance of about 7 m from this unit and at an angle of within 30°.
o No sound comes out Symptom Cause / Solution Page No sound comes out of speakers. 0 Check the connections for all devices. 35 0 Insert connection cables all the way in. － 0 Check that input connectors and output connectors are not reversely connected.
o Desired sound does not come out Symptom Cause / Solution Page The volume does not increase. 0 The maximum volume is set too low. Set the maximum volume using “Limit” on the menu. 170 0 Appropriate volume correction processing is performed according to the input audio format and settings, so the volume may not reach the upper limit.
Symptom Cause / Solution Page DTS Neo:X mode cannot be selected. 0 It cannot be selected when “Speaker Config.” - “Surround” is set for “None”. 220 0 DTS Neo:X cannot be selected when using the headphones. － Dolby Surround mode cannot be selected.
o Sound is interrupted or noise occurs Symptom Cause / Solution Page During playback from the Internet radio or USB memory device, sound is occasionally interrupted. 0 When the transfer speed of the USB memory device is slow, sound may occasionally be interrupted.
o No video is shown on the TV Symptom Cause / Solution Page No picture appears. 0 Check the connections for all devices. 56 0 Insert connection cables all the way in. － 0 Check that input connectors and output connectors are not reversely connected.
Symptom Cause / Solution Page When using HDMI ZONE2, the video output in MAIN ZONE is interrupted. 0 When ZONE2 is operated with the same input source selected for MAIN ZONE and ZONE2, video in MAIN ZONE may be interrupted.
o The menu screen is not displayed on the TV Symptom Cause / Solution Page The menu screen or status information screen is not displayed on the TV. 0 The menu screen is only displayed on this unit and a TV connected with an HDMI cable.
o iPod cannot be played back Symptom Cause / Solution Page iPod cannot be connected. 0 When using iPod by connecting it to the USB port, some iPod variations are not supported. 65 0 When iPod is connected by using a USB cable other than the genuine cable, iPod may not be recognized.
o USB memory devices cannot be played back Symptom Cause / Solution Page “No connection” is displayed. 0 This unit cannot recognize the USB memory device. Disconnect and reconnect the USB memory device. 65 0 Mass storage class compatible USB memory devices are supported.
o File names on the iPod/USB memory device are not displayed properly Symptom Cause / Solution Page The file names are not displayed properly (“...”, etc.). 0 Characters that cannot be displayed have been used. On this unit, characters that cannot be displayed are replaced with a “.
o The Internet radio cannot be played back Symptom Cause / Solution Page A list of broadcasting stations is not displayed. 0 The LAN cable is not properly connected, or the network is disconnected. Check the connection status. 69 0 Perform the network diagnostic mode.
o Music files on PC or NAS cannot be played back Symptom Cause / Solution Page Files stored on a computer cannot be played. 0 Files are stored in a non-compatible format. Record in a compatible format. 285 0 Files that are copyright protected cannot be played on this unit.
o The HDMI control function does not work Symptom Cause / Solution Page The HDMI control function does not work. 0 Check that “HDMI Control” in the menu is set to “On”. 181 0 You cannot operate devices that are not compatible with the HDMI control function.
o Cannot connect to a wireless LAN network Symptom Cause / Solution Page Cannot connect to the network. 0 The network name (SSID), password and encryption setting have not been set up correctly. Configure the network settings according to the setting details of this unit.
o When using HDMI ZONE2, the devices does not function properly Symptom Cause / Solution Page When using MAIN ZONE, video output is interrupted in HDMI ZONE2. 0 With the same input source selected for MAIN ZONE and ZONE2, when you operate MAIN ZONE, video may be interrupted in HDMI ZONE2.
Resetting factory settings Perform this procedure if the display is abnormal or if operations cannot be performed. Various settings are reset to the factory default values. Make settings again. . X BACK INFO 1 Turn off the power using X . 2 Press X while simultaneously pressing INFO and BACK.
About HDMI HDMI is an abbreviation of High-Definition Multimedia Interface, which is an AV digital interface that can be connected to a TV or amplifier.
0 Auto Lip Sync This function can automatically correct delay between the audio and video. Use a TV that is compatible with the Auto Lip Sync function. 0 HDMI Pass Through Even when the power to this unit is set to standby, signals input from the HDMI input connector are output to a TV or other device that is connected to the HDMI output connector.
o Supported audio formats 2-channel Linear PCM 2-channel, 32 kHz – 192 kHz, 16/20/24 bit Multi-channel Linear PCM 7.1-channel, 32 kHz – 192 kHz, 16/20/24 bit Bitstream Dolby Digital / DTS / Dolby Atmos / Dolby TrueHD / Dolby Digital Plus / DTS-HD Master Audio / DTS-HD High Resolution Audio / DTS Express DSD 2-channel – 5.
Video conversion function This unit automatically converts the input video signals as shown in the diagram before outputting them to the TV. The main zone video conversion function is compatible with the following formats: NTSC, PAL, SECAM, NTSC4.43, PAL-N, PAL-M and PAL-60.
This unit can convert the input video signals to the resolution that is set for “Resolution” in the menu before outputting them to the TV. ( v p. 185) Output signal Input signal HDMI 480i/576i 480.
Playing back a USB memory devices 0 This unit is compatible with MP3 ID3-Tag (Ver. 2) standard. 0 This unit can show the artwork that was embedded by using MP3 ID3-Tag Ver.
o Maximum number of playable files and folder The limits on the number of folders and files that can be displayed by this unit are as follows. Media Item USB memory device Memory capacity FAT16 : 2 GB.
Playing back a file saved on a PC or NAS 0 This unit is compatible with MP3 ID3-Tag (Ver. 2) standard. 0 This unit can show the artwork that was embedded by using MP3 ID3-Tag Ver.
Playing back Internet Radio o Playable broadcast station specifications Sampling frequency Bit rate Extension WMA 32/44.1/48 kHz 48 – 192 kbps .wma MP3 32/44.
Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels.
z 1 The applicable sound mode includes “Dolby Surround” and sound modes that have “+Dolby Surround” in the sound mode name. z 2 The applicable sound mode includes “DTS Neo:X” and sound modes that have “+Neo:X” in the sound mode name. z 3 A signal for each channel contained in an input signal is output as audio.
Sound modes and surround parameters . Sound mode Surround Parameter Subwoofer Level Adjust Cinema EQ Loudness Management z 1 Dynamic Compression z 2 Low Frequency Effects z 3 Delay Time Effect Level R.
. Sound mode Surround Parameter Dialog Enhancer Tone z 6 Audyssey Restorer z 9 Center Spread Center Gain MultEQ ® XT32 z 7 Dunamic EQ z 8 Dunamic Volume z 8 Audyssey LFC TM z 8 Audyssey DSX ® Direct.
z 1 This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played back. z 2 This item can be selected when the Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos or DTS is played back. z 3 This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. . Sound mode NOTE 2-channel signal Multi-channel signal Analog / PCM Dolby Digital (+/HD) DTS (-HD) DSD (Super Audio CD) PCM Multi DTS-HD DTS Express DTS ES Dscrt6.
. Sound mode NOTE 2-channel signal Multi-channel signal Analog / PCM Dolby Digital (+/HD) DTS (-HD) DSD (Super Audio CD) PCM Multi DTS-HD DTS Express DTS ES Dscrt6.
z 1 This item can be selected when surround back speakers are used. z 2 The “Cinema” mode, “Music” mode or “Game” mode can be selected. This item can be selected when using any of the surround back, front height or front wide speaker. z 3 This item can be selected when the input signal is DTS-HD Master Audio.
Explanation of terms o Audyssey Audyssey Dynamic EQ ® Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ ® works in tandem with Audyssey MultEQ ® XT32 to provide well-balanced sound for every listener at any volume level.
Audyssey Dynamic Volume ® Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies.
Dolby Digital Dolby Digital is a multi-channel digital signal format developed by Dolby Laboratories. A total of 5.1-channels are played: 3 front channels (“FL”, “FR” and “C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for low frequency effects.
Dolby TrueHD Dolby TrueHD is a high definition audio technology developed by Dolby Laboratories, using lossless coding technology to faithfully reproduce the sound of the studio master.
DTS-ES™ Discrete 6.1 DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format adding a surround back (SB) channel to the DTS digital surround sound. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder.
o Audio ALAC (Apple Lossless Audio Codec) This is a codec for lossless audio compression method developed by Apple Inc. This codec can be played back on iTunes, iPod or iPhone. Data compressed to approximately 60 – 70 % can be decompressed to exactly the same original data.
MPEG (Moving Picture Experts Group), MPEG-2, MPEG-4 These are the names for digital compression format standards used for the encoding of video and audio. Video standards include “MPEG-1 Video”, “MPEG-2 Video”, “MPEG-4 Visual”, “MPEG-4 AVC”.
o Video ISF ISF (Imaging Science Foundation) is an organization that certifies video technicians who are then qualified to carry out calibration and adjustment to match the installation conditions. It also sets quality standards for the optimization of device video performance.
TKIP (Temporal Key Integrity Protocol) This is a network key used for WPA. The encryption algorithm is RC4, the same as for WEP, but the security level is increased by changing the network key used for encryption for each packet. vTuner This is a free online content server for Internet Radio.
Network Names (SSID: Security Set Identifier) When forming wireless LAN networks, groups are formed to prevent interference, data theft, etc. These groups are based on “SSID (network names)”. For enhanced security, a WEP key is set so that communication is unavailable unless both the “SSID” and the WEP key match.
o Others App Store App Store is a site that sells application software for such devices as the iPhone or iPod Touch, and is operated by Apple Inc. Denon Link HD Denon Link HD uses the clock of the AV amplifier connected by Denon Link HD to achieve HDMI signal transfer with low jitter.
Trademark information . “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS-HD Master Audio and DTS Neo:X | 11.1 are a trademark of DTS, Inc.
Specifications o Audio section 0 Power amplifier Rated output: Front: 140 W + 140 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.05 % T.H.D.) 175 W + 175 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Center: 140 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.05 % T.H.D.) 175 W (6 Ω/ohms, 1 kHz with 0.
0 Analog Input sensitivity/Input impedance: 200 mV/47 kΩ/kohms Frequency response: 10 Hz – 100 kHz — +1, –3 dB (Direct mode) S/N: 102 dB (IHF–A weighted, Direct mode) Distortion: 0.005 % (20 Hz – 20 kHz) (Direct mode) Rated output: 1.2 V 0 Digital D/A output: Rated output — 2 V (at 0 dB playback) Total harmonic distortion — 0.
o Video section 0 Standard video connectors Input/output level and impedance: 1 Vp-p, 75 Ω/ohms Frequency response: 5 Hz – 10 MHz — 0, –3 dB 0 Color component video connector Input/output level and impedance: Y signal — 1 Vp-p, 75 Ω/ohms P B / C B signal — 0.
o Wireless LAN section Network type (wireless LAN standard): Conforming to Wi-Fi ® z 1 Security: WEP 64 bit, WEP 128 bit WPA/WPA2-PSK (AES) WPA/WPA2-PSK (TKIP) Radio frequency: 2.4 GHz No. of channels: 1 – 13 ch z 1 The Wi-Fi ® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.
o Bluetooth section Communications system: Bluetooth Version 2.1 + EDR (Enhanced Data Rate) Transmission power: Maximum 2.5 mW (Class 2) Maximum communication range: Approx.
o Dimensions (Unit : mm) . 434 237 55 70 15 152 167 235 339 393 22 12 32 344 60 45 45 o Weight: 14.1 kg Contents Connections Playback Settings Tips Appendix 313 Front panel Display Rear panel Remote I.
Index v Numerics 11.1-channel ............................................ 43, 52 3D ................................................................ 278 4K ................................................................ 278 5.1-channel .............
v I Input Assign ................................................. 190 Input signal ................................................... 292 Input source settings ............................ 159, 190 Inputting characters ..............................
v T Text Search .................................................. 120 Tips .............................................................. 257 Tone Control ................................................ 124 Troubleshooting ..........................
List of preset codes To return a preset code to the default settings, register the AVR code “73347” to the button whose preset code you want to cancel.
CBL/SAT group Registrable input source button : . S Samsung 01877 Scientific Atlanta 01877 Shaw 01376 Suddenlink 01376, 01877 T T ime Warner 01376, 01877 V Videotron 01877 VTR 01376 W WideOpenWest 01.
CBL/SAT group Registrable input source button : . J JVC 00775 K KabelBW 01195, 01915 Koenig 01631 L Lava 01631 Linsar 01284 Lodos 01284 Logik 01284 M Matsui 01284 MegaSat 01631 Metronic 01631 Motorola.
CBL/SAT group Registrable input source button : . CBL/SA T/PVR Combination C Com Hem 01176 F Foxtel 01356 H Humax 01176 P Pace 01356 T T echniSat 01195 SA T/PVR Combination A Amstrad 01175 B Bell Expr.
TV group Registrable input source button : . TV A A.R. Systems 10556 Acoustic Solutions 11037 AEG 11037 Akai 10556 Akura 11037 Alba 11037 Alien 11037 Amstrad 11037 AOC 10625 Aristona 10556 ART 11037 B.
TV group Registrable input source button : . Multitec 11037 Myryad 10556 N Neckermann 10556 NEI 11037 Neufunk 10556 New T ech 10556 O O.K.Line 11037 Orion 10556, 11037 Ormond 11037 Osaki 10556 Otto V .
TV group Registrable input source button : . TV/DVD Combination B Black Diamond 11037 Blue Sky 11037 Bush 11037 C Centrum 11037 Crown 11037 D Dual 11037 E Elfunk 11037 Emerson 11864 F Ferguson 11037 G.
VCR/PVR group Registrable input source button : . VCR D DirecTV 20739 H Humax 20739 P Philips 20739 T T iV o 20739 PVR D DirecTV 20739 H Humax 20739 P Philips 20739 T T iV o 20739 Contents Connections.
BD/DVD group Registrable input source button : . DVD 3 3D LAB 30539 A Accurian 30675 AEG 30675 Akai 30675 Alba 30539 Aristona 30539 B Bel Canto Design 31571 Blue Parade 30571 Brandt 30503 C California.
BD/DVD group Registrable input source button : . DVD-R A Accurian 30675 D Denon 30490 E Emerson 30675 F Funai 30675 G Go Video 30741 GPX 30741 L LG 30741 Loewe 30741 M Magnavox 30675 Medion 30741 P Pa.
Audio group Registrable input source button : . CD D M Denon 42867, 42868 Marantz 41985 CD-R D Denon 42868 Contents Connections Playback Settings Tips Appendix 327 Front panel Display Rear panel Remot.
License This section describes software license used for this unit. To maintain the correct content, the original (English) is used. o Boost http://www.
Definitions. “Articles” means, collectively, all articles written by Author which describes how the Source Code and Executable Files for the Work may be used by a user. “Author” means the individual or entity that offers the Work under the terms of this License.
You may distribute the Executable Files and Source Code only under the terms of this License, and You must include a copy of, or the Uniform Resource Identifier for, this License with every copy of th.
No term or provision of this License shall be deemed waived and no breach consented to unless such waiver or consent shall be in writing and signed by the party to be charged with such waiver or consent. This License constitutes the entire agreement between the parties with respect to the Work licensed herein.
0 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 0 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
o License information for the software used in the unit About GPL (GNU-General Public License), LGPL (GNU Lesser General Public License) License This product uses GPL/LGPL software and software made by other companies.
. www.denon.com D&M Holdings Inc. 3520 10308 00AD 335.
Een belangrijk punt na aankoop van elk apparaat Denon AVR-X5200W (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Denon AVR-X5200W heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Denon AVR-X5200W vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Denon AVR-X5200W leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Denon AVR-X5200W krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Denon AVR-X5200W bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Denon AVR-X5200W kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Denon AVR-X5200W . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
