Gebruiksaanwijzing /service van het product K10 van de fabrikant Directed Electronics
Ga naar pagina of 16
NO TE: This product is intended for installation b y a prof essional installer only! Any attempt to install this product by an y person other than a trained prof essional may result in se v ere damage to a vehicle’ s electrical system and components.
3 table of contents primary harness (H1) wire connection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 primary har ness (H1) wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 primary harness (H1) wire connection guide primary harness (H1) wiring diagram The primar y harness supplied with this unit is the standard 12-pin harness used.
5 H1/2 WHITE (-) Parking Light Output This wire provides a (-) 200mA output to flash the parking lights. This is suitable for driving (-) light control wires in T oyota, Lexus, BMW , some Mitsubishi, some Mazda, etc. If the vehicle has a positive parking light circuit, a relay must be used to flash the parking lights.
6 H1/6 BLUE (-) 200 mA Second Unlock Output The H1/6 BLUE output is used for progressive unlock. A progressive unlock system unlocks the driver's door when the unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again within 15 seconds after unlocking the driver's door .
7 H1/11 RED (+)12V constant power input Before connecting this wire, remove the supplied fuse. Connect to the positive batter y terminal or the constant 12V supply to the ignition switch. N N O O T T E E : : Always use a fuse within 12 inches of the point you obtain (+)12V .
8 door lock harness (H4), wire connection guide ___ ___ ___ peripheral plug-in harnesses LED, 2-pin WHITE plug The LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port. Make sure the LED wires are not shorted to ground as the LED will be damaged.
9 Pro Security Pr ogrammer interface, 3-pin port The BLACK three-pin port is provided for pr ogramming of the unit. When using the P ro Security P rogrammer , it is possible to configure any and all of the programmable functions. F or more information please refer to the guide packaged with the programmer .
10 3. T ransmit. The transmitter is used to select the desired setting. As shipped, the unit is configured to the LED ON settings. These are the default settings. Pressing the lock button will set it to the LED ON setting. The LED will light solid (stop flashing) to indi- cate the setting.
11 system features menus feature descriptions 1 ACTIVE/P ASSIVE ARMING: When active arming is selected, the starter kill will ar m (if connected) only when the transmitter is used. When set to passive arming, the starter kill will ar m (if connected) 30 seconds after the ignition key is turned off.
12 8 DOUBLE PULSE UNLOCK OFF/ON: Some vehicles require two pulses on a single wire to unlock the doors. When the double pulse unlock feature is turned on, the BLUE H2/C wire will supply two nega- tive pulses instead of a single pulse. At the same time, the GREEN H2/A wire will supply two positive pulses instead of a single pulse.
13 Channels #4-6: Channels 4 through 6 are used to assign the arm, disarm and panic functions to sep- arate buttons on the remote control. T eaching a button to Channel 4 erases all information about that remote from memor y . Any auxiliar y functions that are desired will have to be reprogrammed.
14 remote configurations The transmitters can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Remote Coding. standard configuration A remote that uses the standard configuration operates similarly to many factor y keyless entry remotes.
15 power-up Power-up ensures that the when the system is powered up it will return to the same state it was in when power is disconnected. For a full description of power-up refer to the owner's manual.
16 3-Pin 2-Wire Door Lock Harness Override Switch Pro Secur ity Programmer ® ™ wiring quick reference guide.
Get Started Get Protected Ungo Pro Security 661 W . Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2003 Directed Electroni cs, Inc . - All rights r eserved GK10 11-03.
Een belangrijk punt na aankoop van elk apparaat Directed Electronics K10 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Directed Electronics K10 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Directed Electronics K10 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Directed Electronics K10 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Directed Electronics K10 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Directed Electronics K10 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Directed Electronics K10 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Directed Electronics K10 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
