Gebruiksaanwijzing /service van het product OCDWB01 van de fabrikant Exmark
Ga naar pagina of 20
OCDWB01 OPERA TOR CONTROLLED DISCHARGE FOR W ALK-BEHIND UNITS Part No. 4500-569 Rev . A.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark equipment. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark equipment.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 1) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 1 1.
Safety collection system or m ulch kit in place and w orking properly . • Stop engine, wait for all mo ving parts to stop , remov e key and engag e parking brake: – Before c hecking, cleaning or w orking on the mow er .
Safety Safety and Instructional Decals • Keep all safety signs legible . R emo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Setup Setup Assembling Discharge Deector to OCDWB01 Insert the rod through the rst tab on the gate link frame, disc harge deector , and second tab on the gate link frame (Figure 2). Orient and install the spring so that the loop will rest in the notch on the disc harge deector .
Setup Figure 5 1. Latch 3. Front pin 2. OCDWB01 assembly 4. Slot • If the front pin does not engag e in the slot in the deck, loosen or completely remov e the hardware in the g ate link frame as shown in Figure 6. P osition the g ate link frame so that the front pin aligns with the slot.
Setup there will be room to tighten the n ut on the upper hole, on the underside of the front panel. C. Drill tw o 11/32 inc h diameter holes on the front panel as sho wn in Figure 7. D . Align the tw o holes in the mounting brack et with the front panel of the unit.
Setup B . Align the existing hole at the rear of the unit with the right hole on the brac ket. C. P osition the brac ket horizontally or with the narrow end pointed slightly downw ard. D . Using the mounting brac ket as a template , mark the left hole location onto the side panel of the unit and drill 11/32 inc h diameter hole (see Figure 11).
Product Overview Figure 14 1. V elcro strap 2. Loom clip Product Overview Figure 15 1. Handle 2. Discharge gate (under discharge deector) 3. Discharge deector 12.
Operation Operation Use the discharge gate to temporarily stop or deect g rass clippings aw ay from sidew alks , parking lots , patios , or anywhere grass clippings are not desired to be discharged. The handle allo ws the discharge gate to be held in any position from fully closed to fully open.
Operation Closing the Discharge Gate F or all W alk-Behind Units ex cept V antage: Push down on the handle to close the gate. Figure 18 1. Push down 2. Handle in gate closed position F or V anta ge Units: Push forw ard on the handle to close the gate.
Operation Figure 21 1. Handle assembly 3. Clevis pin 2. Mounting bracket 4. Hairpin 4. Unloc k the assembly and pi v ot it aw ay from the mow er deck. Lift the OCD WB01 out of the dec k mounting tube .
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Figure 22 1. Pivot bolt and nut Discharge Gate Adjustment The disc harge gate is properly adjusted in the closed position when the discharge gate is at ag ainst the discharge opening . If the disc harge gate does not close at follo w the steps below: 1.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. The following table lists some of the common causes of trouble . If assistance is needed, contact y our Exmark Ser vice Dealer .
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
Een belangrijk punt na aankoop van elk apparaat Exmark OCDWB01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Exmark OCDWB01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Exmark OCDWB01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Exmark OCDWB01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Exmark OCDWB01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Exmark OCDWB01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Exmark OCDWB01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Exmark OCDWB01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
