Gebruiksaanwijzing /service van het product 004992-0, 004992-1 van de fabrikant Generac Power Systems
Ga naar pagina of 48
Owner’ s Man ual ONL Y QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD A TTEMPT INST ALLA TION!! This manual should remain with the unit. Liquid-cooled, Prepac kaged Standb y Generators Model Nos.
Generac ® Pow er Systems, Inc. I NTRODUCTION Thank you for purchasing this model of the Guardian standby generator product line by Generac P ower Systems, Inc. Every effort was expended to make sure that the information and instructions in this manual are both accurate and current at the time the manual was writ- ten.
T able of Contents Guardian 40kW Liquid-cooled Generators Generac ® Pow er Systems, Inc. 1 INTRODUCTION ................................................ IFC SAFETY RULES .................................................... 2 Section 1 — GENERAL INFORMA TION .
2 Generac ® Pow er Systems, Inc. Study these SAFETY RULES carefully before installing, operating or servicing this equipment. Become familiar with this Owner’s Manual and with the unit. The genera- tor can operate safely , efficiently and reliably only if it is properly installed, operated and maintained.
Generac ® Pow er Systems, Inc. 3 • Inspect the generator regularly , and promptly repair or replace all worn, damaged or defective parts using only factory-approved parts. • Before performing any maintenance on the generator , disconnect its battery cables to prevent accidental start -up.
4 Generac ® Pow er Systems, Inc. 1.1 GEN ER A T OR This equipment is a liquid- cooled, engine - driven gen- erator set. The generator is designed to supply elec- trical power that operates critical electrical loads during utility power failure.
Generac ® Pow er Systems, Inc. 5 1.6 GEN ER A T OR F U EL SY S TEM The unit has been factory tested and adjusted using a natural gas fuel system. If propane (LP) gas is neces- sary , refer to Section 1.12 for conversion. F uel pressure for a natural gas set up should be five inches to 14 inches of water column (0.
6 Generac ® Pow er Systems, Inc. Figure 1.6 - Low Coolant Level Sensor 1.7 .4 O VERSPEED SH UTDOWN The engine control board receives AC frequency sig- nals from an engine run winding in the alternator . Should AC frequency exceed about 72 Hertz for three seconds or 75 Hertz instantaneously , the engine shuts down and the overspeed LED turns on.
1.1 0 SP ECIF ICA TIONS 1.1 0.1 GEN ER A T OR SP ECIF ICA TIONS 1.1 0.2 ENGI N E SP E CI F ICA TIONS Make..................................................................................................Chr ysler Displacement .........................
8 Generac ® Pow er Systems, Inc. Serious injury or damage may occur if not configured pr operly . Please consult an author- ized service dealer with any questions. 1.1 3 T ORQU E SP ECIF ICA TIONS Tighten the bolts from the middle out, in a criss- cross pattern.
Generac ® Pow er Systems, Inc. 9 After the system has been installed, do nothing that might render the installation in noncompli- ance with such codes, standards and r egula- tions.
10 Generac ® Pow er Systems, Inc. Figure 2.1 – Basic Standby Electric System 2.5 EM ERGENCY CI RCU IT IS OL A TION M E THOD This prevents overloading the generator by keeping electrical loads below the wattage/amperage capacity of the generator .
Generac ® Pow er Systems, Inc. 11 2.9 TR ANSF ER SWIT CH SIGNAL CO N N EC T I O N S 2.9.1 P RE-P ACKAGED A TS If the generator is to be installed with a pre -packaged transfer switch, it is necessary to connect the control wires to the generator and set position two of the four -position dip switch to OFF .
12 Generac ® Pow er Systems, Inc. • Spilled electrolyte is to be washed down with an acid-neutralizing agent. A common practice is to use a solution of one pound (500 grams) bicarbon- ate of soda to one gallon (4 liters) of water . The bicarbonate of soda solution is to be added until the evidence of reaction (foaming) has ceased.
Generac ® Pow er Systems, Inc. 13 Make sure the generator battery is fully charged, prop- erly installed and interconnected, and ready for use. Check to ensure that there are no loose electrical con- nections. Restrain any loose wires to keep them clear of any moving generator set components.
14 Generac ® Pow er Systems, Inc. 3.2.3 1 5 AMP F USE F use protects the control console’s DC control circuit against electrical overload. If the fuse has melted open because of an overload, engine cranking and startup cannot occur . If the fuse needs to be replaced, use only an identical 15-amp replacement fuse.
Generac ® Pow er Systems, Inc. 15 3.5 R E TR ANSF ER AN D SH UTDOWN When utility power source voltage has been restored, electrical loads may be transferred back to that source and the generator can .
16 Generac ® Pow er Systems, Inc. 4.1 MAI NTENANCE P ER FOR M ED B Y AUTHOR IZED SERVICE DEALERS A. EVER Y THR EE MONTHS 1. Check battery state of charge and condition. 2. Inspect and test fuel system. 3. Check transfer switch. 4. Inspect exhaust system.
Generac ® Pow er Systems, Inc. 17 • Add recommended coolant mixture as necessary . • P eriodically remove radiator pressure cap to make sure the coolant recovery system is functioning properly . Coolant should be at bottom of radiator filler neck.
18 Generac ® Pow er Systems, Inc. 7. Start engine and check for oil leaks. Figure 4.2 - Oil Filter 4.5.1 1 CHANGI NG TH E ENGI NE AI R CLEAN ER T o replace the engine air cleaner , (part number 0A4637), remove the air cleaner cover and replace the air filter making sure it is positioned properly before reattaching the cover .
Generac ® Pow er Systems, Inc. 19 4.6.3 BA TTER Y MAI NTENANCE The battery should be inspected per the “Service Schedule,” Section 6. The following procedure should be followed for inspection: 1. Inspect the battery posts and cables for tightness and corrosion.
20 Generac ® Pow er Systems, Inc. Section 4 — Maintenance Guardian 40kW Liquid-cooled Generators 4.7 S CH EDU LED MAI NTENANCE F ollowing is a recommended maintenance schedule for Generac small standby and residential generator sets.
Generac ® Pow er Systems, Inc. 21 Section 4 — Maintenance Guardian 40kW Liquid-cooled Generators Maintenance Level 1 Level 2 Le vel 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp .
22 Generac ® Pow er Systems, Inc. Section 4 — Maintenance Guardian 40kW Liquid-cooled Generators Maintenance Level 1 Level 2 Le vel 3 Level 4 T asks Recom- T ask Required T ask Required T ask T ask mended Comp . to be done Comp. to be done Comp . Required Comp .
Generac ® Pow er Systems, Inc. 23 Section 5 — T roubleshooting Guardian 40kW Liquid-cooled Generators TROU B LE SHOO TI NG POI NTS P ROBLEM CAUSE CORR E CTION Engine won’t crank. 1. 15 amp fuse b lown. 1. Replace fuse. 2. Loose or corroded or def ective 2.
24 Generac ® Pow er Systems, Inc. Section 6 - Electrical Data Guardian 40kW Liquid-cooled Generators Wiring Diagram — Engine — Drawing No. 0E8 1 1 5-A.
Generac ® Pow er Systems, Inc. 25 Section 6 - Electrical Data Guardian 40kW Liquid-cooled Generators Wiring Diagram — Engine — Drawing No. 0E8 1 1 5-A.
26 Generac ® Pow er Systems, Inc. Section 6 - Electrical Data Guardian 40kW Liquid-cooled Generators Electrical Schematic — Engine — Drawing No. 0E81 16-A.
Generac ® Pow er Systems, Inc. 27 Section 6 - Electrical Data Guardian 40kW Liquid-cooled Generators Electrical Schematic — Engine — Drawing No. 0E81 16-A.
CONTACTOR WIRE H ARNE SS 4 3 35 13 12 9 34 TO MOU NT E N G INE 18 8 6 7 5 16 3 4 43 42 2 36 41 40 16 6 7 5 19 16 30 27 35 3 4 36 33 27 29 22 20 3 2 38 18 31 20 21 TO S TARTER S TARTER BO LT TO E N G INE B L OC K 18 TO 11 1 12 10 1 4 R EAR BEARIN G 15 3 7 13 C ARRIER 3 4 16 2 28 Generac ® Pow er Systems, Inc.
ITEM P ART NO . QTY . DESCRIPTION 1 0E7331 1 WELDMENT MTG BASE 3.9L CR YSLR 2 052860 4 NUT FLANGED HEX M12-1.75 3 052251 4 DAMPENER VIBRA TION 40 BLUE 4 052257 4 SP ACER .49 X .62 X 1.87 PWDR/ZNC 5 052252 4 DAMPENER VIBRA TION 6 052259 4 W ASHER FLA T M12 7 052891 4 SCREW HHC M12-1.
30 Generac ® Pow er Systems, Inc. S TATE S F O AM I S O N NEAR S IDE S TATE S F O AM I S O N FAR S ID E 3 7 30 L AT C H DETAIL 3 1 3 1 3 2 34 38 3 2 3 4 43 18 17 41 4 2 DETAIL S EE LAT CH "B " 25 5 2 11 9 6 4 5 5 4 TO "A" S E CU RE A S S H O WN.
Generac ® Pow er Systems, Inc. 31 ITEM P ART NO . QTY . DESCRIPTION 1 0E8411 1 INT AKE DUCT HSB 2 0E8042 1 DUCT DISCHARGE RH FRONT 3 0E8041 1 DUCT DISCHARGE LH FRONT 4 0C2454 62 SCREW TH-FRM M6-1 X 1.
32 Generac ® Pow er Systems, Inc. Section 7 - Exploded Views and P arts Guardian 40kW Liquid-cooled Generators Control Panel — Drawing No. 0E7 11 8-G.
Generac ® Pow er Systems, Inc. 33 ITEM P ART NO . QTY . DESCRIPTION 1 0E7195 1 CONTROL BO X HSB 2 0E7196 1 CO VER FR ONT P ANEL HSB 3 0E7197 1 CO VER TOP P ANEL HSB 4 0E7193 1 DECAL W ARNINGS HSB 5 0.
Section 7 - Exploded Views and P arts Guardian 40kW Liquid-cooled Generators Engine — Drawing No. 0E81 21 -D 34 Generac ® Pow er Systems, Inc..
ITEM P ART NO . QTY . DESCRIPTION 1 0E5048A 1 FLEXPLA TE 3.9L HSB 2 0E7477 1 MA CHINING, 3.9L ENGINE AD APT OR 3 0E6703 1 CO VER, FL YWHEEL ACCESS 4 0E8336 REF REWORK, 3.9L CHR YSLER ENGINE 5 0E7841 2 GASKET , THERMOST A T AD APT OR 6 0E7254 1 MA CH, THERM AD APT OR 3.
17 WATER PUMP 24 23 26 24 25 21 3 "A" 13 1 15 19 22 TO T HERM OS TAT HOUS IN G 10 4 10 20 0 5 16 16 2 14 8 15 7 14 18 6 9 1 7 14 O "A" Section 7 - Exploded Views and P arts Guardian 40kW Liquid-cooled Generators Radiator — Drawing No.
ITEM P ART NO . QTY . DESCRIPTION 1 0D7825A 1 RADIA TOR COPPER BRASS 2 0D7174C 1 VENTURI,3.9L CR YSLR HSB 22"F AN 3 0E7640 1 RADIA TOR SUPPOR T L/H SIDE 4 0E7924 1 HOSE LOWER RADIA T OR 5 0F2853 1 HOSE, RADIA TOR UPPER, 3.9L 6 0D8252 1 F AN GUARD , T OP 7 0D8251 1 F AN GUARD , BO TT OM 8 0E0726 1 BRACKET , W A TER BO TTLE 1.
38 Generac ® Pow er Systems, Inc. 2 1 23 24 23 TO EN G INE 2 16 17 4 5 6 45 42 40 1 1 4 1 9 8 12 6 3 15 2 13 27 3 1 14 1 9 29 30 3 2 "B " TO "B " 13 36 3 7 38 20 19 18 35 3 4 M ANIF O LD INTAKE TO 44 43 25 22 6 1 39 33 Section 7 - Exploded Views and P arts Guardian 40kW Liquid-cooled Generators Fuel Syst em — Drawing No.
Generac ® Pow er Systems, Inc. 39 ITEM P ART NO . QTY . DESCRIPTION 1 033212 4 SCREW HHC 5/16-18 X 1-1/4 G5 2 075580 1 FLANGE FUEL INLET 3 0E8365 1 ASSY REG. 3.9L N/G-LPV 1800RPM 4 039253 2 SCREW HHC M8-1.25 X 20 G8.8 5 022145 2 W ASHER FLA T 5/16 ZINC 6 022129 8 W ASHER LOCK M8-5/16 7 045771 2 NUT HEX M8-1.
40 Generac ® Pow er Systems, Inc. 4 15 7 17 8 7 1 18 20 3 1 30 5 21 19 L EAD S 6 2 14 12 24 9 22 * 2 3 13* 3 10 13 11 Section 7 - Exploded Views and P arts Guardian 40kW Liquid-cooled Generators Alternator — Drawing No.
Generac ® Pow er Systems, Inc. 41 ITEM P ART NO . QTY . DESCRIPTION 1 0E5093A 1 RO T OR 390 30KW 1P DIRECT HSB 0E7413A 1 RO T OR 390 40KW 1P DIRECT HSB 2 0E5094A 1 STR-390--35AD1 HSB (382MM LONG)(3.0LFORD) 0E7412A 1 STR-390--40AD HSB (433MM LONG)(3.9L CHRYSLER) 3 0E5706 1 REAR BEARING CARRIER 390/DRCT 4 0E5048 REF FLEXPLA TE 3.
ITEM P ART NO . QTY . DESCRIPTION 1 0E8616 1 MUFFLER 7" X 9" X 21" 2.5" IN & OUT 2 0F1081 1 WYE, PIPE 3.9L CHR YSLER 3 0F1087 1 PIPE R/H SIDE 3.9L CHR YSLER 4 0E8026 1 PIPE L/H EXHA UST MANIFOLD 5 0E5914 1 BRA CKET MUFFLER 3.0L FORD HSB 6 0E8702 1 PIPE MUFFLER INLET 7 0E8727 1 PIPE MUFFLER OUT 8 036797 3 BOL T U 5/16-18 X 2.
Generac ® Pow er Systems, Inc. 43 Section 8 — Installation Diagram Guardian 40kW Liquid-cooled Generators Installation Diagram — Drawing No. 0E8422-A O VERHEAD VIEW.
44 Generac ® Pow er Systems, Inc. Section 9 - Notes Guardian 40kW Liquid-cooled Generators.
Generac ® Pow er Systems, Inc. 45 Section 9 - Notes Guardian 40kW Liquid-cooled Generators.
Part No. 0E8359 Revision F (01/24/05) Printed in U.S.A. Section 1 0 – W arranty Guardian 40kW Liquid-cooled Generators GENER AC PO WER SY S TEMS "T WO YEAR" LIM ITED W ARR ANTY FOR GUARDIA.
Een belangrijk punt na aankoop van elk apparaat Generac Power Systems 004992-0, 004992-1 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Generac Power Systems 004992-0, 004992-1 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Generac Power Systems 004992-0, 004992-1 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Generac Power Systems 004992-0, 004992-1 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Generac Power Systems 004992-0, 004992-1 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Generac Power Systems 004992-0, 004992-1 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Generac Power Systems 004992-0, 004992-1 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Generac Power Systems 004992-0, 004992-1 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
