Gebruiksaanwijzing /service van het product 407C van de fabrikant Hayter Mowers
Ga naar pagina of 28
POWER TRIM Code 407C OWNER’S HANDBOOK FROM SERIAL NO:407C001001 P ART NO: 407005 (rev .0.) ISSUE: 01-03-05.
2 F-050202L T ABLE OF CONTENTS OWNER’S INFORMA TION 4 SAFETY PRECAUTIONS 4 INTERNA TIONAL PICTORIALS 7 ASSEMBL Y 8 OPERA TION 1 1 MAINTENANCE 14 TROUBLE SHOOTING CHART 20 REP AIR P ARTS 22 Declared vibration emission values in accordance with Directive 98/37/EC.
3 F-050202L Hayter Limited warrants to the original user / purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of three years from the date of purchase.
SAFETY RULES 4 F-050202L OWNER’S INFORMA TION Know your product: If you understand the unit and how the unit operates, you will get the best performance. As you read this manu- al, compare the illustrations to the unit. Learn the location and the function of the controls.
SAFETY RULES 5 F-050202L 18. Before each use, inspect the throttle control lever and cable. Make sure that the cable is free and that the lever is not damaged. Also check the cable linkage running to the carburetor for kinks, loose fittings, and obstructions.
SAFETY RULES 6 F-050202L 2. Never run an engine indoors or inside a closed area. 3. Never make adjustments or repairs with the engine running. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental start- ing. Always wear eye protection when you make adjustments or repairs.
SAFETY RULES 7 F-050202L INTERNA TIONAL PICTORIALS IMPORT ANT : The following pictorials are located on your unit or on literature supplied with the product.
ASSEMBL Y 8 F-050202L ASSEMBL Y CONTENTS OF P ARTS BAG 1 - Owner ’s Manual 1 - Parts Bag 1 - Safety Glasses (Not shown actual size) 2 Sets - Trimmer Lines (0.155 inch diameter) 1 - Bag (4 Screws) W ARNING: Always wear safety glasses or eye shields while as- sembling the machine.
ASSEMBL Y 9 F-050202L HOW TO RAISE THE HANDLE 1. Hold the handle with one hand and loosen both handle adjustment knobs until the ratchet teeth are disengaged. Do not remove the handle adjustment knobs . See Figure 2. 2. Raise the handle to the operating position.
ASSEMBL Y 10 F-050202L ENGINE PREP ARA TION Note: Engine does not contain OIL or PETROL. W ARNING: Follow the engine manufacturer ’ s instructions for the type of petrol and oil to use. Always use a safety petrol container . Do not smoke when adding petrol to the en- gine.
OPERA TION 11 F-050202L KNOW YOUR POWERTRIM READ THE OWNER’S HANDBOOK AND ALL SAFETY RULES BEFORE YOU OPERA TE the machine. T o familiarise yourself with the location of the controls, compare the illustrations with your machine. Save this handbook for future reference.
OPERA TION 12 F-050202L HOW TO USE THE TRIMMER HEAD DRIVE LEVER 1. T o engage the trimmer head, hold the con- trol bail against the handle . Move the trimmer head drive lever forward to en- gage the trimmer head. See Figure 6. The faster the engine runs, the faster the trim- mer head will rotate.
OPERA TION 13 F-050202L HOW TO ST ART THE ENGINE NOTE: DO NOT BE ALARMED, your engine will smoke the first time it is started. It is burning off the protective coating that is on the internal engine parts. W ARNING: Never leave the ma- chine unattended while the en- gine is running.
MAINTENANCE 14 F-050202L CUSTOMER RESPONSIBILITIES SER VICE RECORDS Fill in dates as you complete regular service. Before Each Use Every 5 Hours Every 25 Hours Every 100 Hours As Noted SER VICE DA TES.
MAINTENANCE 15 F-050202L LUBRICA TION How T o Lubricate The Jackshaft Assembly A grease fitting is provided to lubricate the jackshaft assembly . Use a grease gun with au- tomotive type grease to lubricate the jackshaft assembly as shown in Figure 10.
MAINTENANCE 16 F-050202L SP ARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted or burned or if the porcelain is cracked. 1. Make sure the spark plug is clean. Clean the spark plug by carefully scraping the electrodes (do not sand blast or use a wire brush).
MAINTENANCE 17 F-050202L SER VICE AND ADJUSTMENT W ARNING: Before you inspect, clean or service the machine, stop the engine. Make sure that all moving parts have stopped. Disconnect the wire from the spark plug. HOW TO REPLACE THE TRIMMER LINE For the best performance, use a heavy gauge 3.
MAINTENANCE 18 F-050202L HOW TO REPLACE THE DRIVE BEL T T o replace the drive belt, the trimmer head and shield must be removed as follows. W ARNING: Before you remove the drive belt, disconnect the wire from the spark plug. 1. Remove the two fasteners that hold the rear o f the shield to the trimmer housing (See Figure 15) .
MAINTENANCE 19 F-050202L STORAGE W ARNING: Do not remove petrol while inside a building, near a fire, or while you smoke. Petrol fumes can cause an explosion or a fire. When the machine is put in storage for thirty days or more, follow the steps below to make sure the machine is in good condition the following season.
TROUBLE SHOOTING CHART 20 F-050202L TROUBLE CAUSE CORRECTION Engine does not start Spark plug wire disconnected. Connect spark plug wire. Engine not primed. Prime engine. Defective or incorrectly gapped spark plug. Inspect or replace spark plug. Fuel tank empty .
TROUBLE SHOOTING CHART 21 F-050202L Engine overheats. Engine cooling system clogged. Clean debris screen and engine cooling fins. Carburetor out of adjustment. Adjust carburetor . T ake the unit to an authorised Service Dealer . Oil level is low . Add oil.
Code 407C REP AIR P ARTS 22 F-050202L 1 2 3 4 5 28 6 2 7 6 8 4 9 10 9 10 4 11 16 17 11 14 12 15 14 20 22 29 23 27 16 19 30 17 6 20 25 24 31 26 33 19 32 32 34.
Code 407C REP AIR P ARTS 23 F-050202L Key No. Description Part No. 1 Lever , Stop MU740198E549 2 Bolt MU323035 3 Cable, Control Latching MU740193 4 Tie, Cable MU071372 5 Handlebar MU740196E701 6 Nut M.
Code 407C REP AIR P ARTS 24 F-050202L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 17 18 19 20 22 23 24 25 26 27 29 30 31 31 33.
Code 407C REP AIR P ARTS 25 F-050202L Key No. Description Part No. 1 Nut MU015x84 2 Screw MU025x1 1 3 Frame, Trimmer MU740150E549 4 Screw MU26x256 5 Bracket, Idler Assembly MU740231 Z 6 Bolt MU009x48 .
NOTES 26 F-050202L.
NOTES 27 F-050202L.
28 F-050202L How T o Order Replacement Parts Use only manufacturer ’ s authorised or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a P A for purchased assembly .
Een belangrijk punt na aankoop van elk apparaat Hayter Mowers 407C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hayter Mowers 407C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hayter Mowers 407C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hayter Mowers 407C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hayter Mowers 407C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hayter Mowers 407C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hayter Mowers 407C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hayter Mowers 407C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
