Gebruiksaanwijzing /service van het product NETAXS-123 van de fabrikant Honeywell
Ga naar pagina of 76
May 2010 © 2010 Honeywe ll. All rights reserved. 800-05779, Revision A NetAXS-123 Access Control Unit Inst allation Guide.
Copyright© 2010 Honeywell. All right s reserve d. All product and brand names are the service ma rks, trademarks, registe red trademarks, or registered service marks of their respec tive owners. Printed in the United S tates of America. Honeywell reserves th e right to change an y inform ation in this document at any time without prior notice.
NetAXS-123 Access Control Unit Installation Guide , Document 800-0 5779, Revision A iii C ONTENT S Inst alling the NetAXS-123 Panels 1.0 Introductio n ..................... .............. ................. ................. ................. .........
iv www.honeywell.com 4.3 RS-485 Connection via PCI-3 .................................... ........................... .......................... 50 4.4 RS-485 Connection via NetAXS-123 ................ ........................... .....................
NetAXS-123 Access Control Unit Installation Guide , Document 800-0 5779, Revision A v L IST OF F IGURES Figure 1: NetAXS-123 Compact Enclosure Wi ring and Components ............. .......................... 3 Figure 2: NetAXS-123 Standard Enclosure Panel Wiring and Components .
vi www.honeywell.com.
NetAXS-123 Access Control Unit Installation Guide , Document 800-0 5779, Revision A vii L IST OF T ABLES Table 1: Supervised Input Terminal Bl ocks ......................... ........................... ...................... ...... 5 Table 2: Supervised Tamper Terminal Blocks .
viii www.honeywell.com.
NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 1 Installing the NetAXS-123 P anels In this chapter ... Introduction 2 Panel Component s and Descriptions 3 Installat.
2 www .honeywell .com Installing the NetAXS-123 Panels Introduction 1.0 Intr oduction This document describes how to install the NetAXS-123 Standard Enclosure access control unit and the NetAXS-123 Compact Enclosure acce ss control unit.
Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 3 2.
4 www .honeywell .com Installing the NetAXS-123 Panels Panel Components and Descriptions Figur e 2: NetAXS-123 S tandar d Enclosur e Panel W iring and Compon ents Note: Maintain at least a .
Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 5 Figur e 3: NetAXS-123 Add-On Boar d W iring and Components 2.
6 www .honeywell .com Installing the NetAXS-123 Panels Panel Components and Descriptions T ampers can also be supervised. They are located on the following terminal blocks: T able 2: Supervised T ampe.
Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 7 Caution: The system has not be en verified for compliance with UL10 76 Burglar Alarm units and systems.
8 www .honeywell .com Installing the NetAXS-123 Panels Panel Components and Descriptions 2.2.2 Supported Readers Supported readers incl ude the following: T able 4: Readers Supported by NetAXS-1 23 Se.
Installing the NetAXS-123 Panels Panel Components and Descriptions NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 9 Note: For NetAXS-123 reader spec ifications, see Hardware Specifications , page 60. 2.2.3 Real-Time Clock Protection The panel R TC is back ed up using a super capa ci tor .
10 www .honeywell .com Installing the NetAXS-123 Panels Panel Components and Descriptions 2.4 Battery For the NetAXS-123 Standard Enclosure panel, one CASIL CA1270, 12 VDC, 7A-hour sealed lead-acid battery (Honeywell order number 3-000066). The b attery provides standby backup power , depending upon system configu ration and activity .
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 11 3.0 Installation 3.
12 www .honeywell .com Installing the NetAXS-123 Panels Installation 3. Mount the board onto the back of the panel. 4. Choose the tamper type (standard or of f-the-wall tamper) and wire the tamper .
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 13 • W iring an off-the-wall tamper: 5. Set the tamper , using pliers at the four locations indicated below . Wa r n i ng : Do not apply power at this tim e.
14 www .honeywell .com Installing the NetAXS-123 Panels Installation 6. Connect the Ethernet cable and the T amper wire, as shown below . 7. Set DIP switch settings for the panel addres s, communication termin ation and biasing. See DIP Switch Settings , page 36.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 15 3.1.2 Inst alling over a Gang Box 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the panel on the gang box.
16 www .honeywell .com Installing the NetAXS-123 Panels Installation 3.1.3 Inst alling on a Flat Surface 1. Review the panel layout, cable runs, and power needs. 2. Mount the back of the enclosure on the surface, either with drywall screes or threaded wall anchors.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 17 3.2 Inst alling the S t an dard Enclosure Panel Perform the followi.
18 www .honeywell .com Installing the NetAXS-123 Panels Installation 3. Install the power supply . a. Fit the power supply screws through the key hol es in the left side of the cabinet, and seat the power supply by pulling down. b. From the outside of the cabin et, tighten the screws to lock the power supply in place.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 19 c. Inside the cabinet, screw in the two se lf-tap ping screws (supplied in the product bo x) at the top and bottom of the power supply .
20 www .honeywell .com Installing the NetAXS-123 Panels Installation d. Plug the connector that is attached to the blue and brown wires into the power supply .
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 21 4. Select one of the following three poss ible entry points for the power cable: Wa r n i ng : Do not apply power at this time.
22 www .honeywell .com Installing the NetAXS-123 Panels Installation 5. Use a pencil to mark the loca tion of the holes on the wall. 6. Screw the NetAXS-123 Controller Board with the four captive scre.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 23 7. Hold the Add-On Board over the Controller Boar d and seat th e board-to -board connector into the Controller Board.
24 www .honeywell .com Installing the NetAXS-123 Panels Installation 8. Connect the wiring harness, as shown. Wa r n i ng : DO NOT CONNECT the AC pow er or the battery wires yet! 9. Power up the NetAXS-123 Controller Boar d and configure the sy stem. Refer to the NetAXS-123 S tartup Guide (800-05780) for instructions.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 25 10. Connect the battery . 1 1. Attach the door to the cabinet. 12. Re-connect the green ground wire to the cabinet door .
26 www .honeywell .com Installing the NetAXS-123 Panels Installation 3.3 Inst alling th e Add-On Board Wa r n i ng : T o prevent damage to the NXC1 Controller Board, rem o v e po w e r from the NetAXS-123 panel before install ing or removing a NetAXS-123 Add-On Board.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 27 2. Pick up the Add-On Board and no tice the four posts on the bottom.
28 www .honeywell .com Installing the NetAXS-123 Panels Installation 5. Set the relay jumpers. a. Use the following figure to locate the jumpers. b. See Add-On Board DIP Switch and Jumper Settings , page 40, to set the power source (12VDC power or external power) and the relay contact position (Normally Open or Normally Closed).
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 29 3.4 Wiring the Readers Each reader port supports one or two readers (entry and exit readers) with W iegand output format.
30 www .honeywell .com Installing the NetAXS-123 Panels Installation Ta b l e 5 show s the input/output factory de fault wiring for a one-door config uration on the Controller Board. T able 5: Factory Default Configuration Settings for Door 1 a Readers A and B share the same connection.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 31 Notes : • The Controller Board includ es Inputs 7 and 8 but they are reserved for s ystem use.
32 www .honeywell .com Installing the NetAXS-123 Panels Installation Ta b l e 7 lists the factory Add-On Board default settings for a door 3. These mappings should be used for the readers, inputs, and outputs when either a 1- or 2-door Add-On Board is attache d to the board-to-board connector on the controller board.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 33 • NetAXS-123 supports a variety of W iegand reader models. Some readers have only one brown wire for LED control; others have two possib le LED control inputs--orange f or the green LED and brown for the re d LED.
34 www .honeywell .com Installing the NetAXS-123 Panels Installation 2. Use the following figure to wire the door stri ke/mag lock according to the power supply used. Be sure to use the S4 suppressor kits as shown below . Notes: • As shown in the illustration above, the Dr y C terminal for the On -Board option should not be connected.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 35 3.6 Setting DIP Switches and Jumpers 3.6.1 Controller Board DIP Switch and Jumper Settings Figure 6 locates the NetAXS-123 DIP switch panel an d the output 1 and output 3 rela y jumpers.
36 www .honeywell .com Installing the NetAXS-123 Panels Installation DIP Switch Settings Use the following DIP switch configur ations to set the panel address.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 37 O F F O NO NO F F O N Address 22 ON ON ON OFF ON Address 23 OFF OFF.
38 www .honeywell .com Installing the NetAXS-123 Panels Installation Note: Address 0 is not a valid setting. b. Both DIP Switch 8 and DIP Switch 9 need to be either ON or OFF to be properly configured.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 39 Jumper Settings The NetAXS-123 Controller Board provides two jumper sets, one each for output relay 1 and output relay 3.
40 www .honeywell .com Installing the NetAXS-123 Panels Installation Note: The power source selected by the jumper setti ngs shown ab ove configur e the power source for the relay . It does not configure the power source for the panel. • Setting the jumpers to configure the relay contact type: 3.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 41 used to select Normally Open (NO) or Normally Closed (NC) relay contacts. There is a total of four 3-pin jumpers (two per relay) on the controller b oard.
42 www .honeywell .com Installing the NetAXS-123 Panels Installation 3.7 Communications 3.7.1 USB Communications The NetAXS-123 Controller Board p rovides a version 2.0 USB port that connects to the web b rowser or to a WIN-P A K host. The following figure identifies the location of the port on the board.
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 43 2. Click Install USB Drivers on the product men u to start the USB driver installation wizard. 3. Click Next to display the Ready to Install the Program screen.
44 www .honeywell .com Installing the NetAXS-123 Panels Installation 5. When the installation is comple te, the closing screen appears: 6. Click Finish . 7. Connect the computer to the NetAXS-123 co ntroller with a USB-A to Micro USB-B cable. 8. T urn on the power to the NetAXS-123 controller .
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 45 DIP switch SW1 positions 8 and 9 are provided for supplying biasing and end-of-line termination for the RS-485 network.
46 www .honeywell .com Installing the NetAXS-123 Panels Installation Figur e 10: RS-485 Configuration via NetAXS-12 3 Gateway This configuration supports a total of 31 NetAXS and NetAXS -123 panels per Multidrop line. Reader 4 Reader 3 Reader 4 Reader 1 NetAXS-123 Gateway .
Installing the NetAXS-123 Panels Installation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 47 3.7.3 Ethernet TCP/IP Communications Figur e 1 1: Ethernet TCP/IP Configuration This configuration supports a total of 31 NetAXS and NetAXS -123 panels per Multidrop line.
48 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.0 System Configuration This section provides wiring diagrams for each of the NetAXS-123 system co nfigurations.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 49 4.2 USB Connection Figur e 13: NetAXS-123 USB Connection Note: The USB connection i s intended to be used for system maintenance and troubleshootin g.
50 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.3 RS-485 Connection via PCI-3 This connection supp orts th irty-one NetAXS-123 pane ls for each drop line. No te that PCI-3 units can also be wired in interior , as we ll as in endpoint, positions.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 51 4.4 RS-485 Connection via NetAXS-123 This connection supports a total of 31 NetAXS-123 pa nels ( including the Gateway) for each drop li ne.
52 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.5 RS-485 Connections with Multidro p Panels at Both Ends of the Cable Y ou can connect Multidrop panels at both ends of an RS-485 cable via either a NetAXS-123 panel or a PCI-3 device.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 53 Figur e 17: RS-485 Connection via PCI-3 with Multidr op Panels at Both Ends Note: Y ou should ground each NetAXS-123 S tandard (Metal) Enclosure panel individually with an Earth Ground.
54 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.6 M-56K Dial-up Modem, RS-4 85 Connection via Hub (PCI-3) This configuration supports 3 1 NetAXS-123 panels for each drop line.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 55 4.7 Fiber Converter to RS-485 Connection via PCI-3 This connection supp orts 31 NetA XS-123 panels for each drop line.
56 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.8 Fiber Converter to RS -485 Connection via NetAXS-123 This connection supp orts 31 NetA XS-123 panels for each drop line.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 57 4.9 N-485-PCI-3/NetAXS -123 Access Controller Pa nel Connec.
58 www .honeywell .com Installing the NetAXS-123 Panels System Configuration 4.10 NetAXS-123/NetAXS -123 Access Controller Panel Connection Det ail Figur e 22: NetAXS-123/NetAXS-123 Access Contr oller Panel Connection Detail X DO NOT C ONNECT or GROUND SHIELD Ground only one side of cable shield Shield Ground Shield 485 - 485 Common 485 + 4,000 ft.
Installing the NetAXS-123 Panels System Configuration NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 59 4.1 1 Mixed Loops This mixed-loop configur ation supports a combined total of 31 N1000 III, N1000 IV , NetAXS, NetAXS-123, and NS2 panels per Multidrop line.
60 www .honeywell .com Installing the NetAXS-123 Panels Hardware Specifications 5.0 Har dware Specifications The specifications in this section apply to both th e Standard Enclosure and Comp act Enclosure panels. 5.1 Relay Cont act s Maximum of six Form-C SPDT relays, 3A (at dry co ntact) or 0.
Installing the NetAXS-123 Panels Hardware Sp ecificatio ns NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 61 Example : If the total current consumption of your ext.
62 www .honeywell .com Installing the NetAXS-123 Panels Hardware Specifications 5.6 Environment • T emperature: 0C to 49C operating, -55 C to +85C storage.
Installing the NetAXS-123 Panels Basic S tandalone Operation NetAXS-123 Access Control Un it Installation Guide , Document 800-05779, Revision A 63 6.0 Basic Standalone Operation 6.1 Card Read / Door Lock Operation 1. Present a card to a reader . 2. The reader sends the card number to a reader input on the panel.
64 www .honeywell .com Installing the NetAXS-123 Panels Maintenance 7.0 Maintenance Perform the following maintenanc e on the NetAXS-123 enclosure: • Change the backup battery ever y two to two-and-a-half years.
Installing the NetAXS-123 Panels T roubleshooti ng NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 65 8.0 T r oubleshooting Note: The NetAXS-123 EOL network is AC -coupled.
66 www .honeywell .com Installing the NetAXS-123 Panels T echnical Support 9.0 T echnical Support 9.1 Normal Support Hours Monday through Friday , 7:00 a.m. to 7:00 p.m. Central Standard T ime (CST), except company holidays: (8 00) 323-4576. 9.2 We b For technical assistance please vi sit http://www .
Installing the NetAXS-123 Panels T echnical Support NetAXS-123 Access Control Unit Installation Guide , Document 800-05779, Revision A 67 This p age is left blank for printing purposes.
Honeywell Access Systems 135 W . F orest Hill A venue Oak Creek, WI 53154 United States 800-323-4576 414-766-1798 F ax www .honeywellaccess.com Specifications subject to change without notice.
Een belangrijk punt na aankoop van elk apparaat Honeywell NETAXS-123 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Honeywell NETAXS-123 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Honeywell NETAXS-123 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Honeywell NETAXS-123 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Honeywell NETAXS-123 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Honeywell NETAXS-123 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Honeywell NETAXS-123 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Honeywell NETAXS-123 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
