Gebruiksaanwijzing /service van het product IE-IMCV-T1-MUX/4 van de fabrikant IMC Networks
Ga naar pagina of 36
IE-iMcV-T1-Mux/4 + Ethernet Operation Manual.
FCC Radio Frequency Inter ference Statem ent This equipment has been tested and found to comply wi th the limi ts fo r a Cla ss A comp uting d evice , purs uant t o Part 15 of the F CC Rules. These limits are designed to pr ovide reasonable protection against harmful interference when the equipment is operat ed in a com mercial envi ron ment.
ii Table of Cont ents FCC Radi o Fre q uenc y Int er fere nce Sta tem ent -------- -------------- ------------ --------------- - i Warr ant y -------- -------------- ------------- ------------ -------.
iii Trou ble sho otin g --------- -------------- ------------ ------------ --------------- ------------ ----------- 24 Spec ifi cati ons - ------------ ------------ -------------- ------------ -------.
1 Abou t th e IE-iM cV-T1 -Mux/4 + Ethern et Overvi ew Th e IE-iMcV-T1- Mux/4 + Et hernet is a media conv erter th at transpo rts four independent T 1 lines over an existing single (or du al, “1+1”) standard fibe r optic line operating at an effective rate of 155Mbps.
2 The IE-iMcV-T1 -Mux/4 + Et hernet offers the follow ing feat ures: • Four T1 ports with RJ-48 connectors • One full ban dwidth Etherne t 10/100BaseT por t (specifi c model) • 1+1 prot ection s.
3 Product Applicat ion The IE-iMcV-T1 -Mux/4 + Ethern et delivers 4 T1 line s to a customer's site over a protected, dedicate d fiber line. In ad dition, one serial RS -232 line an d one 10/100BaseT E thernet line can be carried at t he same time.
4 configuration on the unit will b e used. The stored con figuration can b e retrieved fr om the SNMP Management M odule or the DIP S witches. • Replacing the same type of iMc V-Module - If the DIP .
5 1+1 Pr otecti on on the Fiber In terfac e mode The fiber transport is a 1+1 protection swi tched transport. It provides very fast (<50 mSec) switch-to-protec t timing by transmitting the sam e information on both fibers at the same time. The fiber receiver then chooses the fiber to receive based on the validity of the line.
6 iView² Ma nagement Soft ware iView² is the I MC Networks management s oftware designed specific ally for the IMC Networks “iMc V” family of module s. It features a GUI and gives network managers the ab ility to monitor and co ntrol th e manageable I MC Networks product s.
7 LED Operation The IE -iM cV-T 1-M ux/4 + Ethe rne t featu res di agn osti c LED s as explained below. 10/100BaseT C onnector LNK: • OFF when port is not linked/connected • Glow s green when link.
8 SFP Ports or One model offers two SFP (A and B) por ts for 1+1 protecti on; a second mo del offers one SFP without protection. ACT: • Glows green when the SFP port is th e acti ve receive li ne.
9 DIP Swit ch Assignme nts DIP Swit ch Assignme nts A single 10-pos ition DIP Switch is located on t he unit to set the configuration . The switc h positi ons are define d as foll ows: Switch # Functi.
10 Installat ion Instruct ions Each IE-iMcV-T1-Mu x/4 + Ethernet module re quires two slots in an iMedia C hassis Series, MediaChassis/2 Series, or IE -MediaChassis/2 series. To install the module in a chassis, remove the bl ank faceplates coveri ng the slots whe re the module is to be installed.
11 Configu ration Opt ions The following sections describe the configurable features. From the CLI "Unit Configura t ion," use th e "Factory Defaul t" co mmand to rest ore the unit's default settings in the CLI, under Unit C onfiguration.
12 Fiber Fault Loopback (FFL) When a Fiber LOS is detecte d, the unit sen ds a Remote Alarm Indi cation) back to the fiber in the opposite dire ction. The re ception of fault in dication on the fiber line inhibits sending a LINK signal to the Ethernet port.
13 Loopback Each T1 port can be tested in loopback mode by enabling eithe r a Host loopback or Remote loopback test pa th. This capability allows the en d-user to help troublesho ot and isola te syste m problem s such as impr oper/broken line terminations, cables or malfunctioning equipment.
14 Console Screen s Configur ation Using the Console Port The following section describes configurat io n using the console screens. The Remote modu le is on ly confi gured th rough th e Host.
15 Main Menu From the main menu, the end-user can vie w essential unit configur ation data and a clock indicating when the displaye d information was last refreshed.
16 The screen displays the current status for items 1 through 8. For security re asons, the curren t use rna me an d pas swo rd are not displ aye d. For items 1 thr ough 8, enter the nu mber of the menu item t o be changed, an d then enter the new value w hen prompted.
17 SFP Line Status Screen The SFP Line Status screen displays the status of the Host and Remote SFP links. The de tai led SFP information may be vie wed by entering "1" for SFP A or "2" for SFP B. Displayed data includes the ma nufacturer name, code, part number an d revision number.
18 Enter th e number of the menu item to change its co nfigur ation, and then enter th e new val ue(s) w hen pr ompted. Ethernet Port Stat us Scree n This screen displays the current Eth ernet port stat us for both the Ho st and R emote site.
19 Host T1 Port Setup Screen Enter th e number of the menu item to ed it, and enter the new value( s) when pro mpted. T1 Po rt St atus Scre en Use this screen to display the current status for each of the four T1 ports fo r the Host and Remote uni ts.
20 Fiber Op tic Port Verification As a tro uble shoo ti ng aid , the f iber opt ic por ts can be ver if ied by plac ing a phys ica l loopback optical line on the por ts and verify the LED behavior as shown: The AC T LED will arbitr arily be con figured to either the A or B fiber line.
21 T1 Po rt Verif ica tio n By placing a physical l oopback conne ction on the T1 port, a valid signal can be det ected by each ind ividual T1 port to verify it s opera tion.
22 T1 Port Ma ting Connector Pinout Th e followi ng table l ists th e pin co nfigura tion for t he st andard RJ-48 T1 port mating connectors. Pin Signal 1 Receive 1 (T ip in to unit) 2 Receive 2 (Ring.
23 RS-232 Serial Console Por t The fo llowing tabl e lists th e pin config urat ion for the RS-232 3-pin Mini Jack m ating connector for the console serial port.
24 Trouble shooti ng • All IE-iMcV-T1 -Mux/4 + Etherne t units are shipped c onfigured as Host un its via DIP Switch #1 = OFF. The Remote unit should be set to DIP Switch #1 = ON. Be su re to c onfirm that the iMcV-T1 -Mux/4 card is set correctly when used.
25 Spec ific atio ns Power Consumption (Typical): 0.96A @ +5 VD C Operatin g Temper ature: +32°F to +158°F (0°C to +70°C) Storage T empe rature: -40°F to + 158°F (-40° C to +70 °C) Humidi ty: 5% to 95 % (non -conde nsing) Dimen sions : Dual Slot iMc V module MTU: Maximum pa cket size up to 1916 byte s Standards/Compliance • IEEE 802.
26 Definition of Te rms/Acronyms The following are terms and phrases used with in this manual, or which are found in docu ments as sociat ed with this equipm ent. 1+1 The Term “1+1” refers to line p rotection w here identical information i s transmitted on two re dundant lines.
27 FFL Fiber Fault Loopback: W hen the fibe r line fails, the Ethernet port that is being f orwarded over t he fiber line is f orced out of LINK. Similar to the Fiber Ale rt function. GUI Graphical User Interfac e: Software t hat prov ides a vis ual interface to enable an end-user to mana g e and monito r network devices.
28 RAI Remote Al arm Indicati on: Status inform ation rece ived from the line ind icating there i s an alarm co ndition at the f ar end of the transport.
29 IMC Networks Technical Suppor t Tel: (949) 465 -3000 or (800) 62 4-1070 (in t he U.S. and Canada); +32-16-550 880 (Europe) Fax: (949) 465-3020 E-Mail: techsu pport@i mcnetwork s.
30 Fiber Op tic Cleaning Guidelines Fiber Optic tran smitters and re ceivers are extreme ly susceptible to c ontamination by particles of d irt or dust, which can obst ruct the optic path and cause p erformance degradation. Good system performan ce requires clean optics and connector ferrules.
31 Certi fic atio ns CE: The products described herein comply with the Council Directive on Electromagne tic Compatibilit y (2004/108 /EC). European Directive 2002/96/EC (WEEE) requir es that any equipment that bears this symbol on product or packagin g must n ot be dispose d of wi th unsorte d municipal waste.
19772 Pauling • Foothill Ranch, CA 926 10-2611 US A TEL: (94 9) 465-3000 • FAX: (949 ) 465-3020 www.imcnetworks.com © 2010 I MC Networks. A ll rights r eserved. The info rmation in this docum ent is subject to change w ith out no tice. I MC Network s assumes no responsibi lity for any errors that may appear in this docume nt.
Een belangrijk punt na aankoop van elk apparaat IMC Networks IE-IMCV-T1-MUX/4 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen IMC Networks IE-IMCV-T1-MUX/4 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens IMC Networks IE-IMCV-T1-MUX/4 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding IMC Networks IE-IMCV-T1-MUX/4 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over IMC Networks IE-IMCV-T1-MUX/4 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van IMC Networks IE-IMCV-T1-MUX/4 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de IMC Networks IE-IMCV-T1-MUX/4 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met IMC Networks IE-IMCV-T1-MUX/4 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
