Gebruiksaanwijzing /service van het product DTM-5.3 van de fabrikant Integra
Ga naar pagina of 32
A V Receiv er DTM-5.3 Instr uction Manual Thank y ou f or purchasing the Integr a A V Receiv er . Please read this manual thor oughly bef ore mak- ing connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optim um perf or m ance and listening enjoyment fr om y our new A V Receiver .
2 Impor tant Safeguar ds 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference.
3 21. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that ha v e the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
4 Features ■ P ower output 100 watts per channel, min RMS, at 8 ohms, both channels driven fr om 20 Hz to 20 kHz, with no more than 0.08% THD ■ Discrete output stage circuits f or true high-curren.
5 Remote contr oller description Note: When you use the b uttons that apply to specific mode (i.e., D VD mode, RCVR/T ape mode, or CD mode), you must press the corr esponding mode button first. Standby ( ) button This button sets the unit to Standby mode.
6 Fr ont panel description This section identifies and explains the controls and displays on the front panel of the DTM-5.3. Front panel Display Standby/On b utton Press this button to turn on the po wer to the DTM-5.3. The display indicators light up.
7 Fr ont panel description F. TUNED indicator This indicator lights up when the unit receiv es a radio sta- tion signal G. STEREO indicator The indicator lights up when the unit receiv es an FM ste- reo radio station signal. H. MEMOR Y indicator The indicator lights up when you press the Memory but- ton to program a radio station.
8 Rear panel description This section identifies and explains ho w to use the terminals found on the rear of the DTM-5.3. Before connecting your audio and video compo- nents, be sure to read this section carefully and then proceed to the explanations on how to connect each indi vidual component (see page 10).
9 Rear panel description Depending on the impedance of the speakers used, set the SPEAKER IMPED ANCE SELECTOR on the rear panel as shown in the table. A C INLET Plug the supplied power cord into this A C INLET and then into the power outlet on the w all.
10 Connecting components This section explains ho w to connect the main components to the DTM-5.3 in the standard manner . • Be sure to always refer to the instruction manual that came with the component that you are connecting. • Do not plug in the power cord until all connections ha ve been made.
11 Connecting components Example of video equipment connections If there should be interference between the TV and this unit, place this unit as f ar from the TV as possible. W e do not recommend the use of a common TV/FM antenna. (Refer to “Connecting antennas” on page 13.
12 Connecting speaker s Connecting the speaker Y ou can connect two separate pairs of speaker systems. Please connect each speaker according to the illustration, observing the correct connections for R, L, + and –. Check the speaker impedance, then set the SPEAKER IMPED ANCE SELECTOR switch accordingly .
13 Connecting antennas T o use the tuner of the DTM-5.3, it is necessary to prepare the supplied FM and AM antennas. • Adjustment and placement of the FM and AM antennas for better reception is best performed while listening to a station broadcast. • If better reception cannot be obtained, then placement of an outside antenna is recommended.
14 Connecting the remote zone (Zone 2) The DTM-5.3 allows you to connect an additional set of speak ers and place them in a different room or an area separated for listening to music. This other room or area is referred to as the remote zone (Zone 2), while the room in which the DTM-5.
15 Operating components not reached b y the remote contr oller signals (IR IN/OUT) The f ollowing equipment (sold separately) is essential for operation: • Onkyo’ s Multi-Room System kits (IR Remote Controller Extension System), or • Multiroom A/V distribution and control systems from Niles ® and Xantech ® to name a fe w .
16 Standby/On Speakers A B Phones Bass Treble Balance L R Master Volume Video Tape 2 Monitor Tape 1 FM AM Phono CD DVD Zone 2 Off Memory Clear Character Direct Tuning FM Mode Display Standby DTM - 5.
17 Installing the remote contr oller batteries Installing the batteries 1 Open the battery compar tment cover by pushing the tab and opening the cover . 2 Insert two AA (R6 or UM-3) batteries into the batter y compartment. Carefully f ollow the polarity diagram (pos- itive (+) and negative (–) symbols) inside the batter y compartment.
18 Basic operations Listening to y our fav orite source 1 Select the source you wish to listen to using the input selector (e .g., PHONO). Confirm that the indicator is not lit when a source other than T ape 2 Monitor is selected. Also check that the A UDIO MUTE indicator is not lit.
19 Basic operations Listening using the headphones Y ou can connect stereo headphones with a standard binaural (ste- reo) plug to the Phones jack. When the headphone plug is inserted, the speakers are not automat- ically muted but can be controlled using the Speak ers A/B buttons.
20 Receiving stations T uning the radio (Manual tuning) When the frequency is not kno wn (Manual tuning) 1 Press the FM or AM button. 2 Use the T uning buttons (or T uning Down and Up buttons on the remote controller) to change the fre- quency . (Up).
21 Receiving stations Listening to stereo radio stations (FM only) If you tune in a stereo FM station, the STEREO indicator will be illuminated if the signal is sufficiently strong. If the signal is weak, it may be impossible to tune in the desired station.
22 Receiving stations Selecting preset stations First, select the tuner as the source by pressing the AM or FM input selector button. Input the memory number you wish to receiv e by pressing the number buttons. F or the remote controller , press the RCVR/T ape mode button before pressing the number b uttons.
23 Entering station names While receiving a preset FM or AM station, a maximum of eight characters consisting of letters, numbers and some symbols can be stored to represent the station name. Characters which can be entered: Note: F or the remote controller , press the RCVR/T ape mode button before performing the procedure in this section.
24 Recor ding a sour ce Recording an audio sour ce Please read the instruction manuals concerning operation of each unit. 1 Insert a blank tape into the tape deck. 2 Press the button (other than T ape 2 Monitor) for the source y ou wish to record. • When D VD or V ideo is selected, the audio portion of the pro- gram will be recorded.
25 Recor ding a sour ce Video disc play er (or video camcorder) to VCR recording V ideo disc programs can be recorded onto a VCR (VIDEO). 1 Load a disc in the video disc player , and a blank tape in the VCR (VIDEO). 2 Press the DVD b utton. 3 Begin playback on the video disc play er and begin recording on the VCR.
26 Using T ape 2 Monitor Unless the component connected to the T APE 2 connectors is used, the indicator in the main unit’ s display should not be lit; otherwise, the sound from other sources will not be heard. If a 3-head tape deck is connected to the T APE 2 connectors, you can use the T ape 2 Monitor to monitor the recording.
27 Enjo ying m usic in the remote zone Zone 2 operation from the main r oom T o select a source for the zone 2 r oom other than the source selected for the main r oom. 1 Press the Zone 2 button, the Zone 2 indicator fl ashes. 2 Select an input source within five seconds.
28 Using the remote contr oller Setting the ID number Programming the remote controller ID (This procedure is not required if you are using only one DTM-5.3.) If you are using multiple DTM-5.3 units, all units will respond to an operation on one of the remote controllers.
29 Contr olling other components Y ou can operate an -connected Integra/Onkyo CD player , cassette tape deck or D VD player using the remote controller pro vided wi th the DTM-5.3. Controlling an Integra/Onky o CD player The connector of the Integra/Onkyo compact disc player must be connected to the DTM-5.
30 Contr olling other components Controlling an Integra/Onky o cassette tape dec k The connector of the Integra/Onkyo cassette tape deck must be connected to the DTM-5.3. 1 Press the RCVR/T ape button. 2 Press the desired operation button. : Plays side A (the side facing the front) of the tape.
31 T r oubleshooting guide If a problem occurs, while you are using the remote controller , first operate the unit using the front panel controls to confirm that it is not due to a malfunction (or expired batteries) of the remote controller .
32 SN 29343292A I0204-2 E Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.
Een belangrijk punt na aankoop van elk apparaat Integra DTM-5.3 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Integra DTM-5.3 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Integra DTM-5.3 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Integra DTM-5.3 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Integra DTM-5.3 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Integra DTM-5.3 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Integra DTM-5.3 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Integra DTM-5.3 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
