Gebruiksaanwijzing /service van het product DTR-7.8 van de fabrikant Integra
Ga naar pagina of 128
DTR-7.8 Instr uction Manual AV Receiv er DTR-7.8_En.book Page 1 Friday, May 9, 2008 1:56 PM.
2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings.
3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.
4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel.
5 Contents Features ............................................................ 6 Supplied Accessories ...................................... 7 Multiroom Capability ........................................ 8 Getting to Know the AV Receiver ..........
6 Features Amplifier • 7-channel amplifier • 130 watts minimum continuous po wer per channel, 8 ohm loads, 2 channels driv en from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.
7 Features —Continued *9 ©2005 SIRIUS Satellite Radio Inc. “SIRIUS, ” SiriusConnect, the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. A vailable only in the contiguous United States (excluding Alaska and Hawaii) and Canada.
8 Multir oom Capability Y ou can use three speaker systems with this A V receiver —a surround-sound speaker system (up to 7.1 channels) in your main listening room, a stereo speaker system in a second room, or Zone 2, as we call it, and another stereo speaker system in a third room that we call Zone 3 (external po wer amplifier required).
9 Getting to Kno w the A V Receiver The actual front panel has various logos printed on it. They are not sho wn here for clarity . For detailed information, see the pages in parentheses. A Standby/On b utton (43) Sets the A V receiver to On or Standby .
10 Getting to Know the A V Receiver —Continued E Zone 3 indicator (115) Flashes when Zone 3 is being set. Lights up when Zone 3 is on. F Remote-control sensor (14) Receiv es control signals from the remote controller . G Stereo button (82) Selects the Stereo listening mode.
11 Getting to Know the A V Receiver —Continued For detailed information, see the pages in parentheses. 1 Speaker/channel indicators (87) Indicate the speaker configuration and channels used by the current input source. – : A box is displayed for each speaker that’ s set in the Speaker Configuration.
12 Getting to Know the A V Receiver —Continued A REMO TE CONTROL This (Remote Interacti ve) jack can be con- nected to the jack on another -capable Inte- gra/Onkyo component for remote and system control.
13 Getting to Know the A V Receiver —Continued N IR IN A/B and OUT A commercially av ailable IR recei ver can be con- nected to the IR IN A or B jack, allo wing you to control the A V receiver while you’ re in Zone 2, or control it when it’ s out of sight, for e xample, installed in a cabinet.
14 Remote Contr oller Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion.
15 Remote Controller —Continued As well as the A V receiver, you can also use the remote controller to control your other A V components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the Remote Mode buttons.
16 Remote Controller —Continued For detailed information, see the pages in parentheses. A Standby b utton (43) Sets the A V receiver to Standby . B On button (43) T urns on the A V receiv er. C Input Selector buttons (60) Used to select the input source.
17 Remote Controller —Continued To set the remote controller to D VD mode, pr ess the [D VD] Remote Mode button. A Standby b utton Sets the D VD player to Standby . B On button T urns on the D VD player . C Number buttons Used to enter title, chapter , and track numbers, and to enter times for locating specific points.
18 Remote Controller —Continued To control an Integra/Onky o CD player , MD recorder , or CD recorder , or a CD or MD player/r ecorder made by another manufacturer , press the [CD] Remote Mode b utton to select the CD/MD/CDR remote contr oller mode.
19 Remote Controller —Continued Dock mode is for controlling an Apple iPod in an Onk yo RI Dock. When Using an RI Dock: • Connect the RI Dock to the T APE IN or GAME/TV IN L/R jacks. • Set the RI Dock’ s RI MODE switch to HDD or HDD/DOCK. • Set the A V receiver’ s Input Display to DOCK (see page 49).
20 Connecting Y our Speakers Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring Dolby Digital or DTS.
21 Connecting Y our Speakers —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve.
22 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: •Y ou can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more b ut less than 6, be sure to set the speaker impedance to 4 ohms (see page 44).
23 Connecting Y our Speakers —Continued The FR ONT L/R and SURR B A CK L/R terminal posts can be used with front speakers and surround back speakers respecti vely , or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing impro ved bass and treble performance.
24 Connecting Antennas This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner .
25 Connecting Antennas —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft.
26 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections.
27 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver.
28 Connecting Y our Components —Continued ■ HDMI Monitor Setting Set to No W ith the HDMI Monitor setting set to No (see page 45), video input signals flow through the AV receiv er as shown, with composite video and S-V ideo sources being upcon v erted for the component video output.
29 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
30 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a D VD or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
31 Connecting Y our Components —Continued Hooking Up the Multichannel Input If your D VD player supports multichannel audio formats such as D VD-Audio and SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel input.
32 Connecting Y our Components —Continued W ith this hookup, you can use the tuner in your VCR or D VR to listen to your fa vorite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to the VCR or D VR in Zone 2 or Zone 3.
33 Connecting Y our Components —Continued Notes: • The A V receiv er must be turned on for recording. Recording is not possible while it’ s on Standby .
34 Connecting Y our Components —Continued W ith this hookup, you can use your satellite or cable receiv er to listen to your fav orite TV programs via the A V receiver, which is useful if your TV has no audio outputs. •W ith connection , you can listen to and record audio from the video source or listen in Zone 2 or Zone 3.
35 Connecting Y our Components —Continued About HDMI Designed to meet the increased demands of digital TV , HDMI (High Definition Multimedia Interface) is a ne w digital interface standard for connecting TVs, projectors, DVD players, set-top box es, and other video components.
36 Connecting Y our Components —Continued Making HDMI Connections ■ Video Signals Digital video signals receiv ed by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV . Composite video, S-V ideo, and component video sources can be upcon v erted for the HDMI output.
37 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your game console or listen in Zone 2 or Zone 3. •T o enjoy Dolby Digital and DTS, use connection . (T o record or listen in Zone 2 or Zone 3 as well, use and .
38 Connecting Y our Components —Continued Connecting a Camcorder or Other A V Component Connection A V receiver Signal flow Camcorder A UX 2 Input S Video ⇐ S-Video output A UX 2 Input Video ⇐ .
39 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the CD player or listen in Zone 2 or Zone 3. •T o connect the CD player digitally , use connection or . (T o record or listen in Zone 2 or Zone 3 as well, use and , or and .
40 Connecting Y our Components —Continued •W ith connection , you can play and record or listen in Zone 2 or Zone 3. •T o connect the recorder digitally for playback, use connections and , or and . •T o connect the recorder digitally for recording, use connection .
41 Connecting Y our Components —Continued ■ If Y our iPod Supports Video: Connect your RI Dock’ s audio output jacks to the AV receiv er’ s GAME/TV IN L/R jacks, and connect its video output jack to the A V receiver’ s GAME/TV IN V jack. (Onkyo DS-A2 hookup sho wn below .
42 Connecting Y our Components —Continued W ith (Remote Interactive), you can use the follo wing special functions: Auto P o wer On/Standby When you start playback on a component connected via , if the A V receiv er is on Standby , it will automatically turn on and select that component as the input source.
43 T urning On the A V Receiver Standby/On Standby/On + - On Standby TV Input TV CH TV VOL -- / --- 10 11 12 D.TUN +10 0 Clear 123 456 789 Input Selector VCR / DVR CBL / SAT DVD Tape Tuner CD Phono Ga.
44 Fir st Time Setup This section explains the settings that you need to make before using the A V recei ver for the very first time. If the impedance of any speaker is 4 ohms or more b ut less than 6, set the Speaker Impedance to 4 ohms.
45 First Time Setup —Continued If you connect your TV to the COMPONENT VIDEO MONITOR OUT 1 or COMPONENT VIDEO MON- ITOR OUT 2/ZONE 2 OUT , set the HDMI Monitor set- ting to No so that the onscreen s.
46 First Time Setup —Continued Notes: • See page 27 for charts showing ho w the HDMI Moni- tor setting affects the video signal flo w through the A V receiv er. • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
47 First Time Setup —Continued Notes: • Each HDMI IN cannot be assigned to more than one input selector . • For composite video, S-V ideo, and component video upcon version f or the HDMI OUT , the HDMI Monitor setting must be set to Y es (see page 45).
48 First Time Setup —Continued If you connect a video component to a COMPONENT VIDEO IN, you must assign that input to an input selector . F or example, if you connect your D VD player to COMPONENT VIDEO IN 3, you must assign COM- PONENT VIDEO IN 3 to the D VD input selector .
49 First Time Setup —Continued Notes: • F or composite video and S-V ideo upcon v ersion for the COMPONENT VIDEO MONITOR OUT 1 or 2, the HDMI Monitor setting must be set to No (see page 45). See page 27 for more information on video signal flow and upcon version.
50 First Time Setup —Continued If you connect a component to a digital audio input, you must assign that input to an input selector . F or example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the CD input selector .
51 First Time Setup —Continued Notes: • Only FR ONT can be assigned to the A UX 2 input selector . • The TUNER input selector cannot be assigned and is fixed at the “- - -” option. • When an HDMI IN is assigned to an input selector in “HDMI V ideo Setup” on page 46, this input assign- ment is automatically set to the same HDMI IN.
52 First Time Setup —Continued If you connect a component to the A V receiver’ s analog multichannel input, you must assign that input to an input selector . F or example, if you connect your D VD player to the MUL TI CH input, you must assign it to the D VD input selector .
53 First Time Setup —Continued W ith the supplied speaker setup microphone, Audyssey MultEQ XT can measure the number of speakers con- nected, their sizes, crossov er frequencies, and distances from the listening position and calculate the optimal speaker settings for you automatically .
54 First Time Setup —Continued 1 T urn on the A V receiver and the connected TV . On the TV , select the input to which the AV receiv er is connected. 2 Place the setup microphone at the 1st measurement position, and connect it to the Setup Mic jack.
55 First Time Setup —Continued Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 101) will be set to Audyssey . •Y ou can cancel the automatic speaker setup at any point in the procedure simply by disconnecting the setup microphone.
56 First Time Setup —Continued Speaker Detect Error This message appears if a speaker is not detected. “Y es” means that a speaker was detected. “No” means that no speaker was detected. Check your speak er connections and retry , or cancel the automatic speaker setup.
57 First Time Setup —Continued Revie wing the Results Changing the Speaker Settings Manuall y In some cases, the measurements taken by the automatic speaker setup may not provide usable results. If running the speaker setup a second time doesn’ t help, you’ll hav e to set the speaker settings manually (see pages 96–101).
58 First Time Setup —Continued For the onscreen setup menus to display properly , you must specify the TV system used in your area. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
59 First Time Setup —Continued For AM tuning to work properly , you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
60 Pla ying Y our A V Components Basic A V Receiver Operation 3 1 + - On Standby TV Input TV CH TV VOL -- / --- 10 11 12 D.TUN +10 0 Clear 123 456 789 Input Selector VCR / DVR CBL / SAT DVD Tape Tuner.
61 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears.
62 Listening to the Radio —Continued ■ T uning into Stations by Frequenc y Y ou can tune into AM and FM stations directly by enter- ing the appropriate frequency . Displaying AM/FM Radio Inf ormation Note: • When you select a preset with a custom name (see page 104), its name is displayed instead of the band and frequency .
63 Listening to the Radio —Continued RDS only works in areas where RDS broadcasts are av ailable. When tuned to an RDS station, the RDS indi- cator appears. ■ What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals.
64 Listening to the Radio —Continued Displaying Radio T ext (R T) When tuned to an RDS station that’ s broadcasting te xt information, the text can be displayed. Notes: • The message “W aiting” may appear while the A V receiv er waits for the R T information.
65 Listening to the Radio —Continued Note: Hardware and required monthly subscription sold sepa- rately . Other fees and taxes, including a one-time activ a- tion fee may apply . Subscription fee is consumer only . All fees and programming subject to change.
66 Listening to the Radio —Continued Selecting XM Satellite Radio Signing Up for XM Satellite Radio Once you hav e installed the XM Mini-T uner and Home Dock, you are ready to subscribe to XM Satellite Radio. Y ou’ll need a major credit card and your XM Radio ID.
67 Listening to the Radio —Continued Notes: • RADIO ID cannot be selected in Category Search mode. Y ou must select Channel Search mode (see right column).
68 Listening to the Radio —Continued Selecting Channels on the A V receiver: Selecting the Previous Channel: Displaying XM Radio Inf ormation The following information can be displayed: Notes: • If the category , artist, or song title is not av ailable, “- - -” will be displayed instead.
69 Listening to the Radio —Continued Notes: • So long as the signal strength is good, you can enjoy XM Radio by using either satellite or terrestrial recep- tion. •T errestrial signals are only av ailable in certain areas. • The XM information is only displayed when the Sat- ellite Radio mode is set to XM or XM/SIRIUS (see page 66).
70 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Installation costs and other fees and taxes, including a one-time activ ation fee may apply . Subscrip- tion fee is consumer only . All fees and programming subject to change.
71 Listening to the Radio —Continued Setting the Satellite Radio Mode Before you can listen to SIRIUS Satellite Radio, you must set the Satellite Radio mode to SIRIUS. Selecting SIRIUS Satellite Radio 1 Press the [Receiver] Remote Mode button, f ollowed b y the [Setup] button.
72 Listening to the Radio —Continued Signing Up for SIRIUS Satellite Radio Before you can use SIRIUS Satellite Radio, you must first sign up for an account. Y ou’ll need a major credit card and your SIRIUS Satellite Radio ID, which you can get from the A V receiver, as e xplained below , or from the SiriusConnect Home tuner package.
73 Listening to the Radio —Continued Notes: • If you select an unav ailable channel, “INV ALID CHANNEL” appears on the display . • If you select a channel that you are not subscribed to, “CALL SIRIUS” appears on the display . • Channels that are locked must be unlocked before you can listen to them.
74 Listening to the Radio —Continued Notes: • While a channel is locked, it cannot be selected for listening. •T o unlock a channel, you must enter the correct PIN number and change it to Unlocked in step 6. Changing the PIN Number 4 Press the [D .
75 2 Use the Up and Down [ ]/[ ] buttons to select “4. Sour ce Setup, ” and then press [Enter]. The Source Setup menu appears. Note: If the Satellite Radio mode is set to None or XM (see page 71), the “5. SIR- IUS Parental Lock” item is not a vail- able.
76 Listening to the Radio —Continued Displaying SIRIUS Satellite Radio Information The following information can be displayed: Notes: • If the category , artist/composer , or song title is not av ailable, “- - -” will be displayed instead.
77 Listening to the Radio —Continued Notes: • So long as the signal strength is good, you can enjoy SIRIUS Satellite Radio by using either satellite or ter- restrial reception.
78 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM, FM, XM, and SIRIUS radio stations. Note: •Y ou can name your radio presets for easy identifica- tion (see page 104).
79 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiver is set to Standby .
80 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [Sleep] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [Sleep] b utton.
81 Common Functions —Continued If you connect a component to more than one audio input, such as a D VD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [Audio Sel] button to select which audio input you w ant to use to listen to that component.
82 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 87. Selecting on the A V Receiver ■ [Stereo] button This button selects the Stereo listening mode.
83 Using the Listening Modes —Continued Analog and PCM Sources Listening Modes A v ailable for Eac h Source Format Button Source f ormat PCM Multi channel analog Multichannel PCM 32–96 kHz 176.4/ 192kHz* 1 32–96 kHz 176.4/192 kHz *1 *1. DVD-Audio discs output multichannel 176.
84 Using the Listening Modes —Continued DSD , Dolby Digital, and Dolb y Digital Plus Sources Button Source f ormat DSD *1 *1. In listening modes other than DSD Direct, DSD sources are converted and handled as PCM.
85 Using the Listening Modes —Continued T rueHD and DTS Sources Button Source f ormat T rueHD *1 *1. 192 kHz TrueHD sources are processed as 192 kHz/2-channel audio signal, regardless its number of channels.
86 Using the Listening Modes —Continued DTS-HD Sources Button Source f ormat DTS-HD High Resolution DTS-HD Master Audio *1 *1. 192 kHz DTS-HD Master Audio sources are processed at 96 kHz.
87 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction.
88 Using the Listening Modes —Continued DTS-HD Master Audio Designed to take full adv antage of the additional storage space offered by the ne w Blu-ray and HD D VD disc for- mats, this new DTS format of fers up to 7.1 discrete chan- nels of uncompressed digital audio with 96 kHz/24-bit sampling rate and signal resolution.
89 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the analog multichannel input cannot be recorded.
90 Onscreen Setup Menus The onscreen setup menus appear on the connected TV and pro vide a con ve- nient way to change the A V receiv er’ s v arious settings. Settings are organized into eight categories on the main menu , most containing a submenu .
91 Adjusting the Listening Modes W ith the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing.
92 Adjusting the Listening Modes —Continued W ith the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. T one Control Settings Y ou can adjust the tone (bass and treble) of the front, center , surround, and surround back speakers indi vidu- ally .
93 Adjusting the Listening Modes —Continued Direct Setting Delay Enable ■ DSD This setting determines whether or not DSD (SA CD) audio signals are passed through the DSP for A/V Sync, delay , etc., processing when the Direct listening mode is selected.
94 Adjusting the Listening Modes —Continued Dolby Digital Settings ■ Dolby EX This setting determines how Dolby EX signals are han- dled. A uto: When the source is Dolby EX, you can select the Dolby EX or THX Surround EX listening mode.
95 Adjusting the Listening Modes —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. 3 Use the Up and Down [ ]/[ ] buttons to select an input selec- tor , and then press [Enter].
96 Ad v anced Setup This section explains items on the Speaker Config menu. Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 53).
97 Adv anced Setup —Continued 5 Use the Up and Down [ ]/[ ] buttons to select “Front, ” and then use the Left and Right [ ]/[ ] buttons to select a crosso ver frequency .
98 Adv anced Setup —Continued Low-P ass Filter f or the LFE Channel W ith this setting, you can specify the cutoff frequenc y of the LFE channel’ s lo w-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
99 Adv anced Setup —Continued Speaker Distance W ith the Speaker Distance settings, you can specify the distance from each speaker to the listening position. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
100 Adv anced Setup —Continued Speaker Level Calibration W ith the Lev el Calibration settings, you can adjust the lev el of each speaker while listening to the test tone so that the volume of each speak er is the same at the listen- ing position.
101 Adv anced Setup —Continued Equalizer Settings W ith the Equalizer settings, you can adjust the tone of speakers indi vidually with a 15-band equalizer . The v ol- ume of each speaker can be set on page 100. 1 Press the [Receiver] Remote Mode button, f ollowed b y the [Setup] button.
102 Adv anced Setup —Continued Notes: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
103 Adv anced Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. This section explains items on the Source Setup menu. Items can be set individually for each input selector .
104 Adv anced Setup —Continued IntelliV olume W ith IntelliV olume, you can set the input level for each input selector individually . This is useful if one of your source components is louder or quieter than the others.
105 Adv anced Setup —Continued Notes: •T o store a name, you must select “OK” and press [Enter] in step 7, otherwise it will not be sav ed. •Y ou cannot enter a custom name for XM or SIRIUS radio presets. • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons.
106 Adv anced Setup —Continued This section explains items on the Miscellaneous menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. V olume Setup ■ V olume Display W ith this setting, you can choose how the v olume lev el is displayed.
107 Adv anced Setup —Continued ■ Po wer On V olume This setting determines what the volume will be each time the A V receiver is turned on. When the V olume Display preference is set to Absolute, the range is Last, Min, 1 to Max. When it’ s set to Rela- tiv e, the range is Last, – ∞ dB, –81 dB to +18 dB.
108 Adv anced Setup —Continued This section explains items on the Hardware menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup], [Enter], and arrow b ut- tons. Remote Control ■ Remote ID When sev eral Integra/Onk yo components are used in the same room, their remote ID codes may ov erlap.
109 Adv anced Setup —Continued T uner ■ AM Freq Step (on some models) See “ AM Frequency Step Setup (on some models)” on page 59. ■ Satellite Radio (on North American model) If you connect a.
110 Adv anced Setup —Continued • HDMI power control only w orks with HDMI-compat- ible components that support it and may not work properly with some components due to their settings or compatibility . • When set to Enable, the A V receiver consumes more power .
111 Zone 2 and Zone 3 In addition to your main listening room, you can also enjoy playback in two other rooms, or as we call them, Zone 2 and Zone 3. And, you can select a dif ferent source for each room. There are two ways you can connect Zone 2 speak ers: 1.
112 Zone 2 and Zone 3 —Continued Zone 2 Video Outputs The A V receiver features a composite video output and component video output for connection to a TV in Zone 2, so you can enjoy both audio and video in that zone.
113 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 speak ers to the A V receiv er, as explained in “Connecting Y our Zone 2 Speakers Directly to the A V receiv er” on page 111, you must set the Powered Zone 2 setting to Act (Activ ated).
114 Zone 2 and Zone 3 —Continued If you’ ve connected your Zone 2 or Zone 3 speak ers to an amp with no volume control, set the Zone 2 Out or Zone 3 Out setting, respectiv ely , to V ariable so that you can set the zone’ s v olume, balance, and tone on the A V receiv er.
115 Zone 2 and Zone 3 —Continued Selecting an Input Source f or Zones Notes: •T o select AM or FM, press the [T uner] input selector b utton repeatedly . On the North American model, you can also select XM or SIRIUS. • Only analog input sources are output by Zone 2 and Zone 3.
116 Zone 2 and Zone 3 —Continued Adjusting the V olume of Zones Adjusting the Balance of Zones Muting Zones Adjusting the T one of Zone 2 Notes: • Zones can also be unmuted by adjusting the volume.
117 Zone 2 and Zone 3 —Continued The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when the y are selected as the input source. The triggers can be set so that they acti vate when a connected component is selected as the input source for the main room, Zone 2, Zone 3, or any combination of rooms.
118 Zone 2 and Zone 3 —Continued To control the A V receiver with the remote controller while you’ re in Zone 2 or Zone 3, you’ll need a commer - cially av ailable multiroom remote control kit for each zone. • Multiroom kits are made by Niles and Xantech.
119 Contr olling Other Components Y ou can control your other components, including those made by other manufacturers, with the remote controller . This section explains ho w to: • Enter the remote control code for a component that you want to control: D VD, TV , VCR, etc.
120 Controlling Other Components —Continued Remote Control Codes f or Integra/Onky o Components Connected via Integra/Onk yo components that are connected via are controlled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example.
121 Controlling Other Components —Continued To control another component, point the remote controller at it and use the buttons explained belo w . (Y ou must select the appropriate remote controller mode with the Remote Mode buttons first.) W ith some components, certain buttons may not work as expected, and some may not w ork at all.
122 Controlling Other Components —Continued The A V receiver’ s remote controller can learn the com- mands of other remote controllers. By transmitting, for example, the Play command from your CD .
123 Controlling Other Components —Continued Y ou can program the remote controller’ s Macro buttons to perform a sequence of remote control actions. Example: To play a CD you typically need to perform the follow- ing actions: 1. Press the [Receiv er] Remote Mode button to select the Receiv er remote controller mode.
124 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased this unit. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly .
125 Tr oubleshooting —Continued The subwoof er produces no sound • If the source material contains no audio in the LFE channel, the subwoofer produces no sound. • Check the Speaker Configuration (page 96). The Zone 2/3 speakers pr oduce no sound • The Zone 2/3 speakers only output sources that are connected to an analog input.
126 Tr oubleshooting —Continued • Listen to the station in mono (page 61). • When listening to an AM station, operating the remote controller may cause noise. •P assing cars and airplanes can cause interference. • Concrete walls weaken radio signals.
127 Specifications Amplifier Section Video Section T uner Section ■ FM ■ AM ■ Digital T uner General ■ Video Input ■ Video Output ■ A udio Inputs ■ A udio Outputs ■ Control T erminal Specifications and features are subject to change without notice.
SN 29344459A (C) Copyright 2007 ONKY O CORPORA TION Japan. All rights reserved. I0805-2 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.
Een belangrijk punt na aankoop van elk apparaat Integra DTR-7.8 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Integra DTR-7.8 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Integra DTR-7.8 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Integra DTR-7.8 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Integra DTR-7.8 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Integra DTR-7.8 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Integra DTR-7.8 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Integra DTR-7.8 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
