Gebruiksaanwijzing /service van het product EZ-Extender van de fabrikant Analog Devices
Ga naar pagina of 35
SHARC ® EZ-Extender ® Manual Revision 3.0, April 2006 Part Number 82-000805-01 Analog Devices, Inc. One T echnology W ay N orwood, Mass. 02062-9106 a.
Copyright Information ©2006 Analog Devices, Inc., ALL RIGH TS RESERVED. This document may not be reproduced in any form wi thout prior, express written consent from Analog Devices, Inc.
Regulatory Compliance The SHARC EZ-Extender has been certif ied to comply with the essential requirements of the European EM C directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “ CE ” mark.
iv SHARC EZ-Extender Manual.
SHARC EZ-Extender Manual v CONTENTS PRE F A C E P urpose of This Manual ................................................................ viii Intended A udience .......................................................................... ix Manual Contents .
CONTENTS vi SHARC EZ-Extender Manual DIP S witches and J umpers ............................................................ 2-3 Dir ection/Clock Source Contr ol S witch (SW1) ........................ 2-3 MISO Disconnect J umper (P6) .................
SHARC EZ-Extender Manual vii PREFACE Thank you for purchasing the SHARC ® EZ-Extender ® , Analog Devices (ADI) extension board to the EZ-KIT Lite ® evaluation system for ADSP-21262 SHARC processors.
Purpose of This Manual viii SHARC EZ-Extender Manual The board extends the capabilities of th e evaluation system by providing a connection between the parallel data access port (PDAP) of the ADSP-21262 processor and an Analog Devices analog-to-digital high-speed converter (ADC HSC) evaluation board.
SHARC EZ-Extender Manual ix Preface Intended Audience This manual is a user’s guide and reference to the SHARC EZ-Extender. Programmers who are famil iar with the Analog Devices SHARC processor architecture, operation, and developme nt tools are the primary audie nce for this manual.
What’s New in This Manual x SHARC EZ-Extender Manual • Appendix B, “EZ-Extender Schematic” on page B-1 Provides the resources to allow modifications to the EZ-Extender or to use as a reference design. L Appendix B now is part of the online Help.
SHARC EZ-Extender Manual xi Preface • Contact your Analog Devices, I nc. local sales office or authorized distributor • Send questions by mail to: Analog Devices, Inc. One Technology Way P.O. Box 9106 Norwood, MA 02062-9106 USA Supported Products The SHARC EZ-Extender is designed as an extension to the ADSP-21262 EZ-KIT Lite evaluation system.
Product Information xii SHARC EZ-Extender Manual Registration: Visit www.myanalog.com to sign up. Click Register to use My Analog.com. Registration takes about five minutes an d serves as means for you to select the information you want to receive. If you are already a registered user, just log on.
SHARC EZ-Extender Manual xiii Preface L If you plan to use the EZ-KIT Lite board in conjunction with a JTAG emulator, also refer to the documentatio n that accompanies the emulator. All documentation is avai lable online. Most docume ntation is av ailable in printed form.
Product Information xiv SHARC EZ-Extender Manual Online Technical Documentation Online documentation comprises the VisualDSP++ Help system, software tools manuals, hardware tools manu als, processor manuals, the Dinkum Abridged C++ library, and Flexible License Manager (FlexLM) network license manager software documentatio n.
SHARC EZ-Extender Manual xv Preface Notation Conventions Text conventions used in this manual are identified and described as follows. L Additional conventions, which apply only to specific chapters, may appear throughout this document.
Notation Conventions xvi SHARC EZ-Extender Manual.
SHARC EZ-Extender Manual 1-1 1 EZ-EXTENDER INTERFACES This chapter relates how the extender interfaces with the co mpatible boards. The information is presen ted in the following sections.
Breadboard Area 1-2 SHARC EZ-Extender Manual Switch (SW1)” on page 2-3 . The setup of the general-purpose signals DAI_P15_GP1 and DAI_P16_GP2 is dependent on the specific ADC HSC evaluation board being interfaced; therefore, the board’s model must be taken into consideration.
SHARC EZ-Extender Manual 2-1 2 EZ-EXTENDER HARDWARE REFERENCE This chapter describes the hardware design of the SHARC EZ-Extender. The following topics are covered. • “System Architecture” on page 2-1 Describes the configuration of th e extender and explains how the board components interface with the processor and EZ-KIT Lite.
System Architecture 2-2 SHARC EZ-Extender Manual The block diagram in Figure 2-1 shows that each clock and general-pur - pose signal attached to the analog-to -digital high-speed converter (ADC HSC) interface is configured depending on how the interface operates.
SHARC EZ-Extender Manual 2-3 EZ-Extender Hardware Reference ing a socket with an osci llator. Only one of these sources can be used at a time, the other sources must be disabl ed. For more information on how to disable the TX_CLK sources, see “SMA Connector Clock Disconnect Jumper (P10)” on page 2-5 .
DIP Switches and Jumpers 2-4 SHARC EZ-Extender Manual When the SW1 switch connects a direction control signal to ground ( GND ), the corresponding signal (s ignals) is (are) controll ed as input. The direc - tion control functionalit y is summarized in Table 2-1 .
SHARC EZ-Extender Manual 2-5 EZ-Extender Hardware Reference MISO Disconnect Jumper (P6) The MISO signal of the serial peripheral interconnect (SPI) connector ( J2 ) is driven by a buffer to the processor’s MISO signal, as illustrated in Figure 2-1 on page 2-2 .
DIP Switches and Jumpers 2-6 SHARC EZ-Extender Manual.
SHARC EZ-Extender Manual A-1 A EZ-EXTENDER BILL OF MATERIALS The bill of materials corresponds to “EZ-Extender Schematic” on page B-1 . Please check the latest sche matic on the Analog Devices Web site: http://www.analog.com/Processors/Pr ocessors/DevelopmentTools/tec hnicalLibrary/manuals/DevToolsIndex .
A-2 SHARC EZ-Extender Manual 10 1 RJ45 8PIN CON_RJ45 J2 TYCO 1-16609214-1 11 1 SMA XPINS CON043 J3 JOHNSON COMP 142-0701-201 12 2 IDC 2X1 IDC2X1 P6,P10 FCI 90726-402HLF 13 2 IDC 2PIN_JUM PER_ SHOR T SJ1-2 DIGI-KEY S9001-ND 14 1 51 1/8W 5% 1206 R9 VISHA Y CR CW120651R0JKEA 15 14 0.
D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
5V 5V 5V 5V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
5V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
3.3V 3.3V 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0182-2003 2.
SHARC EZ-Extender Manual I-1 II N D E X A ADC (analog-to-digital converter) interface, 1-1 , 2-2 address bus, 2-3 ADSP-21262 processors clock in signal (DAI_PP2_CLOCKIN ), 2-3 , 2-4 MIS0 signal, 2-5 A.
INDEX I-2 SHARC EZ-Extender Manual J jumpers, 2-3 clock disconnect (P10), 2-5 MISO disconnect (P6), 2-5 M MISO disconnect jumper (P6), 2-5 N notation conventions, -xv O oscillator, 2-3 P P10 (SMA conn.
Een belangrijk punt na aankoop van elk apparaat Analog Devices EZ-Extender (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Analog Devices EZ-Extender heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Analog Devices EZ-Extender vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Analog Devices EZ-Extender leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Analog Devices EZ-Extender krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Analog Devices EZ-Extender bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Analog Devices EZ-Extender kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Analog Devices EZ-Extender . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
