Gebruiksaanwijzing /service van het product 864 ST van de fabrikant Lopi
Ga naar pagina of 32
864 ST F ir ep lace • Operation • Maintenance Tested and Listed by OMNI-Test Laboratories, Inc. Beaverton, Oregon Report # 028-F-84-5 ANSI Z21.88b-2003 WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
2 Introduction Travis Industries 4071130 100-01196_000 Introduction We welcome you as a new owner of a 864 ST gas fireplace. This manual details operation and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your heater and save the manual for future reference.
Introduction 3 © Travis Industries 4071130 100-01196_000 Table of Contents Introduction and Important Information Introduction ............................................................. 2 Important Information .....................................
4 Safety Precautions © Travis Industries 4071130 100-01196_000 IF YOU SMELL GAS: * Do not light any appliance * Extinguish any open flame * Do not touch any electrical switch or plug or unplug anythi.
Safety Precautions 5 © Travis Industries 4071130 100-01196_000 Do not place clothin g or other flammable items on or near the heater. Because this heater can be controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed on or near it.
6 Operation © Travis Industries 4071130 100-01196_000 Before You Begin • Read this entire manual before you use your new fireplace (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death.
Operation 7 © Travis Industries 4071130 100-01196_000 Starting The Pilot Flame The pilot flame is required to ignite the main burners (it also plays a safety role). It should be left on once lit. It will stay lit unless the gas control valve is turned to "OFF".
8 Operation © Travis Industries 4071130 100-01196_000 Starting the Fireplace for the First Time • Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur.
Operation 9 © Travis Industries 4071130 100-01196_000 Adjusting the Optional Blower Speed The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to temperature (approximately 10 minutes after starting).
10 Maintenance © Travis Industries 4071130 100-01196_000 Maintaining Your Fireplace's Appearance Fingerprints or other marks left on the optional plated surface may become etched in place if they are not wiped clean prior to turning the fireplace on.
Maintenance 11 © Travis Industries 4071130 100-01196_000 Grill Installation and Removal Some fireplaces have grills above and below the glass frame. These grills may be installed following the directions below (follow in reverse to remove).
12 Maintenance © Travis Industries 4071130 100-01196_000 Face Installation and Removal Some fireplaces have a face that fits over the glass frame. The face can be removed following the directions below. Phillips Screwdriver Four screws hold the face in place.
Maintenance 13 © Travis Industries 4071130 100-01196_000 Glass Frame Removal and Installation Warning: The appliance must be completely cool before removing the glass.
14 Maintenance © Travis Industries 4071130 100-01196_000 Glass Frame Removal and Installation (continued) The latch can come loose from glass frame anchor. This occurs when it is turned 1/4 turn when it is disengaged. Follow the directions below to re-install the latch if it becomes loose.
Maintenance 15 © Travis Industries 4071130 100-01196_000 Log Set Installation Logs in Place – FRONT SIDE NOTE : This fireplace has a front side and back side.
16 Maintenance © Travis Industries 4071130 100-01196_000 Center Log Installation The log shelf has two tabs used to align the center log. Bend these tabs as shown to the right. Place the center log in place. M ake sure the two tabs on the log shelf insert into the two holes on the bottom of the log.
Maintenance 17 © Travis Industries 4071130 100-01196_000 Front Left Log Place the front left log as shown below. There is a ledge on the bottom of the log that aligns with the edge of the center burner. When in place, the front left log has a small gap to the center log.
18 Maintenance © Travis Industries 4071130 100-01196_000 Front Left Upper Log There are two pins on the front left log. The pin to the right is used to locate the front left upper log. The front left upper log has a groove and one hole on the bottom.
Maintenance 19 © Travis Industries 4071130 100-01196_000 Front Upper Center Log The front upper center log has two holes on its bottom surface. One of the holes fits over the pin on the center log (see picture to the right). The other fits over the pin on the front left log.
20 Maintenance © Travis Industries 4071130 100-01196_000 Back Left Log The back left log fits to the left of the center log. The groove on the bottom of the log fits over the upper burner tray. Make sure to slide the log towards the center of the firebox.
Maintenance 21 © Travis Industries 4071130 100-01196_000 Right Ember Chunk The right ember chunk is installed from the back. The groove on the bottom of the ember fits over the edge of the upper burner tray. It wedges between the two logs.. When in place, the left ember chunk looks like the picture to the right.
22 Maintenance © Travis Industries 4071130 100-01196_000 Back Left Log The pin on the center log inserts into the hole on the back of the back left log. This groove on the log fits over the grate. When in place, the log looks like the picture to the right.
Maintenance 23 © Travis Industries 4071130 100-01196_000 Back Upper Right Log Pins on the center log and back right log help locate this log. When in place, the back upper right log looks like the picture to the right.
24 Maintenance © Travis Industries 4071130 100-01196_000 Ember Placement A bag of embers is provided to further enhance the firebox. Place the embers on the firebox floor and on the outer burner (especially over exposed rivets on the burner). Do not place embers over any of the burner holes or air channels.
Maintenance 25 © Travis Industries 4071130 100-01196_000 Glass Cleaning The glass may be cleaned with a non- abrasive cleaner. To clean the inside of the glass, simply remove the glass frame, place it on a non-scratching surface, and clean the inside surface.
26 Maintenance © Travis Industries 4071130 100-01196_000 Troubleshooting Table Problem: Possible Cause: Don't Call for Service Until You: Pilot Will Not Light A gas shut off valve is turned off .
Maintenance 27 © Travis Industries 4071130 100-01196_000 How this Fireplace Works This fireplace was designed with safety as the primary concern. Many of the components inside this fireplace are for safety purposes. Therefore, only certified gas service technicians should service this fireplace.
28 Maintenance © Travis Industries 4071130 100-01196_000 Wiring Diagram Millivolt Wiring (stock configuration) Orange White Piezo Igniter Thermopile Red Thermocouple Copper Co-Axial Wire Red Optional.
Warranty 29 © Travis Industries 4071130 100-01196_000 To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed Warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd.
30 Optional Equipment © Travis Industries 4071130 100-01196_000 Accessories The accessories listed below are available at your Travis dealer. To locate a dealer, visit: www.travisproducts.com Firebacks There are several styles of decorative ceramic firebacks that fit inside the firebox and enhance the area behind the flames.
Optional Equipment 31 © Travis Industries 4071130 100-01196_000.
32 Index © Travis Industries 4071130 100-01196_000 Index Accessories .......................................................3 0 Adjusting the Flame Height ..................................8 Adjusting the Optional Blower Speed ......................9 Before You Begin .
Een belangrijk punt na aankoop van elk apparaat Lopi 864 ST (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Lopi 864 ST heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Lopi 864 ST vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Lopi 864 ST leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Lopi 864 ST krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Lopi 864 ST bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Lopi 864 ST kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Lopi 864 ST . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
