Gebruiksaanwijzing /service van het product LT31S van de fabrikant MTD
Ga naar pagina of 20
Operator’ s Manual L T31S 2-Cycle Petr ol T rimmer IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y P/N 769-01661 (2/05).
2 INTRODUCTION T ABLE OF CONTENTS Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3 Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Assembly Instructions .
3 RULES FOR SAFE OPERA TION SYMBOL MEANING The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
4 RULES FOR SAFE OPERA TION • Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Remove the fuel cap slowly, and only after the engine stops. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately.
5 SAFETY AND INTERNA TIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
6 KNOW YOUR UNIT APPLICA TIONS As a trimmer: • Cutting grass and light weeds • Edging • Decorative trimming around trees, fences, etc. KNOW YOUR UNIT Fuel Cap Throttle Control D-Handle Shaft Gri.
7 ASSEMBL Y INSTRUCTIONS Fig. 2 INST ALL AND ADJUST THE D-HANDLE 1. Push the D-handle down onto the shaft housing so that the handle slants towards the shaft grip (Fig. 1). The squared bolt hole in the handle is to the right. 2. Insert the shoulder bolt into the squared hole in the handle and push through.
8 OIL AND PETROL INFORMA TION NOTE: Dispose of the old petrol/oil mix in accordance to Federal, State and Local regulations. OIL AND PETROL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, clean unleaded petrol.
9 ST ARTING/STOPPING INSTRUCTIONS Fig. 6 Starting Position Start/On (I) Stop/Off (O) Starter Rope Throttle Control Fig. 8 Fig. 7 Blue Choke Lever Position 1 Position 3 Position 2 Primer Bulb Operate this unit only in a well- ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area.
10 OPERA TING INSTRUCTIONS NOTE: Do not rest the Bump Head™ on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue .
11 MAINTENANCE AND REP AIR INSTRUCTIONS MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any seasonal tune-up. NOTE: Some maintenance procedures may require special tools or skills.
12 MAINTENANCE AND REP AIR INSTRUCTIONS Fig. 19 Fig. 15 NOTE: SplitLine™ can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel. Use Figure 15 to identify the inner reel you have. NOTE: Always use the correct line length when installing trimming line on the unit.
13 MAINTENANCE AND REP AIR INSTRUCTIONS AIR FIL TER MAINTENANCE Removing the Air Filter/Muffler Cover 1. Place the blue choke lever in Position 2 (Fig. 21). NOTE: The blue choke lever must be in Position 2 to remove the air filter/ muffler cover. 2. Remove the four (4) screws securing the air filter/muffler cover (Fig.
14 MAINTENANCE AND REP AIR INSTRUCTIONS CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the air filter/muffler cover (Fig. 27). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.
15 MAINTENANCE AND REP AIR INSTRUCTIONS Clean Air Filter The condition of the air filter is important to the operation of the unit. A dirty air filter will restrict air flow and change the air/fuel mixture. This is often mistaken for an out of adjustment carburetor.
16 MAINTENANCE AND REP AIR INSTRUCTIONS CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle.
17 TROUBLESHOOTING If further assistance is requir ed, contact your authorized service dealer . CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting at.
18 SPECIFICA TIONS ENGINE* DRIVE SHAFT and CUTTING A TT ACHMENT* *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Engine Type...........
19 NOTES.
20 NOTES.
Een belangrijk punt na aankoop van elk apparaat MTD LT31S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen MTD LT31S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens MTD LT31S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding MTD LT31S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over MTD LT31S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van MTD LT31S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de MTD LT31S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met MTD LT31S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
