Gebruiksaanwijzing /service van het product XP-600 van de fabrikant Napco Security Technologies
Ga naar pagina of 16
Using Your XP-600 Securit y System ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 NAPCO Oi218a.pub page 1 Thursday, December 18, 1997 18:29.
Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-600 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today.
3 1 Bell / Battery Test Test your bell or siren by pressing A followed by 1 .This will cause the bell, or siren to sound for 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be performed on weekends or at a time designated by your alarm company) 1.
ARMED READY SYSTEM ü FIRE AC ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 4 Keypad Controls and Indicators Ready Light will light when all zones are secure and system is ready to be Armed.
Arming Your System When Leaving 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding.
Protecting Yourself While at Home 1 Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding.
Emergency Buttons The three sets of emergency buttons, if programmed, are always active whether the system is armed or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated when the two respective buttons are pressed at the same time.
Disarming Your System when Returning 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. 2 Enter your user code. The Red Armed light will go out, indicating that the system has been disarmed.
Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepare your plan, draw floor plans of your building. (space is provided on the next page) Show two exits - a front or back door and a window from each room.
10 Fire Protection Floorplan Draw a plan of your premises below. Oi218a.pub page 10 Thursday, December 18, 1997 18:29.
Special Functions A By pressing A followed by the appropriate key, (do not press simultaneously) these special functions and features can be enabled: A0 Easy Arm (when system is disarmed) The Easy Arm feature allows the system to be armed by pressing A followed by 0 .
The XP600 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the yellow ü ü SYSTEM light and beeping the keypad buzzer.
13 ü ü System Troubles Keypad Beeps or ü ü SYSTEM Flashes Zone light ON System Trouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detected in the Fire Circuit. Call installing company for service. 2 Beeps 3 Wireless Receiver Trouble A problem has been detected with the wireless receiver.
Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program other user codes. The following explains how you will use this code to program or erase additional user codes.
Ambush Code - In the event that you are forced by an intruder to dis- arm your system, this special code can be used to disarm the system, and simultaneously send a silent alarm to Central Station.
NAPCO LIMITED WARRANTY THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception.
Een belangrijk punt na aankoop van elk apparaat Napco Security Technologies XP-600 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Napco Security Technologies XP-600 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Napco Security Technologies XP-600 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Napco Security Technologies XP-600 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Napco Security Technologies XP-600 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Napco Security Technologies XP-600 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Napco Security Technologies XP-600 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Napco Security Technologies XP-600 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
